WANTJOIN B0BZWRL8B1 Hot Dog Grill Machine User Manual

June 15, 2024
Wantjoin

USER MANUAL
Hot Dog Griller Machine

For your safety, please read the manual before using the machine.

WARNING

WARNING
For your safety, please read the instructions before using the machine.

  1. DO NOT touch the hot surface to avoid burns.
  2. DO NOT immerse product and cable into water to avoid electric shock.
  3. MUST beware all age under 18 or area which near children when using the product.
  4. UNPLUG the product and let it to cool down before cleaning or after using.
  5. ONLY find the nearby authorized service agency for inspection, repair and adjustment when the appliance,cable or the cord being damaged.
  6. NEVER use not from the manufactured electrical appliance to avoid injury.
  7. NEVER for outdoor using.
  8. DO NOT hang the wires on table edges or any hot surface.
  9. DO NOT operate or place the product near hot gas or electic stoves.
  10. MUST becareful when moving the machine that contain hot oil to avoid burns.
  11. MUST turn off all control or functions keys before uplug the product.
  12. NEVER use the product for other purposes.
  13. KEEP and SAVE the instruction properly.

CLEANING & MAINTENANCE

Cleaning steps:

  1. Press the power button to “O” and don’t reset the rotary knob. After natural cooling, cover the roller surface with a wet cloth and clean the machine after the adhesive softens.

  2. With a soft cloth well soaked, gently wipe each roller until it is completely clean.
    Wipe direction must be from the end to the middle to remove adhesive from the roller, and avoid machine breakdown caused by adhesive’s falling into bearing.

  3. After the roller is wiped clean,please tum off the power,unplug the plug,take out the chassis,scrub with hot soapy water or deergent, rinse with water chassis, and add the chassis.

  4. Wipe the rest of the machine thoroughly with a damp, hot soft cloth until it is completely clean.

Clean attention:
a. The placement site should have no direct sunlight, no dust, and have good ventilation.
b. We paint unstick coat on the roller surface, so just use the wooden scoop or cloth when cleaning, in case of the unstick coat break away from the roller surface.
c. Please don’t clean the roller with water, it may damage the machine.

INSTALLATION

Kit Details

  1. Flat shims*2
  2. Right-angle spacers*2
  3. Horizontal strip with folded corners*2
  4. Screws*N
  5. Trapezoidal glass on the side*2
  6. Small rectangular glass back panel*2
  7. Large rectangular glass back panel*2

TROUBLESHOOTING

Issue Name Reason Solution
Different heating effects in the  roller Hot dogs may be affected

by the environment. Windy
environment takes away
heat, resulting in uneven
heating.| We recommend using a glass cover (for covered  models) to reduce heat dissipation and preheat  the hot dog for 3-5 minutes before putting it on the roller.
Hot dogs heated unevenly
Actual temperature is different
from the set temperature
The stick stops rolling| Internal chain fracture| If the chain is broken, please contact us for  replacement. If the chain is not stuck on the drum, clamp the chain on the drum. (as picture)

The roller is not stuck in
the chain| Please open the side panel to check the inside (if  the front roller is broken, please open the left  panel. If the rear roller is broken, please open the right panel).
3 roaster smokes| Put the frozen food in
the heated machine.| Brush a layer of oil on it before use, and preheat  the machine to the baking temperature for 3-5 minutes.
| It is recommended that the frozen sausage be left  at room temperature for 10-15 minutes before  putting it on the machine.
3 roaster smokes| It’s normal to use the machine for  the first time and bake sausage at  room temperature, with smoke.| Lower the temperature
Brush some oil on the machine with a brush

INSTALLATION

a. Add a little edible plant oil on both end of the moving roller before using, and this is to make sure that the rollers can move steady.
b. Tum on the power switch.
c. There are two switches on the front-panel of the machine, and they control two-group rollers, the left rotary knob controls the front rollers, and the right rotary knob controls the back rollers. so the user can turn on one switches or two  according to the need and the hotdag quantity firstly, adjust the temperature to a suitable centigrade secondly, the the heating indicator light is on, it will be out when the temperature reaches the setted one.if the temperature become  lower after some time using, the heating indicator light will be on again, then start heating again. It works circularly, this can save energy, on the other hand, it will ensure the hot dog quality cooking.
d. Temperature setting suggestion:
122-212 ℉: Used for heat preservation.
212-392 ℉: Normal heating temperature range.
248-320 ℉: The best heating range, usually takes 10-15 minutes to heat.
450-482 ℉: Heating quickly, it is necessary to check the heating condition frequently to prevent burning.
e. Turn off the power switch after using.

NOTE
Set according to the actual usage temperature.

FUNCTION FEATURES

PARAMETER

Type| voltts
(v)| Power
(Kw)| Temperature
scope| Roller
quantity| Out packing
(mm)
---|---|---|---|---|---
with 5 rollers| 110V/60HZ| 0.7| 32 °F-482 °F| 5| 580X255X170
with 7 rollers| 110V/60HZ| 0.9| 32 °F-482 °F| 7| 580X330X170
with 11 rollers| 110V/60HZ| 1.| 32 °F-482 °F| 11| 580X480X170

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals