Studio 374A Intercom Beltpack User Guide

: June 15, 2024
: Studio

Studio 374A Intercom Beltpack

Studio-374A-Intercom-Beltpack-product

Product Information

Specifications

Serial Numbers: M374A-04001 to 04500
Application Firmware: 2.1 and later
Power Requirement: Power-over-Ethernet (PoE)
Operating Parameters: Configurable using the STcontroller software application
Audio Channels: 4
Enclosure: Aluminum alloy
Belt Clip: Stainless steel

Introduction
The Model 374A Intercom Beltpack is designed for use in party-line (PL) intercom applications over a standard IP network. It can be used with an external Dante-enabled audio matrix, such as the Studio Technologies’ Model 5421 or Model 5422A Dante Intercom Audio Engine units, for party-line communication. Alternatively, it can be used for point-to-point communication or interfaced with Dante-compatible matrix intercom systems.

The belt pack requires only a single Power-over-Ethernet (PoE) connection for operation. The STcontroller software application allows easy configuration of key user features, including electret microphone powering, microphone preamplifier gain, talk button operation, call receive an indication, remote control inputs, and headphone channel assignment. User features include integrated sidetone, remote mic kill (talk off), call receive and send, and audio monitor-only modes. The digital audio signal path ensures excellent audio quality.

The Model 374A features four talk pushbutton switches and four push-in/push- out (pop-out) rotary controls for headphone output level adjustment. The enclosure is made from an aluminum alloy, providing both lightweight and ruggedness. It also includes a stainless steel belt clip for easy attachment to clothing. With its high audio quality, low distortion, low noise, and high headroom, the Model 374A is suitable for various applications, including sports and entertainment TV and radio events, streaming broadcasts, corporate and government AV installations, and post-production facilities.

Dante Audio-over-Ethernet
The Model 374A supports Dante Audio-over-Ethernet. Two bi-color LEDs indicate the Dante connection status. The Dante Controller’s Identify command can be used to activate the talk button LEDs in a unique highly visible sequence and turn off any active talk channels.

Product Usage

Connecting the Beltpack
To connect the Model 374A Intercom Beltpack:

Ensure you have a PoE-enabled network switch or PoE injector.
Connect an Ethernet cable from the network switch or injector to the belt pack’s Ethernet port.
Attach the belt pack to your clothing using the stainless steel belt clip.

Configuring Operating Parameters
Use the STcontroller software application to configure the operating parameters of the belt pack:

Download and install the STcontroller software from the Studio Technologies website.
Launch the STcontroller software on your computer.
Connect the belt pack to your computer using a USB cable.
In the STcontroller software, select the connected belt pack from the device list.
Adjust the configurable parameters according to your preferences, such as microphone power, preamplifier gain, talk button operation, call receive indication, remote control inputs, and headphone channel assignment.
Click “Apply” to save the changes to the belt pack.

Using the Beltpack
The Model 374A Intercom Beltpack offers various features for communication:

Talk Button: Press the talk button to activate your microphone and transmit your voice to other connected units.
Sidetone: The belt pack provides integrated sidetone, allowing you to hear your voice in the headphones when talking.
Remote Mic Kill (Talk Off): Use the remote control inputs to remotely disable the microphone transmission.
Call Receive and Send: The belt pack supports call receive and send functions for communication with other units.
Audio Monitor-Only Mode: Activate the audio monitor-only mode to listen to the audio feed without transmitting.

FAQ

Q: What is the power requirement for the Model 374A Intercom Beltpack?
A: The belt pack requires Power-over-Ethernet (PoE) for operation.
Q: How many audio channels does the belt pack support?
A: The Model 374A supports four audio channels.
Q: Can I configure the belt pack’s operating parameters?
A: Yes, you can use the STcontroller software application to configure parameters such as microphone power, preamplifier gain, talk button operation, call receive an indication, remote control inputs, and headphone channel assignment.
Q: What applications is the Model 374A suitable for?
A: The belt pack is suitable for various applications, including sports and entertainment TV and radio events, streaming broadcasts, corporate and government AV installations, and post-production facilities.

This User Guide is applicable for serial numbers M374A-04001 to 04500 with application ﬁrmware 2.1 and later.

Revision History

Issue 5, March 2021:
Documents addition of remote control inputs.
Issue 4, February 2021:
Documents expansion of Call Indication function.
Issue 3, August 2019:
Documents revision to STcontroller (version 2.02.00 and later) which separates microphone power and microphone gain conﬁguration.
Issue 2, April 2019:
Documents new receive and send call function.
Issue 1, June 2018:
Initial release.

Introduction

The Model 374A Intercom Beltpack begins with the features offered by traditional party-line intercom user devices and adds a range of new capabilities along with the advanced performance and ﬂex-ability that Dante® audio-over-Ethernet provides. With four independent talk and listen channels the Model 374A bridges the gap between typical single- and dual-channel party- line devices and permanent-ly installed multi-channel intercom panels. Imagine the possibilities—four channels of high-quality party-line intercom in a compact, user-worn package.

Over a standard IP network, multiple Model 374A units can be used in party- line (PL) intercom applications with help from an external Dante-enabled audio matrix such as the Studio Technologies’ Model 5421 or Model 5422A Dante Intercom Audio Engine units. Or, units can be used “point-to-point” or interfaced with Dante-compatible matrix intercom systems. Only a single Power- over-Ethernet (PoE) connection is required for operation. Key user features can be easily conﬁgured using the STcontroller software application. Conﬁgurable parameters include electret microphone powering, microphone pre- ampliﬁer gain, talk button operation, call receive indication, remote control inputs, and headphone channel assignment. User features include integrated sidetone, remote mic kill (“talk off”), call receive and send, and audio monitor-only modes. The wide range of capabilities, along with the excellent audio quality provided by the digital audio signal path, offers a unique and powerful user experience.

The setup and conﬁguration of the Model 374A is simple. An etherCON® RJ45 receptacle is used to interconnect with a standard twisted-pair Ethernet port associated with a local-area network (LAN). This connection provides both power and bidirectional digital audio. A broadcast or intercom-style stereo or monaural headset with a dynamic or electret (DC-powered) microphone interfaces with the unit using a 5-pin XLR connector. A 3-conductor 3.5 mm jack al-lows the connection of two external switches or contact closures to activate two selected talk channels.

