access LIGHTING 63143LEDDLP Port Nine 1 Antique Brushed Brass LED Wall Sconce with Clear Glass Instruction Manual
- June 4, 2024
- access LIGHTING
Table of Contents
access LIGHTING 63143LEDDLP Port Nine 1 Antique Brushed Brass LED Wall
Sconce with Clear Glass
IMPORTANT SAFETY INSTRUCTIONS
MESURES DE SECURITE A RESPECTURE
Before assembling your ACCESS LIGHTING fixture, please make sure that you
carefully read through this instruction sheet. Save this instruction sheet and
refer to it when additions to or changes in the fixture configuration are
made.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR. CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES CONDUCTEURS DE LA DERIVATION SONT ADEQUATS THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHERENTS
NOTE: The important safeguards and instructions that appear in this
manual are not meant to cover all possible conditions and situations that may
occur. It must be understood that common sense, caution and care, are factors
that can’t be built into any product. These factors must be supplied by the
person(s) caring for and operating the fixture. Read all instructions Do not
install this fixture in hazardous locations.
Do not install any fixture assembly closer than 6 inches from any curtain or
similar combustible material.
“WARNING Risk of Fire and Electric Shock.”
GENERAL INFORMATION
All electrical connections must be in accordance with all ordinances, Local
and the U.S. National Electrical Codes (NEC). These fixtures are intended for
mounting to a standard 4” metal octagon outlet box. The box must be directly
supported by the building structure and U.L. Recognized.
INSTALLATION INSTRUCTIONS
- COLLECTION PORT NINE
- APPLICATION WALL
- MODEL NO.
- 63143LEDDLP
- 63144LEDDLP
- 63145LEDDLP
WHAT WE PROVIDE
- Mounting Hardware
- Mounting bracket
- 1 x glass shade
- 1 x E26 ST19 LED bulb
WHAT YOU NEED
- Screwdriver
- Wire Cutters
- Wiring Supplies as Specified by Electrical Code
Recommended Dimmers for Supplied LED bulb
- (ELV) LUTRON Diva DVELV-303P
- (TRIAC) LEVITON Trimatron 6684
- (TRIAC) LEVITON illumatech IPI06
- (TRIAC) LUTRON Ariadni/Toggler TGCL-153P
- (TRIAC) LUTRON Diva DVCL-153P
- (TRIAC) LUTRON Skylark CL SCL-153 or SCL-153P
- (TRIAC) LUTRON Skylark S-600 or S-600P
STEP-BY-STEP INSTRUCTIONS
Before starting your installation disconnect the Power by turning off the Circuit Breaker or by removing the fuse at the fuse box. Just turning the light off at the light switch is not sufficient to prevent electrical shock.
PREPARE THE FIXTURE AND MAKE WIRE CONNECTION
If there is an existing fixture remove it. Expose the supply wires from the
J-box.
Install the mounting bracket to the J-Box with the supplied screws. Gently
pull the supply wires through the hole in the mounting bracket. Connect the
black supply wire to the black fixture wire. Secure with the supplied wire
nuts. Connect the white supply wire to the white fixture wire. Secure with the
supplied wire nuts. Attach the green
J-Box wire around green hexagonal head screw or connect it to the green supply
grounding wire of the fixture. Secure all wires with electrical tape (not
supplied). Tuck all wires carefully into the J-Box.
MOUNT THE CANOPY
Place the backplate to the mounting bracket, align the holes and secure with
the supplied screw knobs.
INSTALL THE GLASS SHADE AND THE BULB
Align the glass shade over the socket and secure with the supplied socket
ring. Insert the bulb.
DO NOT EXCEED THE MAXIMUM WATTAGE AS STATED ON THE WARNING LABEL
RESTORE THE ELECTRICITY AND CHECK THE OPERATION OF YOUR NEW ACCESS LIGHTING
FIXTURE
CAUTION Please ensure that the fitting is cool and switched off before
replacing the bulb. DO NOT use bulbs that might exceed the maximum wattage,
stated on caution label.