ZENTY ZT-144 Modular Matrix 4K 60Hz HDBaseT Input Card User Manual

: June 16, 2024
: ZENTY

Table of Contents

ZENTY ZT-144 Modular Matrix 4K 60Hz HDBaseT Input Card
PoC DIP Switch on HDBaseT Card
EDID Setup
PoC DIP Switch on HDBaseT Card
Warranty
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ZENTY ZT-144 Modular Matrix 4K 60Hz HDBaseT Input Card

Contact Information

Phone: 844-200-1945

Email : support@zenty.com

Specifications

Output resolution : Up to 4K 60Hz 4:2:0
Supports HDBaseT input with one HDMI loop-out
Distance : Up to 70m/220ft at 4K60(4:2:0) or 100m/330ft at 1080P over single Cat6/7
Supports RS232, bi-directional IR
PoC (Power over Cable) function

EDID Setup

Step 1 :

1. Unplug the HDBaseT input card from the Matrix Switcher chassis.

2. Adjust the 4-DIP switch settings (DIP1, DIP2, DIP3, DIP4) to the position (0,1,1,1).

3. Connect an HDMI cable from the HDMI port on the HDBaseT input card to the display, ensuring that the HDBaseT port remains connected to the transmitter.

4. Reinsert the HDBaseT input card into the matrix switcher and wait for approximately 15 seconds.

Step 2:

1. Unplug the HDBaseT input card.

2. Configure the 4-pin DIP switch (DIP1, DIP2, DIP3, DIP4) to the position (0,0,0,0).

3. Reinsert the HDBaseT input card into the matrix and disconnect the HDMI cable.

4. The EDID setup is now complete.

PoC DIP Switch on HDBaseT Card

There is a 4-pin black DIP switch on the HDBaseT card which can be used to set up the PoC function as follows:

To set PoC to 12V: Have the DIP switches A / B up and C / D down position.
To set PoC to 24V: Have the DIP switches A / C down and B / D up position.
To turn off the PoC function: Set all 4 switches to the middle position.

Maintenance

Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner, or benzine to clean.

Warranty

If your product does not work properly because of a defect in materials or workmanship, our company (referred to as the warrantor) will, for the length of the period indicated below, provide Parts and Labor (5) Years warranty from the date of original purchase. The warrantor will either repair your product with new or refurbished parts or replace it with a new or refurbished product, at their discretion.

During the Labor limited warranty period, there will be no charge for labor. During the Parts warranty period, there will be no charge for parts. You must mail-in your product during the warranty period. This Limited Warranty is extended only to the original purchaser and only covers products purchased as new. A purchase receipt or other proof of original purchase date is required for Limited Warranty service.

FAQ

Q: How far can the ZT-MIN460-BT100 extend a 4K 60Hz 4:2:0 signal?
A : The ZT-MIN460-BT100 can extend a 4K 60Hz 4:2:0 signal up to 70m or 220ft over a single Cat6/7 cable.
Q: Can the ZT-MIN460-BT100 be used with the Zenty 18×18 and 36×36 modular matrix chassis?
A: Yes, the ZT-MIN460-BT100 is compatible with the Zenty 18×18 and 36×36 modular matrix chassis.
Q: What functions does the ZT-MIN460-BT100 support?
A: The ZT-MIN460-BT100 supports bi-directional IR, RS232, local HDMI loop-out, and a DIP switch for EDID management.

Introduction

The ZT-MIN460-BT100 is a 1-card 1-port HDBaseT card which supports 4K 60Hz 4:2:0 resolution andworks with the Zenty 18×18 and 36×36 modular matrix chassis. It supports bi-directional IR, RS232,local HDMI loop-out, and a DIP switch for EDID management. Extend your 4K 60Hz 4:2:0 signal upto 70m and 1080P 60Hz signal up to 100m.

Features

Output resolution up to 4K 60Hz 4:2:0 Supports HDBaseT input with one HDMI loop-out Distance up to 70m/220ft at 4K60(4:2:0) or 100m/330ft at 1080P over single Cat6/7 Supports RS232, bi-directional IR PoC (Power over Cable) function

Specifications

EDID Setup

Step 1 :

There is no need to power off the matrix. Instead, unplug the HDBaseT input card from the MatrixSwitcher chassis. Adjust the 4-DIP switch settings (DIP1, DIP2, DIP3, DIP4) to the position (0,1,1,1).Connect an HDMI cable from the HDMI port on the HDBaseT input card to the display, ensuring thatthe HDBaseT port remains connected to the transmitter. Reinsert the HDBaseT input card into the matrix switcher and wait for approximately 15 seconds.

Step 2:

Unplug the HDBaseT input card and configure the 4-pin DIP switch (DIP1, DIP2, DIP3, DIP4) to theposition (0,0,0,0). Reinsert the HDBaseT input card into the matrix and disconnect the HDMI cable. The EDIDsetup is now complete.

PoC DIP Switch on HDBaseT Card

There is a 4-pin black DIP switch on the HDBaseT card which can be used to set up the PoC fucntion as12V, 24V, and PoC function off.

To set PoC to 12V, have the DIP switches A / B up and C / D to down position.
To set PoC to 24V, have the DIP switches A / C down and B / D to up position.
To turn off the PoC function, set the 4 switches to the middle position.

Maintenance
Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner, or benzine to clean.
6.
Warranty
If your product does not work properly because of a defect in materials of workmanship, our company(referred to as “the warrantor”) will, for the length of the period indicated as below, “Parts and Labor(5) Years”, which starts with the date of original purchase (“Limited Warranty period”), at its optioneither (a) repair your product with new or refurbished parts, or (b) replace it with a new or a refurbishedproduct. The decision to repair or replace will be made by the warrantor.
During the “Labor” limited warranty period, there will be no charge for labor. During the “Parts”warranty period, there will be no charge for parts. You must mail-in your product during the warrantyperiod. This Limited Warranty is extended only to the original purchaser and only covers productspurchased as new. A purchase receipt or other proof of original purchase date is required for LimitedWarranty service.

Mail-In Service

When shipping the unit, carefully pack and send it prepaid, adequately insured, and preferably in theoriginal carton. Include a letter detailing the complaint and provide a daytime phone and/or email address where you can be reached phone and/or email address where you can be reached.

Warranty

Limited Warranty Limits and Exclusions

This Limited Warranty ONLY COVERS failures due to defects in material or workmanship and DOES NOT COVER normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT COVER damages that occurred in shipment, or failures that are caused by
products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, miss-adjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, or service by anyone other than a Factory Service Center or other Authorized Servicer, or damage that is attributed to acts of God.
There are no express warranties except as listed under “Limited Warranty Coverage”. The warrantor is not liable for incidental or consequential damages resulting from the use of this product or arising out of any breach of this warranty. (As examples, this excludes damages for lost time, cost of having someone move or re-install an installed unit if applicable, travel to and from the service, loss of or damage to media or images, data or other recorded content. The items listed are not exclusive but are for illustration only). Parts and services, which are not covered by this limited warranty, are your responsibility.