The STcontroller software application is used to select the unit’s operating parameters. Four talk pushbutton switches can be conﬁgured for optimal operation. Four push-in/push-out (“pop out”) rotary controls make it easy to set and maintain the desired headphone output level. The Model 374A’s enclosure is made from an aluminum alloy which offers both light weight and ruggedness. A stainless steel “belt clip,” located on the back of the unit, allows direct attachment to a user’s clothing.

The audio quality of the Model 374A’s four audio channels is excellent, with low distortion, low noise, and high headroom. Careful circuit design and rugged components ensure long, reliable operation. A wide range of applications can be supported, including sports and entertainment TV and radio events, streaming broadcasts, corporate and government AV installations, and post-production facilities.

$Studio-374A-Intercom-Beltpack-fig- $1$$

Dante Audio-over-Ethernet
Audio data is sent to and received from the Model 374A using the Dante audio- over-Ethernet media networking technology. As a Dante-compliant device, the Model 374A’s four audio output (Dante transmitter) and four audio input (Dante receiver) channels can be interconnected (routed) with other devices using the Dante Controller software application. The Dante transmitter and receiver channels are limited to supporting four Dante ﬂows, two in each direction. The digital audio’s bit depth is up to 24 with a sampling rate of 48 kHz. The Model 374A is AES67 compatible and compliant with the Dante Domain Manager™ software application.

Two bi-color LEDs indicate the Dante connection status. The Dante Controller’s Identify command takes on a unique role with the Model 374A. Not only will it cause the talk button LEDs to light in a unique highly visible sequence, but it can also be conﬁgured to turn off any active talk channels.

Audio Quality
The Model 374A’s completely “pro” performance is counter to the less-than- stellar reputation of typical party-line (PL) intercom audio. A low-noise, wide dynamic-range microphone preampliﬁer, and associated voltage-controlled- am-pliﬁer (VCA) dynamics controller (compressor) ensures that microphone audio quality is preserved while minimizing the chance of signal overload. DC power to support electret microphones can be enabled if necessary. The output of the microphone preamp and compressor is routed to an analog-to-digital converter (ADC) section that supports a sampling rate of 48 kHz with a bit depth of up to 24. The audio signal, now in the digital domain, travels through the processor and onto the Dante interface section where it is packetized and prepared for transport over Ethernet.

Audio input signals arrive via four Dante receiver channels. The supported sampling rate is 48 kHz with a bit depth of up to 24. The audio signals pass into the Model 374A’s processor where channel routing, headphone level control, and sidetone creation are performed within the digital domain. This provides ﬂexibility, allowing for precise control of the audio signals and eliminates the need for the four rotary level controls from having to directly handle analog audio signals. The audio signals destined for the 2-channel headphone output are sent to a high-performance digital-to-analog converter and then on to robust driver circuitry. High signal levels can be provided to a variety of headsets, headphones, and earpieces.

Call Function
A call function allows Model 374A users to receive and send channel-speciﬁc visual alert signals. Using 20 kHz tones, the call signals are sent within the audio channels (“in band”) allowing interoperability between multiple Model 374A units as well as being compatible with legacy party-line intercom systems. Call signals can be useful to indicate to users that they are needed “on headset” or should be actively listening to an intercom channel. The call function can also be used to provide real-time cues to production personnel during the running of live events. Call signals present on the four audio input (Dante receiver) channels can be detected and displayed. To optimize for speciﬁc applications, a conﬁgura-tion choice allows how the Model 374A will display Call when 20 kHz has been detected. Pushbutton 4, on the Model 374A’s top panel, can be conﬁgured to serve as a call button. This allows a call signal to be generated for talk channels 1, 2, and 3.

Configuration Flexibility

A highlight of the Model 374A is its ability to be easily conﬁgured to meet the needs of speciﬁc users and applications. All conﬁguration choices are made using the STcontroller software application that communicates with the Model 374A by way of an Ethernet network connection. Con-ﬁgurable parameters include microphone power and preampliﬁer gain, sidetone audio operation, talk button operation, call indication, remote control inputs, and headphone monitoring.
The microphone input can be selected for compatibility with dynamic or electret (DC-powered) microphones. The gain of the microphone preampliﬁer can be selected from among four choices. These allow compatibility with a variety of microphones that are part of broadcast and intercom headsets.

A unique Model 374A feature is the ability to individually conﬁgure how the four talk pushbutton switches function; four choices are available. For standard intercom belt pack operation either Push to Talk or Push to Talk/Tap to Latch operation can be selected. For situations where only monitoring of an intercom channel is desired a Talk Disabled mode is available. For advanced monitoring-only situations, the Talk Disabled/Phones Tap to Latch mode can be selected such that a button will serve in an audio on/off role.

Conﬁguration choices allow the two remote control inputs to be individually assigned to activate any one of the four talk channel functions. Four audio channels arrive via Dante and are destined for the 2-channel headphone output. Each input source can be independently routed to the left headphone channel, right headphone channel, or both the left and right headphone channels. This ﬂexibility allows a variety of listening environments to be created, including stereo, single-channel monaural, and dual-channel monaural.

Ethernet Data and PoE
The Model 374A connects to an Ethernet data network using a standard 100 Mb/s twisted-pair Ethernet interface. The physical interconnection is made by way of a Neutrik® etherCON RJ45 receptacle. While compatible with standard RJ45 plugs, etherCON allows a ruggedized and locking interconnection for harsh or high-reliability environments. An LED displays the status of the network connection.

The Model 374A’s operating power is provided by way of the Ethernet interface using the 802.3af Power-over-Ethernet (PoE) standard. This allows fast and efﬁcient interconnection with the associated data network. To support PoE power management, the Model 374A’s PoE interface reports to the power sourcing equipment (PSE) that it’s a class 1 (very low power) device.

Future Capabilities and Firmware Updating
The Model 374A was designed such that its capabilities and performance can be enhanced in the future. A USB connector, located on the unit’s main circuit board (underneath the unit’s cover), allows the application ﬁrmware (embedded software) to be updated using a USB ﬂash drive. The Model 374A uses Audinate’s Ultimo™ integrated circuit to implement the Dante interface. The ﬁrmware in this integrated circuit can be updated via the Ethernet connection, helping to ensure that its capabilities remain up to date.

