V I V O STAND-LIVE1M All In One Livestream Multi-Mount Floor Stand Instruction Manual
- June 16, 2024
- V I V O
Table of Contents
V I V O STAND-LIVE1M All-In-One Livestream Multi-Mount Floor Stand
Specifications
- Product Name: Mobile All-In-One Livestream Multi-Mount Floor Stand
- SKU: STAND-LIVE1M
- Weight Capacity:
- Microphone: 2.2lbs (1kg)
- Camera & Phone: 6.6lbs (3kg)
- Monitor: 11lbs (5kg)
- Laptop: 11lbs (5kg)
Package Contents
- A (x1) Adjustable Pole
- B (x1) Ring Light
- C (x1) Mic Boom
- D (x1) Laptop Tray
- E (x4) Legs
- F (x1) VESA Plate
- G (x1) Base
- H (x2) Cable Clip
- I (x2) Lower Arm
- J (x4) Upper Arm
- K (x1) Dual Connector
- L (x1) Phone/Tablet Holder
- M (x1) Mic Boom Clamp
- N (x1) Mic Mount
- O (x2) Caster
- P (x2) Locking Caster
- Q (x4) Locking Pole Ring
- R (x1) Pole Cover
- S (x2) Threaded Connector
- T (x2) Ball Head
- S-A (x3) M6x20mm Screw
- S-B (x8) M6x25mm Screw
- S-C (x4) M4x8mm Screw
- S-D (x4) M5 Washer
- M-A (x4) M4x12mm Screw
- M-B (x4) M5x12mm Screw
- M-C (x4) M5 Washer
- T-A (x1) 4mm Allen Wrench
- T-B (x1) 5mm Allen Wrench
- T-C (x1) Wrench
SKU: STAND-LIVE1M
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product. https://vivo-us.com/products
/stand-live1m
WARNING: If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TOOLS NEEDED
ASSEMBLY STEPS
STEP 1: Connect Legs (E) to Base (G) using M6x25mm Screws (S-B) and 5mm
Allen Wrench (T-B). Attach Casters (O) and Locking Casters (P) to Legs (E).
Secure assembled base to Adjustable Pole (A) using M6x20mm Screws (S-A) and
4mm Allen Wrench (T-A).
Turn the assembly over and adjust the Caster (P)
height using a Wrench (T-C). Use the side tab on Locking Casters (P) to lock
wheels in place during the assembly of the stand.
STEP 2
- Slide Cable Clip x2 (H), Locking Pole Ring x4 (Q), Lower Arm x2 (I), and Dual Connector (K) onto Adjustable Pole (A) following the order shown below.
- Tighten the set screw of the Locking Pole Ring (Q) using 4mm Allen Wrench (T-A).
Height Adjustment
Twice the Height Adjuster (A1) on Pole (A) to raise or lower the Pole. Lock
into place by tightening the set screw on the Locking Pole Ring (Q) directly
above the Height Adjuster (A1) using 4mm Allen Wrench (T-A).
Stand can now be customized as desired with mounting arms and
accessories.
The following steps give an example of how stand arms and accessories can be
mounted.
CAUTION : Properly balance the left and right weight distribution of the arms to prevent tipping.
STEP 3: Connect Upper Arm (J) to right side Lower Arm (I), then install VESA Plate (F) to Upper Arm (J). Secure by tightening set screws using 4mm Allen Wrench (T-A).
STEP 4: Attach Upper Arm (J) to left side Lower Arm (I), and secure by
tightening set screws using 4mm Allen Wrench (T-A). Insert Threaded Connector
(S) into Upper Arm (J).
STEP 5: Connect the Upper Arm (J) to the Dual Connector (K), then connect a second Upper Arm (J), as shown below. Install Threaded Connector (S) to Upper Arm (J). Secure by tightening set screws using 4mm Allen Wrench (T-A).
STEP 6: Screw Ball Head (T) onto Threaded Connector (S), then screw Ring Light (B) onto Connector.
STEP 7: Connect Mic Boom (C) to remaining mounting hole in Dual Connector
(K). Twist Mic Mount (N) onto Mic Boom (C). Optional: Mic Boom (C) can be desk
mounted using Mic Boom Clamp (M).
N
Mounting Microphone Holder
STEP 8: For VESA Plate (F), choose between a Monitor or Laptop Holder.
Laptop: Attach M4x8mm Screws (S-C) and M5 Washer (S-D) into Laptop Tray, partially protruding, using a Phillips screwdriver. Slide onto VESA Plate (F) and attach remaining M4x8mm Screws (S-C) and M5 Washers (S-D).
Optional: VESA Plate (F) can be adjusted using 4mm Allen Wrench (T-A) to allow the monitor to tilt, turn, and swivel.
STEP 9: Twist the Ball Head (T) onto the Threaded Connector (S), then
connect the Phone/Tablet Holder (L).
NOTE: Ball Head (T) can also be used to mount cameras and other multi-
media devices.
STEP 10: Remove bottom covers from Lower Arms (I) and Upper Arms (J) by sliding off. Organize cables and slide covers back on.
FAQ
-
Q: What is the weight capacity of the stand?
The weight capacity of the stand is as follows:- Microphone: 2.2lbs (1kg)
- Camera & Phone: 6.6lbs (3kg)
- Monitor: 11lbs (5kg)
- Laptop: 11lbs (5kg)
-
Q: What tools are needed for assembly?
The following tools are needed for assembly:- Phillips Screwdriver
- 4mm Allen Wrench (T-A)
- 5mm Allen Wrench (T-B)
- Wrench (T-C)
THIS PAGE INTENTIONALLY LEFT BLANK
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
Open Monday – Friday 7:00 am – 7:00 pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
-
309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com Chat live with an agent -
AVG. RESOLUTION TIME (within office hours): < 15 M
AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Mobile All-In-One Livestream Multi-Mount Floor Stand – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>