urmet 1099-211B Tele Smart Camera User Guide

: June 15, 2024
: urmet

Table of Contents

Warnings
Simplified EU declaration of conformity
Installation
How to configure the camera in a Wi-Fi network
Documents / Resources

Quick guide
1099/211B
Cloud Camera Series
TELECAMERA SMART WiFi IP 3M PT 3.6MM
WiFi 3M IP SMART CAMERA PT 3.6MM

Warnings

Precautions
Make sure that the device is intact after removing it from the package.
Disconnect the device from the mains before cleaning or maintenance. Do not use spray products to clean the device.
Check that the working temperature is within the indicated range and that the environment is not particularly humid.
Disconnect power by means of the circuit breaker in the event of a failure and/or bad operation.
The device can only be opened by qualified technical personnel.
Exclusively contact an authorised service centre for repairs.

Installation specifications
Arrange a suitable circuit breaker and fuse upstream of the devices.
Make sure that the rating plate data correspond to the power specifications before connecting the device to the mains.

Installation precautions
There are particular environments (such as seashores, harbours, wharves, etc.) that can accelerate corrosion of external parts. Also installation in very dusty environments (quarries, mines, dusty materials, etc.) can compromise the optimal operation.
To prevent device overheating, place it in a well aired position.
For the same reason, the device must not be installed near heat sources as radiators or warm air ducts, in places where it is directly exposed to sun irradiation or in rooms with excessive dust accumulation, subject to mechanical vibrations or impacts.
Consider the device operating temperature range before choosing the place for installation. Do not install the unit over another heating device.
Do not power the device on immediately after moving it from a cold place to a warm one and vice versa. As a general rule, wait for three hours: the device needs this time to adapt to a new environment (temperature, humidity, etc.).

Video recording
This device is not designed as a burglar system but mainly to transmit and record video images. URMET S.p.A. is not in any way responsible for loss or damages of the user consequent to theft.
Before using the device, record a demo video to verify the correct functionality of this feature. URMET S.p.A. is not in any way responsible for loss of recorded data consequent to wrong setting or usage, device misfunctioning or failure.
This device is composed by electronic precision components. Do not hit the device while recording as it might affect the video.

Privacy and Copyright
The IP camera is designed for surveillance systems. Video recording is subject to the laws applicable to the Country where used. It is forbidden to record images with Copyright.
The User is responsible to check and respect all local laws and norms for video signal recording. The manufacturer is NOT in any way liable for any usage of the product which might result not compliant to the relevant norms.

Firmware upgrade
Periodically check the Urmet website in the product-specific section for software and/or firmware updates (go to www.urmet.com in the Products section “CCTV-VIDEOSURVEILLANCE”, type the reference product code in the search field and move to DOCUMENTATION AND RESOURCES).

Network connections
It is possible to connect the camera to a WiFi network via a mobile phone through the app. V-stream.
The device can support a limited number of “unicast” connections so it is possible to show the video on maximum 3 remote devices at the same time depending on the available network band.

Reset button
Press for at least 3 seconds: the camera is completely reset and goes back to default settings.

Simplified EU declaration of conformity

Hereby, URMET S.p.A. declares that the radio equipment type: camera 1099/211B is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.urmet.com

Installation

It is advisable to proceed as follows for correct camera installation and configuration:

Make sure that no units are powered before starting the installation procedure. It is advisable to install and configure one camera at a time if you are installing multiple cameras on the same network.
Connect the camera to the network. It is advisable to check that the Wi-Fi signal received by the camera is higher than or equal to 60.
Position the camera in a point on the wall or other surface and adjust the bracket to frame the required scene.
If you want the camera to record and store video files on a microSD card (not included), plug the card into the slot when the camera is powered off. Power on the camera and use the app to format the card before starting the recording function.

urmet 1099 211B Tele Smart Camera - Parts

IMPORTANT: the camera automatically sets the date and time by default by retrieving this information from the Internet each time it is powered on. If the camera is restarted, the correct date and time cannot be guaranteed if the camera does not access the Internet. If the date and time are not set correctly, the SD memory recordings may be compromised.

How to configure the camera in a Wi-Fi network

The first time the camera is switched on, it is placed in Access Point (AP) mode, and to connect it to a Wi-Fi network, it is necessary to download the URMET V-Stream App to your mobile phone and refer to the quick setup guide.
Quick guide and complete user manual of the products are also available for DOWNLOAD from the URMET website under the section DOCUMENTATION AND RESOURCES at the following links:

urmet 1099 211B Tele Smart Camera - qr code http://qrcode.urmet.com/default.aspx?prodUrmet=166637&lingua=en

Radio frequency band: 2380MHz~2673.5MHz

Maximum radio power transmitted:
Max EIRP 17.41 dBm @ 802.11b
Max EIRP 17.14 dBm @ 802.11g
Max EIRP 15.82 dBm @ 802.11n (HT20)
Max EIRP 15.92 dBm @ 802.11n (HT40)

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 on waste electrical and electronic equipment (WEEE).
The crossed-out wheeled bin symbol on the product or on its packaging indicates that the product must not be disposed of together with ordinary household waste.
The user must therefore dispose of the waste equipment by taking it to a designated collection centre for the recycling of waste electrical and electronic equipment. As an alternative to independent disposal, you can hand in the equipment you wish to dispose of to the retailer when purchasing a new appliance of the same type.
Electronic products up to 25 cm in size can also be handed in for free disposal, with no purchase obligation, at electronics stores with sales areas of over 400 m2.
Adequate separate collection for recycling, treatment and environmentally friendly disposal of the scrapped equipment helps to prevent negative impacts on the environment and on human health, and promotes recycling and/or reuse of the materials with which the equipment is made.

Customer Care
Italia: 011 23 39 810
Export Dept.: +39 011 24 00 250/256
MADE IN CHINA URMET S.p.A.
Via Bologna, 188/C | 10154 Torino (ITALY)
www.urmet.com | info@urmet.com
IF YOU LOVE YOUR BUILDING