access LIGHTING 20825LEDD LED Flush Mount Instruction Manual
- June 4, 2024
- access LIGHTING
Table of Contents
access LIGHTING 20825LEDD LED Flush Mount
INSTALLATION INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS MESURES DE SECURITE A RESPECTURE
Before assembling your ACCESS LIGHTING fixture, please make sure that you
carefully read through this instruction sheet. Save this instruction sheet and
refer to it when additions to or changes in the fixture configuration are
made.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE THE CORRECT BRANCH CIRCUIT CONDUCTOR. CONSULTER UN ELECTRICIAN QUALIFIED POUR VOUS ASSURER QUE LES CONDUCTEURS DE LA DERIVATION SONT ADEQUATE THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHERENTS
NOTE: The important safeguards and instructions that appear in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care, are factors that can’t be built into any product. These factors must be supplied by the person(s) caring for and operating the fixture. Read all instructions Do not install this fixture in hazardous locations. N’installez pas cet appareil dans des emplacements dangereux. Do not install any fixture assembly closer than 6 inches from any curtain or similar combustible material. Laisser une distance d’au moins 6 pouces entre ce luminaire et la toute surface combustible.
“WARNING Risk of Fire and Electric Shock.” “CAUTION: Risque d’ Incendie et de Choc Electriques.”
GENERAL INFORMATION
All electrical connections must be in accordance with all ordinances, Local and the U.S. National Electrical Codes (NEC). These fixtures are intended for mounting to a standard 4″ metal octagon outlet box. The box must be directly supported by the building structure and U.L. Recognized.
COLLECTION
- ROMA
APPLICATION
- FLUSH MOUNT
MODEL NO.
- 20825LEDD
- 20826LEDD
WHAT WE PROVIDE
- Mounting Hardware
- 1 x Glass shade
- LED
WHAT YOU NEED
- Screwdriver
- Wire Cutters
- Wiring Supplies as Specified by Electrical Code
Recommended Dimmers
- Lutron DVCL-153P
- Lutron CTCL-153P
- Lutron TGCL-153P
- Lutron MACL-153M
- Lutron PD-6WCL
- Lutron MRF2-6CL
STEP BY STEP INSTRUCTIONS
- Before starting your installation disconnect the Power by turning off the Circuit Breaker or by removing the fuse at the fuse box.
- Just turning the light off at the light switch is not sufficient to prevent electrical shock.
- PREPARE FIXTURE AND MAKE WIRE CONNECTIONS ****If there is an existing fixture remove it. Expose the supply wires from the J-box. Connect the black supply wire to the black fixture wire. Secure with the supplied wire nuts. Connect the white supply wire to the white fixture wire. Secure with the supplied wire nuts. Attach the green J-Box wire around the green hexagonal head screw or connect it to the green supply grounding wire of the fixture. Secure all wires with electrical tape (not supplied). Tuck all wires carefully into the J-Box.
- MOUNT THE FIXTURE Align the fixture canopy to the J-box and secure it with the supplied screws. Align the glass shade to the fixture and secure it by rotating the glass clockwise until secured against the fixture body.
- RESTORE THE ELECTRICITY AND CHECK THE OPERATION OF YOUR NEW ACCESS LIGHTING FIXTURE
CAUTION: If the fixture is to be removed or replaced, please ensure that the electricity is switched off and that the fitting is cool before touching it.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>