VIVO STAND-V032FW Dual Monitor Desk Stand Instruction Manual
- June 15, 2024
- Vivo
Table of Contents
VIVO STAND-V032FW Dual Monitor Desk Stand
Product Information
Specifications:
- SKU: STAND-V032F/FW
- Weight Capacity: 22 lbs (10kg) per arm
Package Contents
- A (x1) Pole
- B (x1) Base
- C (x1) Swivel Arm
- D (x2) VESA Plate
- E (x1) Pole Cap
- F (x4) Cable Clip
- G (x1) Pole Cable Clip
- S-A (x2) Security Nut
- S-B (x3) M6x16mm Screw
- M-A (x8) M4x12mm Thumbscrew
- M-B (x8) M4x30mm Screw
- M-C (x8) M6 Spacer
- T-A (x1) 3mm Allen Wrench
- T-B (x1) 5mm Allen Wrench
Tools Needed:
- Phillips Screwdriver
Assembly Steps
Step 1: Install Pole to Base
- Attach Pole (A) to Base (B) using M6x16mm Screws (S-B).
- Tighten the screws with a 3mm Allen Wrench (T-A).
Step 2: Attach Swivel Arm and Pole Cap
- Slide Pole Cable Clip (G) and Swivel Arm (C) down onto Pole (A).
- Tighten the screw with a 5mm Allen Wrench (T-B).
- Attach Pole Cap (E) to the top of Pole (A).
- Attach Cable Clips (F) to the Arms.
Step 3 : Attach VESA Plates to Monitors
Option A: Flat Back Monitor
-
Attach VESA plates (D) to the monitors using M4x12mm
Thumbscrews (M-A). -
Hand-tighten the screws to avoid stripping the plastic screw
heads.
Option B: Curved Back Monitor
-
Attach VESA plates (D) to the monitors using M6 Spacers (M-C)
and M4x30mm Screws (M-B). -
Tighten the screws with a Phillips screwdriver.
Step 4: Install Monitors onto Swivel Arm
- Slide the monitors onto the heads of Swivel Arm (C).
- Install Security Nuts (S-A) to secure the monitors.
- Make sure Security Nuts (S-A) are installed before rotating the
monitors.
Step 5: Adjust Tilt Angle and Level Monitors
To adjust the tilt angle:
- Tighten the bolt on the side of the tilt joint with the 5mm
Allen Wrench (T-B).
To level the monitors:
- Remove the security nut and turn the bolt with the 3mm Allen Wrench (T-A) to raise or lower the monitor.
- Replace the nut after adjusting.
- Ignore this step if monitors are already level.
Step 6: Adjust Swivel Joints and Manage Cables
- Use the 5mm Allen Wrench (T-B) to adjust the swivel joints if needed.
- Manage cables and store Allen Wrenches (T-A, T-B) in Pole Cable Clip (G) for future use.
Step 7: Caution
To prevent tipping, please be careful not to extend the arms
beyond the arrow range.
Frequently Asked Questions (FAQ)
- Q: What is the weight capacity of this dual monitor desk stand?
- A: The weight capacity is 22 lbs (10kg) per arm.
- Q: Can I use this desk stand for curved back monitors?
- A: Yes, you can use this desk stand for both flat-back and curved-back monitors. Please follow the instructions in Step 3 for attaching VESA plates.
- Q: How do I adjust the tilt angle of the monitors?
- A: To adjust the tilt angle, tighten the bolt on the side of the tilt joint with the provided 5mm Allen Wrench (T-B).
- Q: How do I level the monitors?
- A: To level the monitors, remove the security nut and turn the bolt with the provided 3mm Allen Wrench (T-A) to raise or lower the monitor. Replace the nut after adjusting.
- Q: Can I adjust the swivel joints of the desk stand?
- A: Yes, you can adjust the swivel joints using the provided 5mm Allen Wrench (T-B).
- Q: What should I do if I have any issues or need assistance?
- A: If you have any issues or need assistance, you can contact our dedicated support team via phone at 309-278-5303 or email at help@vivo-us.com. You can also visit our website at www.vivo-us.com
to chat live with an agent.
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.
TIP OVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD OR BACKWARD.
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
THE USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
TOOLS NEEDED
TOOLS NEEDED
ASSEMBLY STEPS
- STEP 1 Install Pole (A) to Base (B) using M6x16mm Screws (S-B). Tighten with 3mm Allen Wrench (T-A).
- STEP 2 Slide Pole Cable Clip (G) and Swivel Arm (C) down onto Pole (A) and tighten the screw with 5mm Allen Wrench (T-B). Attach Pole Cap (E) to the top of Pole (A). Attach Cable Clips (F) to the Arms
- STEP 3 OPTION A: Flat Back Monitor
Attach VESA plates (D) to the monitors using M4x12mm Thumbscrews (M-A).
NOTE: Hand-tighten screws to avoid stripping the plastic screw heads
-
OPTION B: Curved Back Monitor
Attach VESA plates (D) to the monitors using M6 Spacers (M-C) and M4x30mm Screws (M-B). Tighten with a Phillips screwdriver. -
STEP 4 OPTION B: Curved Back Monitor
Attach VESA plates (D) to the monitors using M6 Spacers (M-C) and M4x30mm Screws (M-B). Tighten with a Phillips screwdriver. Slide the monitors onto the heads of Swivel Arm (C) and install Security Nuts (S-A). Make sure Security Nuts (S-A) are installed before you rotate the monitors.
- STEP 5 Tighten the bolt on the side of the tilt joint with the 5mm Allen Wrench (T-B) to fix the tilt angle.
To level the monitors, remove the security nut and turn the bolt with the 3mm Allen Wrench (T-A) to raise or lower the monitor. Replace nut after the adjustment.
- STEP 6 Use 5mm Allen Wrench (T-B) to adjust swivel joints if needed. Manage cables and store Allen Wrenches (T-A, T-B) in Pole Cable Clip (G) for future use.
- STEP 6 Use 5mm Allen Wrench (T-B) to adjust swivel joints if needed. Manage cables and store Allen Wrenches (T-A, T-B) in Pole Cable Clip (G) for future use.
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
contact
Open Monday – Friday 7:00 am – 7:00 pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
- 309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
- www.vivo-us.com AVG. RESOLUTION TIME (within office hrs): < 15 M
- help@vivo-us.com AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
- FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo- us.com/products/stand-v032
GET IN TOUCH | Monday-Friday from 7:00 am-7:00 pm CST
- help@vivo-us.com
- www.vivo-us.com Chat live with an agent!
- 309-278-5303
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Dual Monitor Desk Stand up to 32" Screens – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>