American Blinds Prestige 1 3/16 Inch Custom Modern Metal Drapery Hardware Instruction Manual

American Blinds Prestige 1 3/16 Inch Custom Modern Metal Drapery Hardware

Product Information

The Modern Metal Drapery Hardware is a set of brackets, poles, rings, and finials designed for installing drapery in a modern style. The hardware is made of durable metal and is available in various finishes. The set includes two types of brackets: IRATI Bracket and FRENCH RETURN Bracket. The hardware is easy to install and provides a secure and stylish solution for hanging drapes.

• IRATI Bracket
  The IRATI Bracket is used for standard installations and provides a sleek and minimalist look. It consists of a backplate and a bracket that can be assembled together. The bracket opening can be adjusted vertically for proper alignment. The top of the bracket will rise 1 inch above the pole.

• FRENCH RETURN Bracket:
  The FRENCH RETURN Bracket is used for installations where the drapes need to return to the wall. It also includes a decorative base plate cover for an added aesthetic touch. The top of the bracket’s decorative base plate cover will rise 1 inch above the pole.

• Optional Splice:
  If your drapery pole set is longer than 96 inches, it will come as two separate poles. In this case, a center bracket must be used on the splice where the poles meet for additional support.

Product Usage Instructions:

Installing IRATI Bracket:

1. Read through all instructions carefully before starting installation.
2. Unpack all materials and ensure all components are included.
3. Mark the desired height for the top of the drapery pole installation.
4. Mount the backplate of the bracket at a height 1 1/2 inches higher than the mark.
5. Securely attach the backplate to the mounting surface using screws.
6. Assemble the bracket onto the backplate by screwing it clockwise until tight.
7. Adjust the bracket opening to be vertical if necessary.
8. Tighten the small hex to adjust and tighten the bracket.
9. Repeat steps 3-8 for all other brackets, evenly spacing them between the two installed brackets.
10. Slide rings onto the pole, leaving one ring on the outside of each end bracket if desired.
11. Insert the pole through the bracket openings.
12. Tighten the set screws on the brackets to secure the pole.
13. Attach finials to both ends of the pole and tighten the set screws on the finials to secure them.

Installing FRENCH RETURN Bracket:

1. Read through all instructions carefully before starting installation.
2. Unpack all materials and ensure all components are included.
3. Mark the desired height for the top of the drapery pole installation.
4. Mount the backplate of the bracket at a height 1 1/2 inches higher than the mark.
5. Securely attach the backplate to the mounting surface using screws.
6. Place the decorative base plate cover onto the stem of each backplate.
7. Repeat steps 3-6 for all other brackets, evenly spacing them between the two installed brackets.
8. Slide rings onto the pole, leaving one ring on the outside of each end bracket if desired.
9. Insert the pole through the bracket openings.
10. Tighten the set screws on the brackets to secure the pole.
11. Attach finials to both ends of the pole and tighten the set screws on the finials to secure them.

Installing Optional Splice:
If your drapery pole set is longer than 96 inches:

1. Use two separate poles for the installation.
2. Install a center bracket at the splice where the poles meet for additional support.

Getting Started:

• Please read through all instructions carefully before you begin installation.
• Unpack all materials making sure all components are included:
  • Pole(s)
  • Drapery rings
  • Finials
  • Mounting brackets
  • Splice, if needed
    Please note that your brackets must be securely attached to the mounting surface. If your screws do not hit wood studs you’ll have to use a different fastener, which can be found at any local hardware store.

Tools You Will Need

• Drill with a 1/8” bit and a Phillips bit
• Phillips screwdriver
• Metal tape measure

Installing Your Drapery Hardware

IRATI Bracket

DIMENSION

Mark
Mark the height you would like the top of drapery pole to be installed. The center of your bracket should be mounted 1 1/2” higher than that mark.

Mount

• Measure the width of the track. Mark the placement of the two end brackets at the height determined in step 1, approximately 3” – 4” in from the ends of where the track will be installed.
• Take the backplate off the bracket and place the center of the backplate at marked height. (remove backplate from the bracket by rotating plate counter clockwise).

Assemble Bracket
Reassemble the bracket onto the backplate. Screw bracket clockwise onto backplate. Turn until tight. Make sure bracket opening is vertical (loosen small hex to adjust and tighten once complete).

Attach Rings and Poles
Slide rings onto pole, you may want to leave one ring on the outside of each of the end brackets. Insert pole through bracket

Attach Finials
Attach finials to both ends of the pole. Tighten set screws on finials to secure to pole.

Installing Your Drapery Hardware

FRENCH RETURN Bracket

Mark
Mark the height you would like the top of drapery pole to be installed. The center of your bracket should be mounted 1 1/2” higher than that mark.

Mount

• Measure the width of the track. Mark the placement of the two end brackets at the height determined in step 1, approximately 3” – 4” in from the ends of where the track will be installed.
• Take the backplate off the bracket and place the center of the backplate at marked height. (remove backplate from the bracket by rotating plate counter clockwise).
• Drill in screws through each hole for a secure mount. Repeat this process for all other brackets evenly spacing them between the two installed brackets.
• Place decorative base plate cover onto stem of each backplate.
  NOTE: The top of the bracket’s decorative base plate cover will rise 1” above the pole.

Assemble Bracket

• Place French Returns and rings onto poles prior to attaching brackets and French Returns to baseplates. Loosen set screws on French
• Returns prior to attachment.
• French Returns – Make sure French Return is attached to pole with splice as seen in image below.
• Rings – Make sure that rings are split evenly on either side of or in between brackets.
• Tighten set screws onto French Returns to secure hold.

Installing Your Drapery Hardware

OPTIONAL Splice

• All pole sets over 96” will come as 2 poles. A center bracket must be used on the splice where the poles meet.
• All poles sets over 96” will come as 2 poles.
  • Insert splice into open end of each pole.
  • Evenly distribute the depth of the splice into each pole.
  • Place middle bracket over splice location.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>