LINKSYS WDS060 Wemo Smart Dimmer User Guide

: June 5, 2024
: Linksys

LINKSYS WDS060 Wemo Smart Dimmer User Guide

Important to know

WARNING! Risk of electric shock

Incorrect installation could be dangerous or O illegal. Multiple breakers/fuses may need to be turned off for safe installation. Please call a professional electrician if you are unfamiliar or uncomfortable with electrical work.

Wemo Smart Dimmer can only replace single-pole switches.

If your light can be turned on from two different wall switches, that’s a 3-way switch and wemo Smart Dimmer is not compatible.

Neutral wires are required for setup.
These wires are typically whiTe and can be found in your electrical box.

What you’ll need

What’s included

Cover Plate
Wire Nuts
Dimmer and Screws (use the provided screws and don’t over-tighten)

Recommended tools

Compatible light bulbs

All incandescent light bulbs are dimmable, but not all LEDs and CFLs are. Go to wemo.com/bulbs for more information.

Maximum total wattage

Incandescent

| 400 Watts
250 Watts for multi-gang
---|---

LED and CFL

| 150 Watts
(Actual Wattage rating, not “equivalent”)

Install where your Wi-Fi signal is strong

Use your mobile device to test the signal
Keep your mobile device close to the Dimmer until you finish setup

Installing your Dimmer

Installation video

Scan this OR code to watch a video walking through Dimmer installation.

Turn power off

Shut off power to The switch you’re replacing at your fuse panel or circuit breaker.
Turn power off
WARNING! Risk of electric shock
Incorrect installation could be dangerous or illegal. Multiple breakers/fuses may need to ” be turned off for safe installation. Please call a professional electrician if you are unfamiliar or uncomfortable with electrical work.
Confirm that power is off
Remove the faceplate from the existing switch. Use a voltage tester to test BOTH sides of the switch. You may need to turn off more Than one circuit breaker/fuse.
Power is off Confirmation

Identify the NEUTRAL wires

Pull out existing switch
Unscrew the switch and genTly pull it out of the wall.
Do not remove any of the wires yet.
NEUTRAL wires

Find the NEUTRAL wires

Look for NEUTRAL wires (usually whiTe) in The wall. You need These to set up the Dimmer.

NOTE: You may have a different number of neutral wires Than shown.
Find the NEUTRAL wires

Test the NEUTRAL wires
Use a voltage tester to check that there is no power in the NEUTRAL wires from neighboring circuits. If necessary, shut off additional circuits unTil no voltage is found.

Detach the NEUTRAL wires
Unscrew the wire nut connecting the NEUTRAL wires.

Identify the GROUND wires

Look for the GROUND wires (usually green or solid copper) and unscrew the wire nut connecting them.
Identify the GROUND wires

NOTE: You may have a different number of ground wires than shown.

Identify and label LINE and LOAD wire

Peel off and apply The LINE and LOAD wire labels below. If you’re unsure which wire is which, we’ll help you in the next step.
NOTE: Your existing wires may be in different locations than shown.
Label LINE and LOAD wire

Wire labels

Help with distinguishing LINE wire from LOAD wire

Remove existing switch
Detach the remaining wires and remove The existing switch.

Turn the power back ON

Test to identify the wires

Now use a voltage tester to distinguish the wires:

Line (typically black): This wire will be powered because it carries electricity to the switch.

Load (also Typically black): This wire will NOT be powered because it carries electricity from the switch to your lights.
Identify the wires
Turn the power back Off

Connect Wemo Dimmer wires

Make sure the power is OFF before proceeding.

Remove cover plate
After detaching and removing the existing switch, snap the cover plate off of your Wemo Dimmer, and remove the sticker securing The wires.

Connect LINE and LOAD wires

Use a wire nut to connect The red LOAD wire on the Dimmer to The LOAD wire in the wall.

Use a wire nut to connect The black LINE wire on The Dimmer to The LINE wire in the wall.
Connect LINE and LOAD wires

NOTE: Your existing wires may be different colors than those shown.

Connect NEUTRAL and GROUND wires

Use a wire nut to connect the white NEUTRAL wire on the Dimmer to the NEUTRAL wires (usually white) in the wall.

Use a wire nut to connect The green GROUND wire on The Dimmer to the GROUND wires (usually green or bare copper) in The wall.
Connect NEUTRAL

NOTE: Your existing wires may be different colors than those shown.

Install Dimmer info the wall

Almost done! Tug on each wire nut to make sure they are secure on the wires.
Install Dimmer

Carefully tuck wires behind the Dimmer and insert the Dimmer inTo The box. IT could get crowded in There.
Install Dimmer

Screw the Dimmer into the wall. Be careful not to overtighten the screws.

NOTE: Before snapping on The cover plate, you’ll notice an 8-digit setup code on The dimmer. You may need this during app setup.

Finally, snap the face plate onto the Dimmer.

Turn on power

Turn on power to your Dimmer at your fuse panel or circuit breaker panel.

Physical installation is complete

The light ring on your Dimmer should blink WHITE while starting up and BLUE when ready for app setup.

BLINKING WHITE
Starting up
BLINKING BLUE
Ready for app setup

NOTE: If your Dimmer did not power up, then your load and line wires may be reversed and you need To switch Them.

Go to the app for next steps

Download and launch the Wemo App

Create a Wemo account in the app, then add your Dimmer.

Use HomeKit Code if prompted

If prompted, scan or type your Wemo’s code below. The 8- digiT number should match The code on your Dimmer (behind The faceplate).
HomeKit Code

Hang on to this guide. The code may come in handy if you ever need to set up this Wemo again

Connecting to other services

Control your Wemos with voice, create groups, and more. Connect to these services in The Wemo App
Connecting services

Got questions?

Visit wemo.com/support or call us at 1-844-745- WEMO for support.

For warranty information, go to wemo.com/warranty.

What does the light tell me?

OFF
Wemo is off.

SOLID WHITE
Wemo is on and working normally.

BLINKING WHITE
Wemo is starting up, updating firmware, or responding to your action.

BLINKING BLUE
Your Wemo is ready for setup.

GREEN
Wemo is running a rule or timer.

RED
Error or low Wi-Fi connection

WHITE/BLUE/RED: Reset your Dimmer
Press and hold the bar below the power button for reset options. Release the button when The IighT is white to restart, blue to reset Wi-Fi, and red to restore to factory settings.