Getting Started

What’s Included
Included in the shipping carton are a Model 374A Intercom Beltpack and instructions on how to obtain an electronic copy of this guide. As a device that is Power-over-thernet (PoE) powered, no external power source is provided. In most applications, an Ethernet switch with the required PoE capability will be utilized.

Connections

In this section signal interconnections will be made using the three connectors located on the bottom of the Model 374A’s enclosure. An Ethernet data connection with Power-over-Ethernet (PoE) capability will be made using either a standard RJ45 patch cable or an etherCON-protected RJ45 plug. A dual- channel or single-channel (dual- or single-ear) headset will be connected using a cable-mounted 5-pin male XLR connector. Some applications will use the 3-conductor 3.5 mm jack that provides access to the Model 374A’s two remote control inputs.

Ethernet Connection with PoE
A 100BASE-TX Ethernet connection that supports Power-over-Ethernet (PoE) is required for Model 374A operation. This one connection will provide both the Ether-net data interface and power for the Model 374A’s circuitry. A 10BASE-T connection is not sufﬁcient and a 1000BASE-T (GigE) connection is not supported unless it can automatically “fall back” to 100BASE-TX operation. The Model 374A supports Ethernet switch power management, enumerating itself as a PoE class 1 device. Any source that is compliant with the IEEE® 802.3af standard will function correctly. Should the selected Ethernet switch port support Energy-Efﬁcient Ethernet (EEE) it must be disabled to help ensure reliable Dante operation.

The Ethernet connection is made by way of a Neutrik etherCON-protected RJ45 receptacle that is located on the bottom of the Model 374A’s enclosure. This allows connection by way of a cable-mounted etherCON connector or a standard RJ45 plug. The Model 374A’s Ethernet interface supports auto MDI/MDI-X so a cross-over cable will never be required.

Headset Connection
The Model 374A provides a 5-pin female XLR connector that interfaces with the microphone and headphone connections of an intercom or broadcast-style headset. Refer to Figure 2 for connection details. The microphone input connections are compatible with most unbalanced dynamic or electret (low- voltage DC-powered) microphones. A balanced dynamic microphone should, in most cases, also function correctly if the signal – (low) is connected to Model 374A’s mic in –/shield connection. No support is provided for microphones that require P12 or P48 phantom power.

To allow users of stereo (dual-earpiece or “double muff”) headsets to hear a monaural version of the two headphone output channels does not require special wiring of the 5-pin male XLR mating connector. The headset’s left headphone channel should always be wired to pin 4 and the right headphone channel to pin 5. Conﬁguration choices, discussed later in this guide, can then be used to create the desired mon-aural output. It’s important not to connect (short) pins 4 and 5 of the Model 374A’s headset connector as damage to the Model 374A’s output circuitry could result.

Monaural (single-earpiece or “single muff”) headsets should be wired such that its headphone is wired only to pin 4; pin 5 should remain unused. Conﬁguration choices, discussed later in this guide, can be used to create a monaural output.

Some Beyerdynamic headset interconnecting cable assemblies may terminate the earpiece’s left and right connections opposite from what the Model 374A and other broadcast equipment require. These cables may terminate the left earpiece to pin 5 of the XLR connectors and the right earpiece to pin 4. If this condition is present it will require reversing or “ﬂipping” the two wires in a headset’s 5-pin male XLR connector such that the left earpiece connects to pin 4 and the right earpiece to pin 5.

Remote Control Inputs
Provision has been made to allow external switches or contact closures to mimic the operation of one or two of the four talk pushbutton switches. The exact functioning of the two remote control inputs is determined by conﬁguration settings, details of which are discussed later in this guide. A 3-conductor 3.5 mm jack is located on the Model 374A’s bottom panel and provides access to the two remote control inputs. The input circuitry is “active low,” which means that they are enabled whenever they are connected (shorted) to the common connection. Technically, each remote control input is created with a 3.4 k ohm resistor connected to +3.3 volts DC that acts as an input “pull up.” Additional resistors and capacitors provide ESD protection, minimizing the chance of damage to input due to static discharge or other extraneous signals. A current ﬂow of less than one milliampere is required for a remote control input to be recognized as active.

Prepare an interconnecting cable and associated 3-conductor 3.5 mm plug to reﬂect that the tip lead is used by Remote Control Input 1, the ring lead by Remote Control Input 2, and the sleeve lead is the connection to common. Refer to Figure 3 for connection details.

Dante Configuration

For audio to pass to and from the Model 374A requires that several Dante- related parameters be conﬁgured. These conﬁgu-ration settings will be stored in non-volatile memory within the Model 374A’s circuitry. Conﬁguration will typically be done with the Dante Controller software application which is available for download free of charge at audinate.com. Versions of Dante Controller are available to support Win-dows® and OS X® operating systems. The Model 374A uses the Ultimo 4-input/ 4-output integrated circuit to implement the Dante architecture.

The four Dante transmitter (Tx) channels associated with Model 374A’s Dante interface must be assigned to the desired receiver (Rx) channels. This achieves rout-ing the Model 374A’s four talk output audio channels to the device (or devices) that will be “listening” to them. Within Dante Con-troller a “subscription” is the term used for routing a transmitter ﬂow (a group of out-put channels) to a receiver ﬂow (a group of input channels). The number of transmitter ﬂows associated with an Ultimo integrated circuit is limited to two. These can either be unicast, multicast, or a combination of the two. If the Model 374A’s transmitter channels need to be routed using more than two ﬂows it’s possible that an intermediary device, such as the Studio Technologies’ Model 5422 Dante Intercom Audio Engine, can be used to “repeat” the signals.

The four Dante receiver (Rx) channels associated with the Model 374A’s audio inputs also need to be routed to the desired Dante transmitter (Tx) channels. These four audio signals can be sent to the Model 374A’s 2-channel headphone output.

The Model 374A supports an audio sample rate of 48 kHz with no pull-up/pull- down values available. The Model 374A can serve as the Leader clock for a Dante network but in most cases, it will be conﬁgured to “sync” to another device.
The Model 374A has a default Dante device name of ST-M374A- followed by a unique sufﬁx. The sufﬁx identiﬁes the spe-ciﬁc Model 374A that is being conﬁgured. The sufﬁx’s actual alpha and/or numeric characters relate to the MAC address of the unit’s Ultimo integrated circuit. The four Dante transmitter (Tx) channels have default names of Ch1, Ch2, Ch3, and Ch4. The four Dante receiver (Rx) channels have default names of Ch1, Ch2, Ch3, and Ch4. Using Dante Controller the default device name and channel names can be revised as appropriate for the speciﬁc application.

