V I V O STAND-V104A Quad LED LCD Computer Monitor Heavy Duty Desk Mount Instruction Manual
- June 16, 2024
- V I V O
Table of Contents
V I V O STAND-V104A Quad LED LCD Computer Monitor Heavy Duty Desk Mount
Instruction Manual
ASSUMBLY INSTRUCTION
SKU: STAND-V104A
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product. Instruction Manual
https://vivo-us.com/products/stand-v104a
WARNING
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER
WARNING: CHOKING HAZARD
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TOOLS NEEDED
Phillips Screwdriver
Drill
PACKAGE CONTENTS
A (x1) Pole
| **B (x1) Clamp
| C (x1) Clamp Brace
| D (x1) Decorative Cover
---|---|---|---
E (x1) Center Monitor Arm
| F (x2) Monitor Arm
| G (x1)
Mount
| H (x1) Support Plate
I (x1) Foam Pad
| J (x4) Monitor Arm Cover
| K (x2) Spare Cap
| L (x4) Plastic Spacer
M (x4) Cable Clip| N (x2) Side VESA Plate
| O (x2) Center VESA Plate
**|
S-A (x2) M10x47mm Screw| **S-B (x1) M10x100mm Screw
| S-C (x3) M6x10mm Screw
| S-D (x2) M10x15mm Screw
---|---|---|---
S-E (x4) M8x10mm Screw
| S-F (x2) Nut
| S-G (x2) M4x6mm Screw
| S-H (x1) Spring Washer
S-I (x1) M10 Washer
| M-A (x16) M4x12mm Thumbscrew
| M-B (x16) M4x30mm Screw
| M-C (x16) M4 Spacer
T-A (x1) 3mm Allen Wrench| T-B (x1) 5mm Allen Wrench| T-C (x1)
6mm Allen Wrench| T-D (x1) Wrench**
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
ASSEMBLY STEPS
STEP 1 – Clamp Installation
Install Pole (A) to Clamp Brace (C) using M6x10mm Screws (S-C) and a Phillips screwdriver.
—————————————————————————————————————————-
Assemble Clamp (B) to Clamp Brace (C) using M10x15mm Screws (S-D)
and 6mm Allen Wrench (T-B). Secure the clamp assembly to the desktop be
tightening to the hand bolts on Clamp (B). Install the Pole Cover (D)
to Pole (A).
STEP 1 – Grommet Installation
Remove adhesive backing from Foam Pad Pad (I) and place on the bottom of Pole
(A). 
—————————————————————————————————————————-
Install Pole (A) existing grommet hole using Support Plate (H) with
M10x100mm Screw (S-B) , M10 Washer (S-I) and Spring Washer (S-H).
Tighten with Wrench (T-D). Install the Pole Cover (D) to Pole (A).
If no grommet hole exists, drill a 3/8” (10mm) diameter hole through the
mounting surface.
STEP 2
Lay Monitor Arm (F) on flat surface with holes for cable clips facing
down. Add Plastic Spacers (L)
to holes at ends of Monitor Arm (F).
NOTE: Transparent monitor arm image used to show cable clip holes. Holes
are on the underside of arms and are not visable when arm is facing upright.
—————————————————————————————————————————-
Align Monitor Arm and Center Monitor Arm (E,F) so that the holes for the cable clips are facing down. Insert Monitor Arms (F) into Center Monitor Arm (F) as shown below. Secure using M10x47mm Screws (S-A) and 6mm Allen Wrench (T-C).
NOTE: Transparent monitor arm image used to show wire clip holes. Holes
are on the underside of arms and are not visable when arm is facing upright.
—————————————————————————————————————————-
Press Monitor Arm Covers (J) onto the top and bottom of arm joints. Place
Cable Clips (M) into wire
clip holes
STEP 3
Slide arm assembly onto Pole (A) at desired height and secure using
M8x10mm Screws (S-E) and
5mm Allen Wrench (T-B).
STEP 4a – Flat Back Monitors
Attach the Center VESA Plates (P) to the monitors you intend to mount in the center of the mount. Attach Side VESA Plates (O) to remaining monitors. Secure using M4x12mm Screws (M-A)
Center VESA Plate (P) Installation
Side VESA Plate (O) Installation
NOTE: Hand tighten screws to avoid stripping the plastic screw heads.
STEP 4b
Attach the Center VESA Plates (O) to the monitors you intend to mount in
the center of the mount. Attach Side VESA Plates (N) to remaining
monitors. Secure using M4 Spacers (M-C) , M4x30mm Screws (M-B) and a
Phillips screwdriver.
Center VESA Plate (O) Installation
Side VESA Plate (N) Installation
STEP 5
Slide the center monitors onto the Center Head (E1) and Mount (G). Install
M4x6mm Screws (S-G) to secure the monitors.
STEP 6
Slide the outer monitors onto Outer VESA Heads (F1). Secure with Cap Nut
(S-F)
To adjust center monitor swivel or tilt, use 3mm Allen Wrench (T-A) to loosen center set screw on the Center Head (E1) and Mount (G), as shown at left.
Adjust Monitor Tilt
Pry off Plastic Covers (F2) from the Outer VESA Heads (F1). The exposed nut on the side is used to adjust the tilt. Tighten the nut using Wrench (T-D) to adjust. Replace Plastic Covers (F2).
Adjust Monitor Height
To adjust center monitor height, turn the screw behind Center Head (E1)
and Mount (G) using the 5mm Allen Wrench (T-B)
To level the side monitors, remove the Cap Nut (S-F) and turn the inner
bolt with the 3mm Allen Wrench (T-A) to raise or lower the monitor.
Replace Nut after the adjustment.
To adjust swivel joint tension, remove the Monitor Arm Cover (J) and turn
the bolt underneath with
the 6mm Allen Wrench (T-C).
Cable Management
Manage cables using Cable Clips (M) on assembled arms. Remove the split
cap from the Pole (A) and
feed cables through, pulling ends out from the opening in back. Replace the
split cap when finished.
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
www.vivo-us.com
Chat live with an agent!
AVG. RESPONSE TIME (within office hrs): 1HR 8M
-23% within < 15m
– 38% within < 30m
-61% within < 1hr
-83% within <2hr
-92% within < 3hr
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Quad Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>