QualGear QG-TM-092-BLK Heavy Duty Full Motion TV Wall Mount Instruction Manual

QualGear QG-TM-092-BLK Heavy Duty Full Motion TV Wall Mount

Specifications

• Model: QG-TM-092-BLK
• Product: Heavy Duty Full Motion TV Wall Mount
• Supported TV Sizes: Most 60 to 100 Flat Panel and Curved TVs
• Maximum Weight Capacity: 80kg (176lbs)
• Supported VESA Patterns: 200×200|300×200|300×300|400×200|400×300|400×400 600×200|600×300|600×400|800×200|800×300|800×400 800×600|900×200|900×300|900×400|900×600
• Version: October 2017

Installation Instructions

1. Before starting the installation, read the entire installation manual and ensure that all parts are included.
2. Ensure that you have good mechanical aptitude, experience with basic building construction, and fully understand the instructions.
3. Make sure to install the product as specified in the manual. Improper installation may cause damage or serious injury.
4. Tighten the screws firmly, but do not over-tighten as it can damage the items and reduce their holding power.
5. This product is designed for indoor use only. Outdoor use voids the limited warranty.
6. This product is intended for residential use only. Commercial use voids the limited warranty. Visit http://www.qualgear.com/warranty.php for warranty information.
7. If mounting to wooden studs, ensure that mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud finder is highly recommended.
8. Never exceed the maximum rated weight specified in the manual.
9. Ensure that the supporting surface can safely support the combined load of the equipment and all attached hardware and components.
10. Use an assistant or mechanical lifting equipment to safely lift and position the equipment.
11. Avoid installing near-air conditioner vents or areas with excessive dust or smoke.
12. Take care of electrical cables, water, or gas pipes in the wall when drilling holes.
13. This product is designed to be installed on the following wall constructions: Wooden Studs, Wooden Beams, Solid Concrete, and others.

Parts Checklist

IMPORTANT : Before starting installation, please check that all parts shown in this checklist are included. If any parts are missing or damaged, contact your local distributor or support@qualgear.com for replacement parts and do not start assembly and installation until you receive all the parts.

Hardware Package

Mounting to a Wooden Stud Wall

NOTE: For concrete wall mounting, follow Step 1b.

1. Using an edge-to-edge stud finder, find the edges of the stud.
2. Using a level, mark the centerline of the stud.
3. Using the marking template (F) provided, mark two holes for drilling on the centerline of the stud.
4. Using a power drill and 1/4″ drill bit, drill pilot holes of 1/4″ ( 6 mm) diameter and at least 3.5″ (90 mm) depth.
5. Insert two lag bolts (W-A) at the top drilled holes and tighten with a socket wrench, leaving a 5mm space from the wall.
6. Lift the wall mount and place against the wall, align the keyholes of the wall plate with the lag bolt heads, so the wall plate sits on the 5mm space. Then use the wall plate as a template, mark two bottom holes for drilling.
7. Remove the wall mount from the wall and drill the bottom holes according to step 4. Then place the wall mount onto the wall again as directed from step 6. Insert the two lag bolts (W-A) and D8 washers (W-C) through the lower mounting holes. Tighten all screws using a socket wrench.

NOTE Do NOT use a power drill and do NOT over-tighten the lag bolts.

WARNING

• Make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
• Installers are responsible for providing hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

Mounting to a Concrete or Brick Wall

1. Hold the marking template (F) provided against the wall where you want to install the TV, and mark four holes for drilling.
2. Using a power drill and a 1/2″ masonry drill bit, drill mounting holes of 1/2″ (12 mm) diameter and 3.7″ (95 mm) depth at the marked locations in the previous step.
3. Place concrete anchors (W-B) in each hole.Tap each anchor flush with the wall using a hammer. Insert and tighten the top two lag bolts leaving a 5mm space from the wall.

NOTE Do NOT use a power drill and do NOT over-tighten the top two lag bolts.

• Align the top holes on the wall mount with the bolt heads on the wall, then lower the wall plate gently so the bolt heads is supporting the wall mount. Then install both lag bolts (W-A) and D8 washers (W-C) through the lower mounting holes and into the concrete anchors to secure the wall mount.