Model 374A Configuration
Many of the Model 374A’s operating parameters can be conﬁgured to match the needs of speciﬁc applications. The STcontroller software application is used to observe a unit’s current conﬁguration and perform any changes that are required. No DIP switch settings or other local actions are used to conﬁgure the unit. This makes it imperative that STcontroller be available for convenient use in a personal computer that’s connected to the related LAN.

Installing STcontroller
STcontroller is available free of charge on the Studio Technologies website. If necessary, download and install STcontroller onto a designated personal computer. This personal computer must be on the same local area network (LAN) and subnet as the Model 374A unit or units that are to be conﬁgured.

Using STcontroller
Immediately after starting STcontroller the application will locate and display the devices that it can control. The one or more Model 374A units that are recognized will appear in the device list. Use the Identify command to allow easy recognition of a speciﬁc Model 374A unit. Double-clicking on a device name will cause the associated conﬁguration menu to appear. Review the current conﬁguration and make changes as required.

Parameters
STcontroller allows observation and selection of functions that include:

Microphone Input – Electret Power
Microphone Input – Gain
Headphone Output Channel Routing
Sidetone – Level
Button Operation
System – Mic Kill
System – Call Indication
System – Remote Control Inputs

Changes made using STcontroller will be immediately reﬂected in the unit’s operation; no Model 374A “reboot” is required. Each time a change is made the four talk buttons on the top panel will momentarily ﬂash orange in a distinctive pattern to indicate that a command from STcontroller has been received.

Microphone Input – Electret Power
Choices are Enabled or Disabled.

If the headset has an electret microphone that requires a source of low- voltage DC power for operation enable the Electret Power check box. If the associated headset has a dynamic (non-powered) microphone do not enable the Electret Power check box. Most broadcast headsets that terminate on a 5-pin male XLR connector will not require microphone power. The on/off status is displayed by way of a red LED, labeled MIC POWER, which is located adjacent to the headset connector. Note that the Model 374A cannot supply P12 or P48 phantom power that may be required for balanced condenser (capacitor) microphones. This should not pose an issue as this type of microphone is essentially never associated with a headset that would be used for intercom applications.

Microphone Input – Gain
Choices are 22 dB, 30 dB, 42 dB, and 48 dB.

Dynamic microphones have an output level that is typically lower than that provided by electret microphones. As such, the 42 or 48 dB gain settings will probably be appropriate for them. Electret micro-phones often have internal circuitry which provides a relatively high output level. The 22 and 30 dB gain settings will typically be appropriate with this type of microphone. When a dynamic microphone is connected to the Model 374A the 42 dB gain setting may be correct for many applications. Setting the gain for 48 dB may be helpful in some applications, such as with headsets that have a low microphone output level. The 48 dB gain setting may also be useful when the Model 374A is going to be deployed at events where users are not able to speak at normal levels, e.g., sporting events such as golf tournaments where “whispering” may be necessary.

Electret microphones typically have a higher output level due to their internal preampliﬁer circuitry. As such, less cream-pliﬁer gain may be required. Selecting the 22 or 30 dB gain setting will probably be appropriate in these cases.
The compressor active LED, labeled COMP and visible adjacent to the headset connector, can act as a guide when setting the microphone preampliﬁer gain. During normal talk operation, the compressor’s active LED should light intermittently. If, for example, with a dynamic microphone the LED rarely lights and the preamp gain is set to 42 dB it might be a good idea to change it to 48 dB. If the LED is lit fully during normal talking in a situation where the headset has an electret microphone and the gain is set for 30 dB, changing it to 22 dB might be warranted.

Headphone Output Channel Routing
The choices are Left, Right, and Left and Right.

Four audio input sources (Dante receiver channels) can be assigned to the headphone output channels using the Dante Controller application. How these four audio signals are routed to the Model 374A’s headphone output channels can be conﬁgured using this conﬁguration choice. The three options provide ﬂexibility in how the audio sources are presented to the user. When using a stereo (“double muff”) headset it’s common for the audio input sources to be routed to both the left and right channels. But the Model 374A’s ﬂexibility allows each source to be independently conﬁgured for sending to the left only, right only, or both left and right headphone channels.

When using a stereo headset sending all inputs to both channels is often referred to as a dual-channel mono output. If a monaural (“single muff”) headset is used the Left conﬁguration option allows the four input channels to be combined to monaural so that the listener can simultaneously hear both sources.

Sidetone – Level
Choices are Off, Low, Medium Low, Medium, Medium High, and High.

The Model 374A includes a sidetone function that allows microphone audio coming from the microphone preamp-ﬁer to be sent to both channels of the headphone output. This serves as a user conﬁrmation that they are actively sending audio to one or more of the talk output channels. Sidetone audio will only be routed to the headphone output when at least one of the talk channels is active. The level of the sidetone audio can be selected from among ﬁve values. The correct value is simply the one that makes the user most comfortable. Sidetone audio can also be disabled by selecting Off. Selecting Off would be useful only in special applications such as during troubleshooting or where user talk audio is being returned as part of their listening to audio signals. The four rotary level controls will not impact the sidetone level.

Button Operation
Choices are Push to Talk, Push to Talk/Tap to Latch, Talk Disabled, Talk Disabled/Phones Tap to Latch, and Call (button 4 only). This conﬁguration section allows independent selection of how the four buttons will function. When the Push to Talk mode is selected the operation is self-explanatory. Only when a button is pressed and held will talk audio be sent out to its associated Dante transmitter channel.

When the Push to Talk/Tap to Latch mode is selected a “hybrid” function of sorts is enabled. Pressing and holding the button will enable audio to be sent out to its associated Dante transmitter channel. When the button is released audio will stop being sent out to its associated transmitter channel. Tapping (momentarily pressing) the button will cause the function to “latch” into the talk active mode. Tapping the button again will cause the function to “unlatch” and talk will no longer be active.

