ID-NCFG1xx Nature Connect Mini Island

Product Information

Specifications

• Product Name: NatureConnect mini island 4X4
• Model Number: ID-NCFG1xx
• Installation Sheet: NC mini island 4×4 Install sheet

System Overview

The NatureConnect mini island Luminaire is a suspended fixture
that provides lighting. It consists of various components,
including a mounting kit, driver box, and sun sides.

It is important to read all instructions before beginning the
installation process. The fixture should be installed in accordance
with local and national building and electric codes.

Tools Required

– Mounting Kit

– Driver Box

– Sun Sides

Important Safety Instructions

– Install in accordance with local and national building and
electric codes.

– Disconnect or turn off power before attempting any
installation, service, or maintenance.

– Fixture must be connected to building ground via the provided
ground wire terminal before re-connecting to mains power
supply.

Mounting and Power Location

– Ensure the mounting brackets are secured to the structure and
prepositioned accurately while keeping power location in mind.

– Handle the fixture with care and inspect for damage before
installing.

– Do not put any pressure on the lens during installation.

Installation Notes

– Arrange the box fixture on the floor in specified mounting
locations.

– Remove the fixture from the box.

– Install all ceiling mounting components and vertical aircraft
cables using separate installation instructions for Aircraft Cable
Mounting (supplied).

Mounting Orientation

– Before removing the luminaire from the bottom half of the box,
insert the gripper (X4).

– Slide the gripper underneath the bracket and lift it up while
installing the nut with a 17mm wrench.

– Note: A/C cables must run perpendicular to the fixture and not
be angled more than 15 degrees from vertical.

Mounting Installation

– Attach A3 mounting brackets to the structure using hardware
supplied by others.

– Finish assembling the A3 mounts using the supplied
hardware.

– Insert A/C suspension cables and raise the fixture to
position.

– Ensure the fixture is level.

– Note: Requires two or more people for mounting. Leave
protective film on until after installation.

Power Cord Installation

– Follow the power cord installation instructions provided
separately.

FAQ

Q: What should I do before installing the fixture?

A: Read all instructions carefully and inspect the fixture for
any damage.

Q: How should I handle the fixture during installation?

A: Handle the fixture with care and avoid putting pressure on
the lens.

Q: Can I install the fixture in a residential area?

A: The fixture is designed for commercial environments.
Installing it in a residential area may cause harmful interference
to radio communications.

Q: How should I connect the fixture to the power supply?

A: The fixture must be connected to the building ground via the
provided ground wire terminal before re-connecting to mains power
supply.

NatureConnect
NatureConnect mini island 4X4
ID-NCFG1xx NC mini island 4×4 Install sheet
System Overview
These instructions review how to install the NatureConnect mini island Luminaire. The graphics below shows the components required to install the Nature Connect suspended fixture. IMPORTANT: Read all instructions before beginning installation.
i Mounting Kit
· Canopy · #6 Screw · A1 Mounting Bracket · Canopy Extension Ring · A3 Mounting Bracket Assy (X4) · #6 Bolt (X4) · Wire Gripper (X4) · ¼-18 Nut (X4) · 12′ A/C Cable (X4) · Cable strain relief (X2) · ½” Bushing (X2) · 16′ Power Cord
Driver Box
Sun Sides

Tools Required:
· #2 Philips Screwdriver · Heyco PN0019(R12) crimping tool · Medium Flat Head Screwdriver · 17mm Wrench (11/16″)

!

ATTENTION: Install in accordance with local and national building and electric codes.

12/5/2023 page 1 www.ledalite.com

ID-NCFG1xx NatureConnect Installation Instructions

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interreference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.

IMPORTANT: Disconnect or turn off
power before attempting any installation, service or maintenance.

Fixture must be connected to building
ground via the provided ground wire terminal before re-connecting to mains power supply.

!

Mounting and Power Location

Ensure the mounting brackets are secured to the structure and prepositioned accurately while keeping power location in mind. See steps 3 and 4.

! Mounting

! Handle with care

! Inspection
Inspect for damage before installing the luminaire.

No mechanical load on T-Bar. Load on supplied A/C cables only.

Do not put any pressure on the lens during installation.

i Installation Notes
Arrange box fixture on floor in specified mounting locations. Remove fixture from box. Install all ceiling mounting components and vertical aircraft cables using separate installation instruction for Aircraft Cable Mounting (supplied).

!

ATTENTION: Install in accordance with local and national building and electric codes.

12/5/2023 page 2

ID-NCFG1xx NatureConnect Installation Instructions

!
1 Cable Gripper Installation
Nut Gripper

2 Mounting Orientation
Driver Box
Sun Sides

3 Mounting Layout

Sun Sides

Before removing the luminaire from the bottom half of Box, insert gripper (X4). Slide gripper (supplied) underneath bracket and lift-up the gripper while installing nut with 17mm Wrench. (11/16″).
Note: A/C cables must run perpendicular to fixture and not be angled more than 15 degrees from vertical.

Determine orientation of the skylight in the ceiling according to the lighting plan

Driver Box
Layout mounting points to building structure. Distance between mounting points is 26 ¼” (666mm) X 21 3/8″ (544mm) Note: A/C cables must run perpendicular to fixture and not be angled more than 15 degrees from vertical.

!

ATTENTION: Install in accordance with local and national building and electric codes.

12/5/2023 page 3

ID-NCFG1xx NatureConnect Installation Instructions

4 Mounting Installation
A3 Mounting Brackets

5 Power Cord Installation

5.1 Power Cord Installation

½” Bushing

• Cable strain relief

Attach A3 mounting brackets to structure. (Hardware supplied by others) Finish assembling the A3 mounts using supplied hardware. Insert A/C suspension cables and raise fixture to Position. Ensure fixture is level. Note: Requires two or more people for mounting. Leave protective film on until after installation
6 Link ­ Install Guide
SCAN

Detach Driver box by removing 4 screws using #2 Philips screwdriver. Determine power drop location and remove knockout(s) using a flat head screwdriver.
6.1 Link – App

Install ½” bushing from below. Feed the power cord from above into fixture driver box. Attach cable strain relief using HeycoPN0019(R12) crimping tool. Make connections using wire nuts(supplied by others) and re-attach driver box cover. Remove protective film on lens
Note: Alternate connection with flexible

• conduit at . (Supplied by others).

6.2

Link ­ Commissioning Guide

SCAN

OR
Click for LINK

OR
CLICK FOR LINK

Download the Link install Guide

Download the Interact App

Download the Link Commissioning guide

!

ATTENTION: Install in accordance with local and national building and electric codes.

12/5/2023 page 4

www.signify.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>