WARNING: Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

Removing the Screws from the Adapter Brackets

Installing to a Flat Back Panel

IMPORTANT! Tighten all screws but do NOT over tighten Choose the appropriate screws and washers according to the type of your TV, and attach adapter brackets (B) to the back of the TV using a Phillips screwdriver.

Installing to a Curved or Recessed Back Panel

Choose appropriate screws, washers, and spacers (if necessary) according to the type of your TV, attach the adapter brackets (B) to the back of the TV, then tighten screws using a Phillips screwdriver.

Hanging the TV onto the Wall Mount

IMPORTANT!: Tighten all screws but do NOT over tighten
NOTE Hold TV securely until all screws are firmly installed before releasing the TV.

Cable Management

Attach the cable clips to the arm using the appropriate screws. Tighten all screws using a proper Phillips screwdriver.

Run the cables through the cable clips.

Adjustments

Maintenance

Please check that the wall mount is secure and safe to use at regular intervals. If you have any questions regarding any of the instructions or warnings; please contact your local distributor (OR) contact QualGear technical support via email at support@qualgear.com

NOTE: Please read the entire installation manual. Check to ensure that all parts are included before you start installation and assembly.

WARNING

• Do not begin to install your QualGear product until you have read and understood all the instructions and warnings contained in this installation manual.

• US customers with questions regarding instructions, please contact QualGear customer support via email at support@qualgear.com. For all international customers, please contact your local distributor.

• This product should only be installed by someone of good mechanical aptitude, who has experience with basic building construction, and who fully understands these instructions.

• This product was designed to be installed and utilized only as specified in this manual. Improper installation of this product may cause damage or serious injury. QualGear is not liable for the improper use or installation of its products.

• Make sure that the supporting surface
  will safely support the combined load of the equipment and all attached hardware and components.

• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.

•  Tighten screws firmly, but do not over-tighten. Over-tightening can damage the items, greatly reducing their holding power.

• All QualGear products are intended for indoor use only and any outdoor use voids the limited warranty.

• All QualGear products are designed and tested for residential use only and any commercial use voids the limited warranty. For warranty information, please visit
  http://www.qualgear.com/warranty.php.

• If mounting to wooden studs, make sure that mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud finder is highly recommended.

• Never exceed the maximum rated weight specified in this manual.

• All bolts and screws must be used at the designated points in the installation instructions to prevent property damage and/or personal injury.

• DO NOT install near air conditioner vents or where there is excessive dust or smoke.

• When drilling holes in the wall, it is very important to take care of electrical cables, water, or gas pipes in the wall.

• This product was designed to be installed on the following wall construction only:

WALL CONSTRUCTION

• Wooden Stud
• Wooden Beam
• Solid Concrete
• Other

HARDWARE REQUIRED

• Included
• Included
• Included
• Contact Qualified Professional

FAQ

• Q: Can I use this product for outdoor installations?
• A: No, this product is designed for indoor use only. Outdoor use voids the limited warranty.
• Q: Can I use this product for commercial purposes?
• A: No, this product is designed and tested for residential use only. Commercial use voids the limited warranty. Visit http://www.qualgear.com/warranty.php for warranty information.
• Q: How do I ensure that I don’t exceed the maximum weight capacity?
• A: Make sure to check the weight of your TV and ensure it does not exceed the maximum weight capacity specified in the manual.
• Q: Can I mount this product on any type of wall?
• A: This product is designed to be installed on wooden studs, wooden beams, solid concrete, or other suitable wall constructions as specified in the manual.
• Q: What should I do if any parts are missing?
• A: Please ensure that all parts are included before starting the installation. If any parts are missing, please contact QualGear customer support via email at support@qualgear.com for assistance.

QR SCAN

Scan the QR Code™ below for more info about this product:

For Most 60″ to 100″ Flat Panel and Curved TVs
CAUTION: Do not exceed the maximum rated weight specified. Otherwise, serious injury or property damage may occur.

Warranty

1 Year Limited Warranty
Version October 2017

References

• QualGear Warranty On Product Purchase | Qualgear Warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>