New Bee BH60 Wireless Office Headset User Manual

New Bee BH60 Wireless Office Headset

PRODUCT INFORMATION

Product Diagram

Button Function Description

hanging up,
redialing, rejecting a call, activating voice assistant, and
restoring factory settings

Bluetooth Transmitter Button

headset. Double-click again to reconnect the transmitter and
headset. Press and hold for 3 seconds to restore factory
settings.

LED Indicator

Headset LED Indicator

Bluetooth Transmitter LED Indicator

Flashing blue for 3 times, then turns into red and blue
flashing alternately| Restore Factory Settings

Connect to Computer

1. Turn on the headset and make it enter pairing mode by keeping the headset LED indicator flashing in red and blue alternately.
2. Plug the Bluetooth transmitter into the USB port of the computer. The Bluetooth transmitter LED indicator will start flashing in red and blue and it will automatically search and connect to the headset. When you hear the voice prompt “connected”, it means the connection is successful.
3. After the connection is successful, the headset LED indicator will flash blue every 30 seconds and the Bluetooth transmitter LED indicator will be solid blue.

Microphone Mute
To mute the microphone during a call or while using the headset, refer to the device-specific instructions or settings.

Charge The Headset
Follow these steps to charge the headset:

1. Connect the charging cable to the headset’s charging port.
2. Connect the other end of the charging cable to a power source.
3. The headset LED indicator will turn solid red while charging. It will turn solid blue when fully charged.

Common Problems
If you encounter any issues while using the BH60 Wireless Office Headset, refer to the troubleshooting section in the user manual for possible solutions.

Safety Notes
Read and follow the safety instructions provided in the user manual to ensure safe usage of the BH60 Wireless Office Headset.

Product Diagram

1. Volume Up Button
2. Multifunctional Button
3. Volume Down Button
4. Power Button / LED Indicator
5. Charging Port

Button Function Description

LED Indicator

Connect to Computer

• Step 1: Turn on the headset and make it enter pairing mode, the headset LED indicator keeps flashing in red and blue alternately.

• Step 2: Plug the Bluetooth transmitter into the USB port of computer. The Bluetooth transmitter LED indicator keeps flashing in red and blue and it will automatically search and connect to the headset. When hearing the voice prompt ‘connected’ , it means the connection is successful.

• Step 3: After the connection is successful, the headset LED indicator flashes blue every 30 seconds and the Bluetooth transmitter LED indicator is solid blue.
  NOTE：

1. The headset can’t connect to two devices at the same time. When both the cellphone and the transmitter have connection records, the cellphone will be connected first after the headset is turned on. If you want to connect the transmitter, please turn off the Bluetooth function of cellphone first.
2. If the device does not work normally after the connection is successful, please check whether the sound settings of the device are selected correctly. Operation Steps: Open the ‘sound settings’ of the device, find ‘Playback and Recording Devices’, and select ‘BTD-Q2’. If there are multiple enabled devices ( Windows system ), please set all other audio devices to the disabled state except the device ‘BTD-Q2’.

Connect to Cellphone

• Step 1: Turn on the headset and make it enter pairing mode, the headset LED indicator keeps flashing in red and blue alternately.

• Step 2： Open the Bluetooth function of cellphone, find “BH60” and click to connect. When hearing the voice prompt ‘connected’ , it means the connection is successful.

NOTE：
The headset can’t connect to two devices at the same time. Before the headset connects to the cellphone for the first time, please ensure that the headset is disconnected from the transmitter if there is a connection record between the headset and the transmitter.

Microphone Mute

1. Mute On ( Figure 1 )
   Rotate the microphone boom upward and the microphone mute function is turned on.

2. Mute Off ( Figure 2 )
   Rotate the microphone boom downward and the microphone mute function will be turned off. At this time, the voice content output is normal.

Charge The Headset

Charge the headset with USB cable
When the headset is charging, the red light is on. When the headset is fully charged, the blue light is on.

Common Problems

1. Low battery may cause disconnection, in order not to affect normal use, please charge the headset in time.
2. If the headset fails to turn on, please try to charge it up first, and turn it on after fully charged.
3. If the battery runs out or has not been used for a long time, there may be no signal lights at the beginning of charging, but the indicator will normally light up in red after a few minutes.
4. No Sound from the headset:
   • Make sure the headset connects to the electronic device successfully.
   • Make sure that the effective distance between the headset and the device is less than 10 meters.
   • Make sure you choose this Bluetooth device for music playback.
   • Make sure your electronic device is within a range of strong signal without external interference.
   • Check whether your electronic device has been connected to other Bluetooth devices.
5. The model of this headset can not be searched.
   • Make sure the headset is in the pairing mode you want (Cellphone /Bluetooth Transmitter)
   • There may be a program error on the headset and device.Please reset the headset and Bluetooth transmitter.
6. No sound can be heard from the headset when in a call
   • Make sure your headset and device are connected successfully.
   • Make sure the call is selected in the state of the Bluetooth device.

Safety Notes

1. Please use original accessories provided for this product, otherwise, it may cause low performance, headset damage, or a short circuit, and all of these are out of our warranty support.
2. Disassembling personally may damage the headset and this is not covered by warranty.
3. The headset is not waterproof. Do not use it in a humid or dusty environment.
4. Please clean the headset with a clean, soft, and dry cloth.
5. Do not place the product in an extreme environment, otherwise, it may be temporarily unavailable for use. The normal use temperature is -5°C to 45°C.

FCC Warning Statement

• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
  • This device may not cause harmful interference, and
  • this device must accept any interference received, including interference that may cause undesired operation.
• The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

ISED Canada Statement

• This device contains licence-exempt trasnsmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
• Canada ‘s licence-exempt RSS(s). Operation is subject to the following two conditions:
  1. this device may not cause interference and
  2. this device must accept any interference, including interference that may cause undesired operation of the device. Radiation Exposure: This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment

RF Exposure Statement

To maintain compliance with IC’s RF Exposure guidelines, The installation and operation of the device should meet the requirements for portable devices. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter

Happy?

• Thank you for choosing our products! We sincerely hope it will be your new-found happiness.
• If you are fully satisfied with your using experience, could you please kindly share to your friends?
• We also engage with our fans to learn how we can do better by offering free pre-release products. If you are interested, do not hesitate to follow us on

Not Happy?
lf you have any questions, concerns, or just not satisfied with our products, please feel free to contact us through e-mail at:

• E-mail: [email protected]
• Tel:
  • （USA） 1-626-701-7623
  • （UK） 07845854035
• Address: 3rd Fl, Bldg E, Guanghao Ind., No. 23, Yunfeng Rd, Dalang St., Longhua Dist., Shenzhen City, Guangdong Prov., China

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>