ZENTY ZT-130 Modular Matrix 4K 30Hz HD BaseT Input Card User Manual
- June 12, 2024
- ZENTY
Table of Contents
ZENTY ZT-130 Modular Matrix 4K 30Hz HD BaseT Input Card
Product Information
- Zenty Professional A/V Solution Provider
- Phone : 844-200-1945
- Email : sales@zenty.com
- Address : 9807 Emily Lane, Stafford, TX 77477
This product is a 1-card 1-port 4K30 HDBaseT input card designed to be used with Zenty chassis models including 9×9, 16×16, 18×18, and 36×36. It supports HDMI loop out and can be used for EDID management by using the DIP switch on the card. The card also supports bi-directional IR and RS232 transmission. It utilizes HDBaseT technology, allowing it to provide power over cable (POC) for HDBaseT transmitters. The maximum distance supported is up to 230ft. (70m) for 4K30 or 330ft. (100m) for 1080P.
Introduction
This is a 1-card 1-port 4K30 HDBaseT input card which is to be used with Zenty
chassis, including 9×9, 16×16, 18×18 and 36×36. It supports HDMI loop out or
this HDMI loop can be used for the EDID management function by working with
the DIP switch on the card. It also supports bi directional IR and the R$232
transmission. It uses HDBaseT technology so it can support POC for the HDBaseT
transmitters. The distance can up to 230ft. (70m) for 4K30 or 330ft. (100m)
for 1080P.
Features
- Output resolution up to 4K30
- Supports HDBaseT input with one HDMI loop out Distance up to 70m/220ft at 4K30 or 100m/330ft at 1080P over single Cat6/7
- Supports RS232, bi-directional IR
- PoC (Power over Cable) function
Specifications
Audio and Video
Inputs| 1 x HDBaseT In: RJ-45
Outputs| 1 x HDMI In: 19-pin Type-A
EDID| 4-Pin Dip Switch for internal EDID or simulating
from the display
Latency| 15 – 30ms
Audio Formats| 2ch PCM. DTS-HD Master, TrueHD
Video Resolutions and Cable Distances| 720P 60Hz 12-bit: Up to 330ft. / 100m
10800P 30Hz 12-bit: Up to 330ft. / 100m
| 1080P 60Hz 12-bit: Up to 330ft. / 100m
2160P 20Hz 8-bit: Up to 220ft. / 70m
---|---
Standards / Protocol| HDCP 1.4
Maximum Pixel Clock| HDMI: 296Mhz
Communication and Protocol
HDBaseT| HDMI, HDCP 1.4, EDID, PoH / PoC, Bi-
directional IR, RS232
IR| 1 x IR RX (3.5mm), 1 x IR TX (3.5mm)
RS232| 3-Pin phoenix connector
Power
Power Supply| Internal to / from matrix
EDID Setup
Step 1:
No need to turn off the matrix. Unplug the HDBaseT input card from the Matrix
Switcher chassis, and have the 4-DIP switch (DIP1, DIP2, DIP3, DIP4) set up to
position (0,1, 1, 1). Have an HDMI cable connected to the display from HDMI
port on the HDBaseT input card, The HDBaseT port can stay connected to the
transmitter.
Insert the HDBaseT input card back to the matrix switcher, and wait for about
15 seconds.
Step 2:
Plug out the HDBaseT input card and have the 4-pin DIP switch (DIP1, DIP2,
DIP3, DIP4) set up to position (0,0,0,0). Then insert the HDBaseT input card
back to the matrix and disconnect the HDMI cable. EDID setup is
finished.
- There’s a 4-pin black DIP on the HDBaseT card, it’s able to set up the POC function as 12V, 24V, and POC function off.
- Set POC to 12V: Have the DIP switch A & B up, and the C & D to down position.
- Set POC to 24V: Have the DIP switch A & C down, and the B & D to up position.
Maintenance
- Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner, or benzene to clean.
Warranty
- If your product does not work properly because of a defect in materials of workmanship, our company (referred to as “the warrantor”) will, for the length of the period indicated as below, “Parts and Labor (5) Years”, which starts with the date of original purchase (“Limited Warranty period*), at its option either (a) repair your product with new or refurbished parts, or (b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the warrantor.
- During the “Labor” limited warranty period, there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. You must mail in your product during the warranty period. This Limited Warranty is extended only to the original purchaser and only covers products purchased as new. A purchase receipt or other proof of the original purchase date is required for Limited Warranty service.
Mail-In Service
- When shipping the unit, carefully pack and send it prepaid, adequately insured, and preferably in the original carton. Include a letter detailing the complaint and provide a daytime phone and or email address where you can be reached.
Limited Warranty Limits and Exclusions
- This Limited Warranty ONLY COVERS failures due to defects in material or workmanship and DOES NOT COVER normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, setup adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, or service by anyone other than a Factory Service Center or other Authorized Servicer, or damage that is attributed to acts of God.
- THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE” THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someone remove or re-install an installed unit if applicable, travel to and from the service, and loss of or damage to media or images, data or other recorded content. The items listed are not exclusive, but are for illustration only.) PARTS AND SERVICES, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.
WWW.ZENTY.COM
9807 EMILY LANE
STAFFORD, TX 77477
844-200-1945
SUPPORT@ZENTY.COM
SALES@ZENTY.COM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>