Multifunctional Bicycle Audio + Lights Phone Mount Instruciton Manual

: June 2, 2024
: Sharper Image

USER MANUAL

Multifunctional Bicycle Audio and Lighting Kit

Multifunctional Bicycle Audio and Lighting Kit Feature

Important Note:

The body of each unit is labeled with product series number (SN) sticker. Units that are without a SN stickerare not eligible for service and technical support. If you purchased this unit without a SN sticker, please return it to the place of sale immediately.

Dear Customer

Thank you for purchasing this product!

This Bicycle Audio and Lighting Kit uses a 32-bit ARM processor for peak
performance, and integrates Bluetooth, flashlight, power bank, music player, bicycle
bell, and cell phone holder functionality all into one compact package.

Before using the product, please read this manual carefully to avoid unnecessary
troubles. Please keep the manual for future reference.
Thanks again for purchasing our product!

FCC Notice

Changes or modifications to this device not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of FCC Rules. Operations should meet the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that
may cause undesired operation.

Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Product introduction

Parts List
1.Master unit————————————————————- 1 set
2.Micro USB cable—————————————————— 1 piece
3.Mounting bracket—————————————————– 1 piece
4.Rubber mat ———————————————————— 2 pieces
5.Certificate ————————————————————– 1 piece
6.External bell ———————————————————- 1 piece

Product Features

Product Features Part 1

Product Features Part 2

Basic operations

Powering on and off

Move the power switch right to the “ON” position to power on; move left to the “OFF” position to power off.
When the unit is turned on, it defaults to Bluetooth mode, and will audibly prompt the user, “Please connect your audio device”.

Charging devices and playing music through USB

Cell phones can be charged through the USB port. Just connect the USB end of the charging cable to the USB port.
Plug a USB flash drive with music files into the USB port. Mp3, WMA and WAV files are supported. The unit will begin playing the first track.

Recharging the battery and connecting the bell through micro USB

The unit’s built-in battery can be charged through the micro USB interface, whether the unit is powered on or off. During charging, the 4 battery status LEDs will flash. The LEDs will stop flashing once the battery is fully charged.
All functionality is available while the device is charging. To switch the unit off, toggle the ON/OFF switch.
The external bell can be connected through the micro USB interface. Press the
button to ring the bell; hold the button in the depressed position for a continuous ring. The unit must be on for the bell to function

Playing music through SD

Insert a MicroSD card into the slot until it snaps into place. Use the mode button to switch to SD playback mode. Mp3, WMA and WAV files are supported.
To eject the Micro SD card, gently depress the card until you feel the card bounce out of the slot.

Controlling volume and music play order

CH/VOL BUTTONS: Switching between tracks, raising and lowering volume
While in Bluetooth, USB, or SD mode:

Press the button to skip to next track. Press and hold the button to raise the volume. The unit will beep when the maximum volume level is reached.
Press the button to return to the previous track. Press and hold the button to lower the volume.

AUX Mode

To connect an audio source through AUX mode, use a 3.5mm AUX cable.

Using the microphone for Bluetooth calls

The microphone is located under the removable waterproof cover next to the micro USB slot. THE REMOVABLE COVER MUST BE OPEN FOR THE MICROPHONE TO FUNCTION PROPERLY. During a call, speak in the direction of the unit, and the microphone should pick up your voice.

Basic operations

Bluetooth pairing

Select Bluetooth mode.
Enable Bluetooth on your smartphone, and scan for devices. Connect to the
Bluetooth device with the name ZTB-F01 to pair your smartphone.
The default pairing password is 0000. When pairing is successful, the unit
announces,”your device is connected”; then, open the music player on the cell
phone to play music or make calls via Bluetooth.
Note: Certain phones may not require you to enter a password to complete the pairing process.
When the unit is turned on, it is immediately available to pair. When it successfully pairs with a device, it switches to Bluetooth mode automatically.
The unit announces, “your device is disconnected”, whenever a Bluetooth
connection is ended.

Function Buttons: LED, Phone, and Mode

LED

Press once to turn on a continuous LED flashlight, press again to activate a flashing LED flashlight, and press a third time to turn off the LED flashlight. NOTE: Answering Bluetooth calls will not change the LED mode.

Phone

When the phone is paired with the device via Bluetooth, press the mode button once to answer calls. During a call, press the mode button once to end the call. When the phone is paired with the device via Bluetooth, you can select the unit as an audio output source for any audio, from apps, videos, or music.

Switching between modes

Press and hold the mode button to toggle between Bluetooth, USB, SD, and AUX modes. When any device is unavailable, the corresponding mode will be skipped. For example, if no SD card is detected, the unit will skip over SD mode.

Mounting

Attaching the phone holder

Make sure that the unit is powered off. Firmly hold the unit in one hand.
Hold the mount with your other hand. Clamp the mount onto the unit as shown below, and then rotate the mount counter-clockwise, as shown below, until you hear a click.

Attaching the phone holder

Using the cell phone holder

Stretch the clamping arms to adjust to the size of your phone. The width is adjustable in the range of 50-86mm. The clamp will hold most popular smartphones.

Using the cell phone holder

Mounting

Attaching to your bike

Before mounting, read and understand all the steps

Make sure that the bicycle is on hard and firm ground.
Ensure that there is enough unobstructed space on your handlebars to mount the holder.
Remove the screws from the mounting clamp. Slide the non-slip rubber into the clamp. The rubber will sit between the clamp and the handlebars.
Mount the holder on the handlebar, and re-tighten the screws to secure the unit.
Sit on the bicycle, and adjust the speakerson the unit to an appropriate position.
Note: The unit should be mounted with the LEDs facing forward and the speakers nearest the rider.
Fully turn the handlebar left and right, to make sure that the unit is properly secured, and does not interfere with other bike equipment.

Attaching to your bike

Charging Tips

First-time charging of the unit will take six hours. Subsequent charges will take five
hours. The battery life of a fully charged unit is about 30 hours.
To prolong the life of the battery, please charge at least once every month.

Technical specifications