V I V O STAND-V004TG Quad Monitor Desk Stand Instruction Manual
- June 16, 2024
- V I V O
Table of Contents
V I V O STAND-V004TG Quad Monitor Desk Stand
Product Information
- Product Name: Quad Monitor Desk Stand
- SKU: STAND-V004TG
- Manufacturer: Vivo
- Website: https://vivo-us.com/products/stand-v004tg.
Specifications
- Weight Capacity: 22 lbs (10 kg) per arm
- Package Contents:
- Pole (x1)
- Glass Base (x1)
- Monitor Arm (x1)
- Monitor Bracket (x1)
- Decorative Cover (x1)
- Rubber Feet (x6)
- Soft Pad (x1)
- Spare Plastic Cover (x2)
- Side VESA Plate (x2)
- Center VESA Plate (x2)
- M8x8mm Screw (x3)
- M8 Washer (x3)
- M8x10mm Screw (x2)
- M6x10mm Screw (x3)
- M4x6mm Screw (x1)
- Security Nut (x2)
- M4x12mm Screw (x12)
- 4mm Allen Wrench (x1)
- 5mm Allen Wrench (x1)
- M4x30mm Screw (x12)
- M4 Spacer (x12)
- 3mm Allen Wrench (x1)
- 6mm Allen Wrench (x1)
- Wrench (x1)
- Tools Needed: Phillips Screwdriver
Product Usage Instructions
Step 1: Assembly
- Attach the Rubber Feet (F) to the underside of the Glass Base (B).
- Attach the Soft Pad (E) to the Pole (A) by poking holes through the Pad with a screwdriver.
- Install the Pole (A) to the Glass Base (B) using the M6x10mm Screws (S-D), M8x8 mm Screws (S-A), M8 Washers (S-B), and a Phillips screwdriver.
- Slide the Decorative Cover (D) over the Pole (A).
Step 2: Attaching Monitor Arm
- Install the Monitor Arm (C) and Monitor Bracket (D) to the Pole (A) using the M8x10mm Screws (S-C) and 5mm Allen Wrench (T-C).
Step 3a: Attaching Flat Back Monitors
- Attach the Center VESA Plates (J) to the monitors you intend to mount in the center of the mount.
- Attach the Side VESA Plates (I) to the remaining monitors.
- Secure the plates using the M4x12mm Screws (M-A). Hand-tighten screws to avoid stripping the plastic screw heads.
Step 3b: Attaching Curved/Recessed Back Monitors
- Attach the Center VESA Plates (J) to the monitors you intend to mount in the center of the mount.
- Attach the Side VESA Plates (I) to the remaining monitors.
- Secure the plates using the M4 Spacers (M-C), M4x30mm Screws (M-B), and a Phillips screwdriver.
Step 4: Mounting Monitors
- Slide the center monitor onto the Center Head (C1) of the Monitor Arm (C).
- Secure the monitor using the M4x6mm Screw (S-E).
Step 5: Attaching Outer Monitors
- Slide the outer monitors onto the Outer VESA Heads (C2).
- Secure the monitors with Cap Nuts (S-F).
Adjusting Monitor Tilt
- Pry off the Plastic Covers (C3) from the Outer VESA Heads (C2).
- Tighten or loosen the exposed nut on the side using the Wrench (T-E) to adjust the tilt.
- Replace the Plastic Covers (C3).
Adjusting Monitor Height
- To adjust the center monitor’s height, turn the screw behind the Center Head (C1) and Monitor Bracket (D) using the 5mm Allen Wrench (T-B).
- To level the side monitors, remove the Cap Nut (S-F) and turn the inner bolt with the 3mm Allen Wrench (T-A) to raise or lower the monitor.
- Replace the Cap Nut after adjustment.
FAQ
-
Q: What is the weight capacity of this desk stand?
A: The weight capacity is 22 lbs (10 kg) per arm. -
Q: What tools are needed for assembly?
A: You will need a Phillips Screwdriver. -
Q: How can I adjust the tilt of the monitors?
A: Pry off the Plastic Covers from the Outer VESA Heads and tighten or loosen the exposed nut on the side using the provided Wrench. -
Q: How do I adjust the height of the monitors?
A: Use the provided Allen Wrenches to turn the screws behind the Center Head and Monitor Bracket for the center monitor, and use the Allen Wrench to turn the inner bolt for the side monitors.
SKU: STAND-V004TG
Scan the QR code with your mobile device or follow the link for helpful
videos and specifications related to this product.
https://vivo-us.com/products/stand-v004tg.
GET IN TOUCH | Monday-Friday from 7:00 am-7:00 pm CST
- help@vivo-us.com
- www.vivo-us.com Chat live with an agent!
- 309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
TIP OVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD OR BACKWARD.
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
THE USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Attach Rubber Feet (F) to the underside of the Glass Base (B). Attach Soft Pad
(E) to the Pole (A). Use a screwdriver to poke holes for screws through the
Pad.
Install Pole (A) to Glass Base (B) using M6x10mm Screws (S-D), M8x8mm Screws (S-A), M8 Washers (S-B), 4mm Allen Wrench (T-B), and a Phillips screwdriver. Slide Decorative Cover (D) over the Pole.
STEP 2
Install Monitor Arm (C) and Monitor Bracket (D) to the Pole (A). Secure using
M8x10mm Screws (S-C) and 5mm Allen Wrench (T-C).
STEP 3a – Flat Back Monitors
- Attach the Center VESA Plates (J) to the monitors you intend to mount in the center of the mount. Attach Side VESA Plates (I) to remaining monitors. Secure using M4x12mm Screws (M-A).
- NOTE: Hand-tighten screws to avoid stripping the plastic screw heads.
STEP 3b – Curved/Recessed Back Monitors
Attach the Center VESA Plates (J) to the monitors you intend to mount in the
center of the mount. Attach Side VESA Plates (I) to remaining monitors. Secure
using M4 Spacers (M-C), M4x30mm Screws (M-B) and a Phillips screwdriver.
STEP 4
Slide the center monitor onto the Center Head (C1) of the Monitor Arm (C).
Install the M4x6mm (S-E) to secure the monitor.
STEP 6
Slide the outer monitors onto Outer VESA Heads (C2). Secure with Cap Nut
(S-F).
Adjust Monitor Tilt
Pry off Plastic Covers (C3) from the Outer VESA Heads (C2). The exposed nut on the side is used to adjust the tilt. Tighten the nut using a Wrench (T-E) to adjust. Replace Plastic Covers (C3).
To adjust the center monitor to swivel or tilt, use 3mm Allen Wrench (T-A) to loosen the center set screw on the Center Head (C1) and Monitor Bracket (D) as shown at the left.
Adjust Monitor Height
To adjust the center monitor height, turn the screw behind Center Head (C1) and Mount Bracket (D) using the 5mm Allen Wrench (T-B). To level the side monitors, remove the Cap Nut (S-F) and turn the inner bolt with the 3mm Allen Wrench (T-A) to raise or lower the monitor. Replace the Nut after the adjustment.
To adjust swivel joint tension, remove the Monitor Arm Cover and turn the bolt underneath with the 6mm Allen Wrench (T-D).
Cable Management
Manage cables using Wire Clips (C4) on Arm (C). Remove the split cap from the Pole (A) and feed cables through, pulling ends out from the opening in the back. Replace the split cap when finished.
- Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
Open Monday – Friday 7:00 am – 7:00 pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
- 309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
- www.vivo-us.com Chat live with an agent! AVG. RESOLUTION TIME (within office hours): < 15 M
- help@vivo-us.com
- AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com.
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Quad Monitor Desk Stand – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>