Many applications are best served when the buttons are conﬁgured in the Push to Talk mode. This ensures that a channel can’t accidentally be left in its active mode. But there are certainly valid situations when the Push to Talk/Tap to Latch mode setting will prove to be very useful. When the Talk Disabled mode is selected microphone audio will never be sent out to the associated Dante transmitter channel. This can be useful when the audio input associated with this channel is going to be monitored but talk audio is not allowed to “join” this speciﬁc intercom channel.

When the Talk Disabled/Phones Tap to Latch mode is selected the associated button will not impact talk audio but will instead control the on/off state of the audio being sent to the headphone output. In this mode talk audio will never be sent out to the associated Dante transmitter channel. This is an interesting mode, allowing one or more Model 374A audio channels to serve in a “monitor mixer” function. The button will allow quick on/off control while the rotary level control can remain in its desired position. When button 4 has been selected to the Call mode it will serve as a call enable button for talk channels 1, 2, and 3; micro-phone audio will never be sent out Dante transmitter channel 4. In the Call mode button 4 will operate in a push-to- activate manner and whenever it is active and channels 1, 2, and/or 3 are active a 20 kHz tone (call signal) will be added to the active audio paths. It will not display a call signal that’s present on audio input channel 4.

System – Mic Kill
Choices are Off, Device ID, Global Kill Command, and Device ID/Global Kill Command.

The mic kill function allows an enabled talk channel to be disabled by remote control. Speciﬁcally, it’s possible to remotely change all active (on) talk channels to their off state. This function is sometimes referred to as a “talk off” function. There are two means available to remotely disable all active talk channels. The Device ID method uses the identiﬁcation command generated by the Dante Controller or STcontroller applications as a “trigger” to disable any active talk channels. The Global Kill Command can be generated by applications that incorporate Studio Technologies’ proprietary method. This method utilizes sending a data command over the Ethernet connection. Select the desired mic kill conﬁguration from the four choices. Off simply means that no remote talk control is supported.

System – Call Indication
Choices are Off Flash, Solid, and Flash then Solid.
The call indication conﬁguration allows how each of the four talkback button LEDs will light when a call signal is detected on its respective Dante receiver (input) channel. Technically, the call is detected as active when a 20 kHz nominal audio tone is present in an audio signal path.

(It would typically be a sine- or square-wave signal that’s combined with voice audio.) If Off is selected and a call signal is detected in a Dante receiver (input) channel then the associated button’s LED will not light. If Flash is selected then a button’s LED will ﬂash orange if a call signal is detected and the channel’s talk function is not active. If the channel’s talk function is active when a call signal is detected then the button’s LED will ﬂash alternately green and orange. (Green indicates that the talk function is active and orange indicates that a call signal is detected.) If the conﬁguration is selected for Solid then a button’s LED will light orange when a call signal is detected; it will light orange whether or not the talk function associated with that button is active. If the call indication is conﬁgured for Flash then Solid and a call signal is detected, then a button’s LED will ﬁrst ﬂash orange (or green and orange) and then will light solid orange, remaining lit orange until the call signal is no longer present.

System – Remote Control In 1
Choices are Off, Channel 1, Channel 2, Channel 3, and Channel 4.

The action performed when Remote Control In 1 is enabled will follow the conﬁguration selected from among ﬁve choices. When Off is selected no action will be associated with Remote Control In 1. When Channel 1 is selected activating Remote Control Input 1 will provide the same function as would happen when pressing the Talkback 1 push button. (The exact action will depend on the button’s conﬁguration.) The same action will take place when selecting the conﬁguration to be channels 2, 3, or 4. But in these cases, remote control input 1 will control the action associated with talk channels 2, 3, or 4 respectively.

System – Remote Control In 2
Choices are Off, Channel 1, Channel 2, Channel 3, and Channel 4.

The conﬁguration choices and related actions for Remote Control In 2 are the same as those provided for Remote Control In 1.

Operation

At this point, everything should be ready and Model 374A operation can commence. An Ethernet connection with Power-over-Ethernet (PoE) capability should have been made. A headset terminated on a 5-pin male XLR connector should be plugged into the headset connector. Some applications may utilize either or both of the remote control inputs. Using the Studio Technologies’ STcontroller software application the unit’s conﬁgura-tion should have been selected to meet the needs of the speciﬁc application. The Model 374A’s Dante conﬁguration settings should have been selected using the Dante Controller software application. In this way, the unit’s four audio output channels (Dante transmitter channels) and four audio input channels (Dante receiver channels) should have been routed, by way of Dante “subscriptions,” to the receiver and transmitter channels on associated Dante-enabled equipment.

Initial Operation

The Model 374A will start to function as soon as a Power-over-Ethernet (PoE) power source is connected. However, it may take 20 to 30 seconds for full operation to commence. Upon initial power up the three status LEDs located on the bottom panel below the etherCON RJ45 receptacle will begin to light as network and Dante connections are established. The green and orange LEDs that illuminate the four pushbutton switches on the top panel may initially light randomly and then will light in a test sequence to indicate that the application ﬁrmware (embedded software) has started. Once the entire sequence has been completed and the Dante connection has been established full operation will begin.

Ethernet and Dante Status LEDs

Three status LEDs are located below the etherCON RJ45 receptacle on the Model 374A’s bottom panel. The LINK ACT LED will light green whenever an active connection to a 100 Mb/s Ethernet network has been established. It will ﬂash in response to Ethernet data packet activity. The SYS and SYNC LEDs display the operating status of the Dante interface and associated network. The SYS LED will light red upon Model 374A power-up to indicate that the Dante interface is not ready. After a short interval, it will light green to indicate that it is ready to pass data with another Dante device. The SYNC LED will light red when the Model 374A is not synchronized with a Dante network. It will light solid green when the Model 374A is synchronized with a Dante network and an external clock source (timing reference) is received. It will slowly ﬂash green when this speciﬁc Model 374A is serving as the Leader clock for the network. It’s possible that up to 30 seconds may be required for the SYNC LED to reach its ﬁnal state.

