ADXMT0125 ADX Firebase MT01 Monitor Mount Instruction Manual

: September 18, 2024
: adx

Table of Contents

ADXMT0125 ADX Firebase MT01 Monitor Mount
Specifications
Product Usage Instructions
Installation
- FAQ
Q: Can this monitor mount be used with any type of monitor or
Q: Is it necessary to use all the provided screws and spacers
Q: How many people are recommended for assembling this monitor

ADXMT0125 ADX Firebase MT01 Monitor Mount

“`html

Specifications

Screen Size: 32-50 inches
Max Monitor/TV Load: 35 kg
VESA Compliance: 75×75, 100×100, 200×100, 200×200, 300×200,
400×200

Product Usage Instructions

Installation

Before installation: Use the provided spirit
level to ensure the racing seat is level.
Remove Screws: Remove the four screws from the
racing seat (ADXRS0325). Retain these screws for use in the next
step.
Mounting: Follow the diagram to mount the
monitor bracket using the provided screws and spacers. Use only the
necessary vesa mount screws based on your monitor or TV’s
manual.
Align Monitor/TV: Ensure the monitor/TV is
horizontally aligned. Adjust and tighten the screws
accordingly.
Tips: Organize cables using the provided clip.
Adjust the mount to align the center of the display with your eye
level for the best viewing experience.

FAQ

Q: Can this monitor mount be used with any type of monitor or

TV?

A: This mount is compatible only with VESA-compatible monitors
and TVs. Refer to the VESA Compliance specifications for supported
sizes.

Q: Is it necessary to use all the provided screws and spacers

during installation?

A: Only use the necessary vesa mount screws based on your
monitor or TV’s manual. Spacers should be used for specific
scenarios as mentioned in the instructions.

Q: How many people are recommended for assembling this monitor

mount?

A: Two people are required to lift the unit during assembly for
safety reasons.

“`

Visit Partmaster.co.uk today for the easiest way to buy electrical spares and accessories. With over 1 million spares and accessories available we can deliver direct to your door the very next day. Visit www.partmaster.co.uk or call
0344 800 3456 (UK customers only) Calls charged at National Rate.

Currys Group Limited (co. no. 504877) 1 Portal Way, London, W3 6RS, UK
EU Representative Currys Ireland Limited (259460)
3rd Floor Office Suite Omni Park SC, Santry, Dublin 9, Republic of Ireland

IB-ADXMT0125-240718V1

MONITOR MOUNT
INSTRUCTION MANUAL ADXMT0125
For use exclusively with the ADX Firebase RS03 Racing Seat (ADXRS0325). Compatible only with VESA-compatible monitors and TVs.

FIREBASE

SAFETY

SCREEN SIZE 32″-50″

KG
MAX MONITOR/TV LOAD
35 kg

VESA COMPLIANCE 75×75 100×100 200×100 200×200 300×200 400×200

WARNING! READ THE FOLLOWING BEFORE STARTING INSTALLATION
· Ensure that you have received all parts according to the unpacking checklist prior to installation. If any parts are missing or faulty, contact your place of purchase for a replacement.
· Assembly is required. Please follow the assembly instructions. Improper installation may result in damage or severe personal injury. · Using the mount with products heavier than the rated weights indicated may result in instability, causing possible injury. · Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and
components. · Use the mounting screws provided and do not over-tighten them. · Safety gear and additional tools (not included) are required for the installation. This product should only be installed by
professionals. · Parts are heavy; take care when handling. Two people are required for installation during some steps. · Check that the product is secure and safe to use at regular intervals (at least every three months). · This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. · This product contains small items that could be a choking hazard if swallowed. Keep these items away from children. · Keep this quick start guide for future reference.

UNPACKING

A x 2

B x 1

C x 2

D x 2

E x 2
(Cable clip)

F x 4
(Spacer) Ø15 x Ø8 x 15

G x 2

H x 4
M8 × 50mm

I x 2
M6 × 14mm

J x 2
M6 × 20mm

K x 4
D8

L x 4

M x 1
5mm

N x 1
(spirit level)

Quick Start Guide
(Quick start guide)

Vesa Mount Screws, Spacers & Washers

O × 4
M4 × 12mm

M-A × 4
M5 × 14mm

M-B × 4
M6 × 14mm

M-C × 4
M8 × 20mm

M-D × 4
M6 × 30mm

M-E × 4
M8 × 30mm

M-F × 4
(Washer) D5-D8

M-G × 8
(Spacer) Ø15 x Ø8 x 5

M-H × 4
(Spacer) Ø15 x Ø8 x 15

INSTALLATION

Before installation, please use the provided spirit level (N) to

ensure the racing seat is level.

2

1

1.1 Remove the four screws as shown below from the racing seat (ADXRS0325). Retain these screws

for use in step 1.2.

1.1

M

1.2 A
A

BF HK

3

Additional tool
(not included)

C

M-B M-F

M-C/ M-D M-F
M-G

O/ M-A
M-F

Too Long Too Short
Only 4 of the vesa mount screws are needed. Refer to your monitor or TV’s manual to determine the correct screw size. Use the provided spacers (M-G, M-H) for monitors or TVs with curved or recessed backs, recessed mounting holes, or when additional clearance is needed to access input ports.
I
4

M-D/ M-E
M-F
M-G/ M-H

G I

5

2 people are required to lift the unit during

assembly.

N

5.1

If the monitor/TV is not horizontally aligned:
5.2 Adjust the top screws until it is level.
5.3 Tighten the bottom screws to secure it in place.

5.2

5.3

J

5.4