nVent CADDY CA0050EG Drop In Anchor Owner’s Manual
- June 16, 2024
- nVent Caddy
Table of Contents
nVent CADDY CA0050EG Drop In Anchor
Product Information
Specifications
- Material: Steel
- Finish: Electrogalvanized
- Hole Size: 1/2
- Length: 2
- Drill Bit Diameter: 5/8
Features
- Internal thread provides easy removal and serviceability
- Installs flush or below the base surface
- Suitable for redundant non-structural systems on cracked and non-cracked concrete
- Fire resistance class R30-R120 for design of anchorages under exposure to fire
Warnings
nVent products shall be installed and used only as indicated in nVent’s
product instruction sheets and training materials. Improper installation,
misuse, misapplication, or other failure to completely follow nVent’s
instructions and warnings may cause product malfunction, property damage,
serious bodily injury and death, and/or void your warranty.
Contact Information
- Europe Netherlands: +31 800-0200135
- France: +33 800 901 793
- Germany: 800 1890272
- Other Countries: +31 13 5835404
- APAC Shanghai: +86 21 2412 1618/19
- Sydney: +61 2 9751 8500
Brands
Our powerful portfolio of brands: nVent.com
Disclaimer
nVent reserves the right to change specifications without notice.
Product Usage Instructions
Installation
- Choose a suitable location on the base surface for installation.
- Use a 5/8 drill bit to create a 1/2 hole in the base surface.
- Insert the Drop-in Anchor into the hole until it is flush with or below the base surface.
- Tighten the anchor using the internal thread for easy removal and serviceability.
Usage
The Drop-in Anchor is designed for use in both cracked and non-cracked
concrete. It can be used in redundant non-structural systems. The anchor has a
fire resistance class of R30-R120, making it suitable for design of anchorages
under exposure to fire.
FAQ
-
Q: What is the material of the Drop-in Anchor?
A: The Drop-in Anchor is made of steel. -
Q: What is the finish of the Drop-in Anchor?
A: The Drop-in Anchor has an electrogalvanized finish. -
Q: What is the recommended hole size for installation?
A: The recommended hole size is 1/2. -
Q: What is the length of the Drop-in Anchor?
A: The length of the Drop-in Anchor is 2. -
Q: What is the drill bit diameter required for installation?
A: The drill bit diameter required is 5/8.
FEATURES
- Internal thread provides easy removal and serviceability
- Installs flush or below the base surface
- Suitable for redundant non-structural systems on cracked and non-cracked concrete
- Fire resistance class R30-R120 for design of anchorages under exposure to fire
PRODUCT ATTRIBUTES
- Material: Steel
- Finish: Electrogalvanized
- Hole Size: 1/2″
- Length: 2″
- Drill Bit Diameter: 5/8
DIAGRAMS
WARNING
nVent products shall be installed and used only as indicated in nVent’s
product instruction sheets and training materials. Instruction sheets are
available at www.nvent.com and from your nVent
customer service representative. Improper installation, misuse, misapplication
or other failure to completely follow nVent’s instructions and warnings may
cause product malfunction, property damage, serious bodily injury and death
and/or void your warranty.
Europe
- Netherlands: +31 800-0200135
- France: +33 800 901 793
Europe
- Germany: 800 1890272
- Other Countries: +31 13 5835404
APAC
- Shanghai: + 86 21 2412 1618/19
- Sydney: +61 2 9751 8500
© 2023 nVent. All nVent marks and logos are owned or licensed by nVent
Services GmbH or its affiliates. All other trademarks are the property of
their respective owners.
nVent reserves the right to change specifications without notice.
References
- Building a more Sustainable and Electrified World | nVent
- Building a more Sustainable and Electrified World | nVent
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>