Compressor Active LED

A yellow LED indicator is located on the bottom panel adjacent to the headset connection. Labeled COMP, the LED displays the status of the microphone audio com-pressor function. It will light whenever the input level from the microphone, along with the conﬁgured preampliﬁer gain, is such that the dynamic range of the talk signal is being controlled. It’s perfectly acceptable for this LED to light intermittently whenever a user is talking at a normal voice level into the associated microphone. But if the COMP LED lights solid while a user is talking at a normal voice level this will typically indicate that the mic preamp gain setting should be reduced. Conversely, if the COMP LED rarely lights when normal talking is taking place, it’s possible that changing the mic preamp gain to the higher setting would be beneficial. Note that due to the design of the circuitry, the compressor’s active LED will function whether or not any of the four talk channels are active.

Headphone Output
Four rotary potentiometers (“pots”), located on the Model 374A’s top panel, allow individual adjustment of the level of the four audio input signals as they are sent to the 2-channel headphone output. Depending on the conﬁguration of the unit, each audio input can be sent to the left channel, the right channel, or both the left and right channels of the headphone output. The pots are “push-in/push-out” type which allows their associated knobs to be in their “out” position to be adjusted and then moved to their “in” position when protection from an unwanted change is desired.

Users should ﬁnd the headphone output audio quality to be excellent, with a high maximum output level and low distortion. Audio signals do not pass directly through the level pots. The position of the pots is recognized by the Model 374A’s pro-cessor which then adjusts the signal level within the digital domain. When a pot is in its fully counterclockwise position the associated audio signal is fully muted. In most cases, the on/off status of the four talk channels does not impact the headphone output. However, one button conﬁguration setting (Talk Disabled/Phone Tap to Latch) assigns the associated button to function as a channel listen audio on/off selector.

Button Operation

Four pushbutton switches are associated with the Model 374A’s four channels. How they function will depend on the conﬁgura-tion of the unit. Each button can be conﬁg-ured independently.

Push to Talk
When a button has been conﬁgured for the Push to Talk mode how it functions is pretty self-explanatory. Press and hold the button when headset microphone audio is to be sent out to the associated Dante audio output (transmitter) channel. The button’s green LED will light to indicate that the output is active. The button will not be lit when the function is not active.

Push to Talk/Tap to Latch
If a button has been conﬁgured for the Push to Talk/Tap to Latch mode operation is a bit different and certainly more ﬂex-ible. Press and hold the button to activate the talk function. When released the talk function will turn off. Momentarily pressing (“tapping”) the button will cause the function to change states; off-to-on or on-to-off. Whenever the talk function is active the green LED will light. The button will not be lit when the function is not active.

Talk Disabled
A button that is conﬁgured to the Talk Disabled mode will never allow talk audio to be sent to the associated Dante audio output channel. But to provide “feedback” that the button has been pressed the button’s green LED will ﬂash rapidly three times. This says, in effect, “Yes, I recognize that you pressed the button but I’m not going to do anything in response!”

Talk Disabled/Phones Tap to Latch
In the Talk Disabled/Phones Tap to Latch mode the button will never allow talk audio to be sent to the associated Dante audio output channel. Instead, the button will operate in a tap to enable/tap to disable (alternate action or “toggle”) manner and provide an audio channel listen on/off function. The button’s orange LED will light whenever audio is being sent to the headphone output. The headphone output level will continue to follow the setting of the associated rotary level control.

Call (Button 4 Only)
When button 4 is conﬁgured for the Call mode it will allow call signals to be generated whenever talk channels 1, 2, and/or 3 are active. The button functions in a push-to-call manner and will light orange whenever it is pressed and held. No microphone audio will be routed to the audio output 4. Button 4 will never light in response to a call signal being present on audio input 4. The headphone output level will continue to follow the setting of the rotary level control associated with audio input 4.

Remote Control Inputs
The Model 374A allows two switches or contact closures to be connected, by way of a 3-conductor 3.5 mm jack, to two remote control inputs. Both remote control inputs can be conﬁgured to perform the same action as talkback buttons 1, 2, 3, or 4. The remote control inputs can also be conﬁgured to be off, and thus not perform any function.

Whether or not the two remote control inputs are utilized will depend on the selected application. Even if connections are made to either or both of the remote control inputs how they speciﬁcally function will depend on several conﬁguration settings. The conﬁguration selections are performed using STcontroller with the default setting for both remote control inputs being off. The remote control inputs can be individually conﬁgured to duplicate the action of any one of the four talk pushbutton switches. When a remote control input is enabled it will cause an action identical to that caused by pressing or tapping the related push-button switch. For example, if remote control input 1 is assigned to the pushbutton function associated with talk 1 and that pushbutton is conﬁgured for latching mode, remote control input 1 will also function in a latching manner for talk channel 1.

Sidetone Function

The Model 374A includes a sidetone function that sends microphone audio to both the left and right headphone output channels whenever one or more of the talk buttons are active. The quality of the side-tone audio should be excellent and will provide Model 374A users with a conﬁdence signal that they are actively talking to other intercom users. Sidetone audio will always be sent to both headphone channels and is not a conﬁgurable choice. This is because the function is trying to simulate what a user would hear if they didn’t have a headset covering their ears. It is not intended to indicate to the user which Dante audio output (transmitter) channel or channels are actively sending audio.

The exact sidetone level is conﬁgured from among ﬁve values within the STcontroller application. There is also a selection choice for turning off sidetone. There is no means of adjusting the sidetone level using any physical buttons or controls on the Model 374A unit. Also, the four headphone level controls on the top panel of the unit do not impact the sidetone level.

In most cases, the exact sidetone level setting is not critical, and typical users will not be concerned about revising it to a speciﬁc value. But setting the sidetone level to something reasonable is important. Setting the level too low will encourage users to speak too loudly; setting it too high and users will be tempted to speak hesitantly. And while the user isn’t provided with a sidetone level control or other adjustment means, should the need arise STcontroller allows rapid adjustment of the sidetone level. In most cases, the default sidetone level, Medium, should provide an appropriate level.

Call Function

General
The Model 374A includes a call function that allows users, and users of compatible equipment, to signal each other. A call receive function is provided as part of each of the Model 374A’s four channels. Any combination of the four can have their call function active at any one time. Technically, a call signal is achieved by sending a nominal 20 kHz audio tone on the desired audio output channel. This signal, normally a sine- or square-wave, is summed (mixed) with normal talk audio. The Model 374A’s four audio input channels are always monitored for the presence of 20 kHz. A call signal is recognized when a continuous 20 kHz tone is present on the audio input for that channel.

