GUANGDONG YR5302 Hand Held Remote Control Instruction Manual

GUANGDONG YR5302 Hand Held Remote Control

Product Introduction

• Specifications
  • Motor model: YR5302
  • Emission frequency: 2402-2480MHz
  • Transmit power: BLE 5.0
  • Communication protocol: 4
  • Use battery: AAA BATTERY X 2pcs
  • Transmission channel: Two-channel modes
• Product Size
  • The length (L) of the remote control is dependent on product specifications and measures approximately 132mm x 36.9mm x 14.6mm.
• Button Functions
  • [Up/Open]: Open the curtain.
  • [Down/Close]: Close the curtain.
  • [Intermediate Stop 75%]: Short press to tilt up.
  • [Intermediate stop 50%]: Short press to stop. Long press for 1.5 seconds to run to the IP1 limit position. Long press for 4 seconds to run to the default 50% limit (default is 75%).
  • [Stop/50%]: Long press to clear the limit position.
  • [Channel selection]: Used to select channels.
  • [Channel setting]: Used for channel settings and limit point configuration.
• Channel Setting
  • The remote control supports two channels and four-channel modes.
  • The current maximum number of channels in use is set to two or four-channel switches.
• Two Channel Mode
  • To switch between channel 1 and channel 2:
  • Press the [Channel Selection] button when the LED of the remote control is off.
  • The indicator light of the current channel will light up.
  • Press the [Channel Selection] button again within 3 seconds to select the next channel.
  • The channels can be selected in the sequence of channel 1 and channel 2.
• Four-Channel Mode
  • To switch between channel 1, channel 2, channel 3, and channel 4:
  • Press the [Channel Selection] button when the LED of the remote control is off.
  • The indicator light of the current channel will light up.
  • Press the [Channel Selection] button again within 3 seconds to select the next channel.
  • The channels can be selected in the sequence of channel 1, channel 2, channel 3, and channel 4.
• FAQ
  • Q: How do I open the curtain?
  • A: Press the [Up/Open] button to open the curtain.
  • Q: How do I close the curtain?
  • A: Press the [Down/Close] button to close the curtain.
  • Q: How do I stop the curtain at 75% tilt?
  • A: Press the [Intermediate Stop 75%] button to stop the curtain at a 75% tilt.
  • Q: How do I stop the curtain at 50% tilt?
  • A: Press the [Intermediate stop 50%] button to stop the curtain. Long press for 1.5 seconds to run to the IP1 limit position. Long press for 4 seconds to run to the default 50% limit (default is 75%).
  • Q: How do I clear the limit position?
  • A: Long press the [Stop/50%] button to clear the limit position.
  • Q: How do I select channels in two-channel mode?
  • A: Press the [Channel Selection] button when the LED of the remote control is off. The indicator light of the current channel will light up. Press the [Channel Selection] button again within 3 seconds to select the next channel.
  • Q: How do I select channels in four-channel mode?
  • A: Press the [Channel Selection] button when the LED of the remote control is off. The indicator light of the current channel will light up. Press the [Channel Selection] button again within 3 seconds to select the next channel.

Product Information

1. Product size
   • Note: The length L of the remote control depend on product specifications (unit: mm)
2. Button function
3. Up/Open
4. Intermediate stop 75%
5. Down/Close
6. Intermediate stop 25%
7. Stop/50%
8. Channel selection
9. Channel setting
10. Product Specifications****
    Motor model| YR5302| Emission frequency| 2402-2480MHz
    ---|---|---|---
    Transmit power| 6±1dBm| Communication protocol| BLE 5.0
    Use battery| AAA BATTERY X 2pcs| Transmission channel| 4

LED indicator function

Two channels modes

• LED 1 is channel 1, and flashing LED indicates the signal is transmitting.
• LED 4 is channel 2, and flashing LED indicates the signal is transmitting.

Four channels modes

• LED 1 is channel 1, and flashing LED indicates the signal is transmitting.
• LED 2 is channel 2, and flashing LED indicates the signal is transmitting.
• LED 3 is channel 3, and flashing LED indicates the signal is transmitting.
• LED 4 is channel 4, and flashing LED indicates the signal is transmitting.

Channel setting

The way to switch two channels and four-channel modes

• The current maximum number of channels in use is set to a two or four-channel switches.

Two-channel mode

• Press the [Channel Selection] when the remote control LED is off, and the indicator light of the current channel will light up. Press the [Channel Selection] again within 3 seconds, and select the channel in the sequence of channel 1→ Channel 2→ group control channel → Channel 1.

Four-channel mode

• Press the [Channel Selection] when the LED of the remote control is off, and the indicator light of the current channel will light up. Press the [Channel Selection] again within 3 seconds, and select the channel in the sequence of channel 1→ Channel 2→ Channel 3 Channel 4→ group control channel → Channel 1.

Button function

Single button function

• [Up/Open]: Open the curtain.
• [Down/Close]: Close the curtain.
• Intermediate Stop 75%: Short press to up tilting; long press 1.5s to run to the IP1 limit position, the default is 75%.
• [Intermediate stop 50%]: Short press,stop.If long press 4 seconds,run to default 50% limit.
• [Intermediate Stop 25%]: short press, turn the leaf down; Hold for 1.5 seconds to run to the IP3 limit, 25% by default.
• [Channel Setting]: used for code learning. The controller or motor will receive and process the unpaired channel setting button only after entering the code learning state.

Combination button function

• [Channel Selection]+[Stop/50%]: reversing, only after the controller or motor enters the code learning state and receives the matched reversing function code will it be processed.
• [Stop/50%]+[Up/Open]: Long press for 5 seconds to start, and then press the [channel setting] button to confirm.
• [Stop/50%]+[Down/Close]: Long press for 5 seconds to enter the ready to disable manual start, then short press [Channel settings] button to confirm.
• [Channel Setting]+[Up/Open]: Press long for 5 seconds at the same time to make the motor enter the state of setting on limit point.
• [ChannelSetting]+[Down/Close]: Press for 5 seconds at the same time to make the motor enter the limit point state of down setting.
• [Up/Open]+[Down/Close]: external control mode switching. The controller or motor will only process after receiving the paired mode switching function code after entering the code learning state.
• [Channel setting]+[75%]: Short press at the same time, set IP1 limit position.
• [Channel setting]+[25%]: Short press at the same time, set IP2 limit position.
• [Channel setting]+[Stop/50%]: Long press at the same time, clear limit position.

FCC Caution

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction. Hand- held remote control instruction manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>