Note that any Model 374A channel that has been conﬁgured to Talk Disabled/Phones Tap to Latch mode will not respond to the presence of a call signal. Also, if channel 4 has been conﬁgured to the Call mode that channel will not respond to a call signal on audio input 4.

The Model 374A will not confuse a normal talk audio signal with a call signal. Digital ﬁlters within the unit’s processor-integrated circuit limit each channel’s high-frequency response, helping to ensure that false call detection won’t take place. Digital ﬁltering is also performed on the Dante receiver (input) audio signals before they are sent to the headphone outputs. This prevents users with extended high-frequency sensitivity, such as presenters and guests associated with dog shows, from ever receiving undesirable audio content.

By using 20 kHz tones for call signaling the Model 374A is compatible with legacy in-tercom equipment, including the venerable RTS® BP-325 belt pack. When interconnecting Model 374A and BP-325 units using an appropriate Dante- enabled interface, such as the Studio Technologies’ Model 45DR Intercom Interface, call signaling is fully compatible. Compatibility with the Clear- Com® method of call functionality is also possible by using the Model 45DC Intercom Interface. (It converts the DC call signal associated with pin 3 of a Clear-Com party-line circuit to a 20 kHz tone.)

Devices such as the Studio Technologies’ Model 44D Audio Interface will also send and receive 20 kHz signals that are compatible with the Model 374A’s call function. To generate a call signal a Model 44D will respond to the activation of a GPI (general-purpose input) signal by summing (combining) a 20 kHz tone with the normal audio signal that is being transported “in band” via a Dante audio path. On the call receive side, audio signals that enter the Model 44D will be monitored for the presence of 20 kHz. If a call signal is detected the GPO (general-purpose output) associated with that audio channel will activate.

Receive
Whenever a Model 374A’s Dante receive (input) channel receives a valid 20 kHz nominal call signal the action of the associated button’s LED will follow the unit’s call indication conﬁguration. This one conﬁguration will impact the action of all button LEDs. If the call indication function has been conﬁgured for Disabled a button’s LED will not respond to the presence of a call signal. If the call indication conﬁgu-ration has been selected for Flash then a button’s LED will ﬂash orange when a call signal has been detected on its associated audio input and the talk function is not active. If a call tone is detected when the talk function is active then the associated button’s LED will ﬂash, alternating between green and orange. If the call indication has been conﬁgured for Solid then a button’s LED will light orange whenever a call signal is detected. If Flash then Solid is selected for the call indication conﬁguration a button’s LED will ﬁrst ﬂash orange (or orange and green if the talk function is active) and then light solid orange.

Send
The Model 374A allows a call signal to be sent on channels 1, 2, and 3. This requires that button 4 be conﬁgured to the Call mode. To send a call signal is simple: just enable any combinations of channels 1, 2, and/or 3 and simultaneously press and hold button 4. When call sending is active the orange LED associated with button 4 will light. At the same time, the channel or channels that are active in their talk mode (from among channels 1, 2, and 3) will add 20 kHz to their audio output channels and have their associated LED ﬂash, alternating between green and orange. (Green indicates that the talk function is active and orange indicates that the call function is active.) Release button 4 and the sending of call signals will cease. As expected, pressing button 4 when no talk channels are active will result in no call tones being generated.

How to Identify a Specific Model 374A
The Dante Controller software application offers an Identify command that can be used to help locate a speciﬁc Model 374A. When Identify is selected it will send a command to a single Model 374A unit. On that speciﬁc unit, the four pushbutton LEDs will light in a unique pattern. In addition, the SYS and SYNC status LEDs, located directly below the etherCON RJ45 receptacle on the bottom panel, will slowly ﬂash green. After a few seconds, the LED identiﬁ-cation pattern will cease and normal Model 374A button LED and Dante status LED operation will resume.

If conﬁgured, the Identify command can also cause the mic kill function to activate. For details please refer to the next paragraph of this guide.

Mic Kill Function
The Model 374A includes a mic kill function, allowing talk buttons that have been placed in their enabled (on) state to be remotely changed to their disabled (off) state. This allows one or more talk channels on a spe-ciﬁc Model 374A that have been enabled to be remotely disabled. The reason for this function is simple. It’s common in intercom applications for users to enable a talk channel and then go “off the headset,” forgetting that they’ve left the talk channel enabled. While they take a break or go to lunch, all other users listening to that channel may hear unwanted audio! Having the ability to disable this talk channel can be very useful.

A conﬁgurable choice in the STcontroller software application is used to select which of the mic kill methods, Device ID or Global Kill Command, will be active. Either or both can be enabled as desired. It’s also possible to disable the mic kill function. If the Device ID method of activating mic kill is enabled, whenever the speciﬁc Model 374A is identiﬁed using the Identify command within Dante Controller or STcontroller all enabled talk channels will be forced to their disabled state. If the Global Kill Command method is enabled the Model 374A will respond to any such request and force all talk channels to their disabled state.

Technical Notes

IP Address Assignment
By default, the Model 374A’s Ethernet interface will attempt to automatically obtain an IP address and associated settings using the DHCP (Dynamic Host Conﬁgu-ration Protocol). If a DHCP server is not detected an IP address will automatically be assigned using the link-local protocol. This protocol is known in the Microsoft® world as Automatic Private IP Addressing (APIPA). It is also sometimes referred to as auto-IP. Link-local will randomly assign a unique IP address in the IPv4 range of 169.254.0.1 to 169.254.255.254. In this way, multiple Dante-enabled devices can be connected and automatically function, whether or not a DHCP server is active on the LAN. Even two Dante- enabled devices that are directly interconnected using an RJ45 patch cable will, in most cases, correctly acquire IP addresses and be able to communicate with each other.

An exception does arise when trying to directly interconnect two Dante-enabled devices that use Ultimo integrated circuits to implement Dante. The Model 374A uses the Ultimo “chip” and, as such, a direct one-to-one interconnection to another Model 374A (or other Ultimo-based product) is not supported. An Ethernet switch linking the two units is required to successfully interconnect two Ultimo-based devices. The technical reason that a switch is required relates to the need for a slight latency (delay) in the data below. And an Ethernet switch will provide this. While this is certainly an anomaly, since PoE power is required for Model 374A operation it’s highly unlikely that an application would use two Model 374A units without a PoE-enabled Ethernet switch being present.

Using the Dante Controller software application the Model 374A’s IP address and related network parameters can be manually set for a ﬁxed (static) conﬁguration. While this is a more involved process than simply letting DHCP or link-local “do their thing,” if ﬁxed addressing is necessary then this capability is available. But in this case, it’s highly recommended that each unit be physically marked, e.g., directly using a permanent marker or “console tape,” with its speciﬁc static IP address. If knowledge of a Model 374A’s IP address has been misplaced there is no reset button or other method to easily restore the unit to a default IP setting.

In the unfortunate event that a device’s IP address is “lost,” the Address Resolution Protocol (ARP) networking command can be used to “probe” devices on a network for this information. For example, in Windows OS the arp –a command can be used to display a list of LAN information that includes MAC addresses and corresponding IP addresses. The simplest means of identifying an unknown IP address is to create a “mini” LAN with a small PoE-enabled Ethernet switch connecting a personal computer to the Model 374A. Then by using the appropriate ARP command the required “clues” can be obtained.

Optimizing Network Performance

For best Dante audio-over-Ethernet performance a network that supports VoIP Quality-of-service (QoS) capability is recommended. This can be implemented on virtually all contemporary managed Ethernet switches. There are even specialized switches that are optimized for enter-tainment-associated applications. Refer to the Audinate website (audinate.com) for details on optimizing networks for Dante applications. Also, disable Energy-Efﬁ-client Ethernet (EEE) support on all Ether-net switch ports that are associated with Dante devices. Some implementations of EEE can incorrectly interpret that a connected device is not present and prevent proper Dante operation.

Application Firmware Version Display

There are two ways in which the version number of the Model 374A’s application ﬁrmware (embedded software) can be identiﬁed. One requires only the Model 374A unit and involves a button-press sequence performed upon power-up. The other method utilizes the Model 374A and the STcontroller software application. Either method may prove to be useful when working with factory personnel on application support and troubleshooting. As part of the Model 374A’s power-up sequence, the unit’s application ﬁrmware (embedded software) version number can be displayed. This is useful when working with factory personnel on application support and troubleshooting. Before connecting the PoE-enabled Ethernet cable, press and hold the channel 4 button. Then connect the Ethernet cable.

Upon application of PoE power, the Model 374A will go through its normal power-up sequences followed by a display of the ﬁrmware version. The LED associated with the channel 1 button will “ﬂash” to display the major version number. Then the LED associated with the channel 2 button will “ﬂash” to display the minor version number. Once the version number has been displayed button 4 can be released and normal operation will begin. As an example of what would be a typical application ﬁrm-ware display, if the channel 1 button “ﬂash-es” twice followed by the channel 2 button “ﬂashing” one time this would indicate that application ﬁrmware version 2.1 was present in the Model 374A. A selection in the STcontroller software application allows the Model 374A’s application ﬁrmware version to be identi-ﬁed. Connect the Model 374A unit to the network and let it connect and start to function. Then, after starting STcontroller, review the list of identiﬁed devices and select the speciﬁc Model 374A that interests you. Then select Version under the Device tab. A page will then display that will provide lots of useful information. This includes the application ﬁrmware version as well as details on the ﬁrmware present in the Ultimo integrated circuit.

Application Firmware Update Procedure

It’s possible that updated versions of the application ﬁrmware (embedded software) that is utilized by the Model 374A’s process (microcontroller or MCU) integrated circuit will be released to add features or to correct issues. Refer to the Studio Technologies website for the latest application ﬁrmware ﬁle. The unit can load a revised ﬁle into the MCU’s non-volatile ﬂash memory by way of a USB interface. The Model 374A implements a USB host function that directly supports the connection of a USB ﬂash drive. The Model 374A’s MCU updates its application ﬁrmware using a ﬁle named M374A.bin.

The update process begins by preparing a USB ﬂash drive. The ﬂash drive doesn’t have to be empty (blank) but must be in the personal-computer-standard FAT32 format. Save the new application ﬁrmware ﬁle in the root directory with the name of M374A.bin. Be certain to use the eject command to ensure that the ﬁle is correctly stored on the USB ﬂash drive. Studio Technologies will supply the application ﬁrmware ﬁle inside a .zip archive ﬁle. While the application ﬁrmware ﬁle inside of the zip ﬁle will adhere to the naming convention required by the Model 374A, the name of the zip ﬁle itself will include the ﬁle’s version number. For example,
a ﬁle named M374Av2r1MCU.zip would indicate that version 2.1 of the application ﬁrmware (M374A.bin) is contained within this zip ﬁle.

Once the USB ﬂash drive is inserted into the USB interface, located on the main circuit board under the cover, the unit must be powered off and again powered on. At this point, the ﬁle will automatically load into the processor’s ﬂash memory. The precise steps required will be highlighted in the next paragraphs of this guide.

To install the application ﬁrmware ﬁle follow these steps:

Disconnect power from the Model 374A. This will entail removing the Ethernet connection that is providing PoE power.
Remove the cover from the Model 374A. Begin by removing the four Phillips-head machine screws (#1 screwdriver tip), two per side. Be certain to save the screws so that re-assembly will be fast and painless. Then carefully slide the cover forward to separate it from the level controls and buttons and then lift it off.
Locate the USB connector on the main circuit board. It’s near the channel 1 button. Insert the prepared USB ﬂash drive into it.
Apply power to the Model 374A by connecting to a Power-over-Ethernet (PoE) Ethernet source.
After a few seconds, the Model 374A will run a “boot loader” program that will automatically load and save the new application ﬁrmware ﬁle (M374A.bin). This will take only a few seconds. During this period the channel 4 button LED will ﬂash slowly in alternating colors. Once the entire process is over, taking approximately 10 seconds, the Model 374A will restart using the newly saved application ﬁrmware.
At this time the Model 374A is operating under the newly saved application ﬁrmware and the USB ﬂash drive can be removed. But to be conservative, remove PoE power ﬁrst and then remove the USB ﬂash drive.
Conﬁrm that the desired application ﬁrmware version has been correctly saved. This can be done by pressing and holding the channel 4 button, ap-plying PoE power to the Model 374A, and then “reading” the application ﬁrmware version number by ﬁrst observing the channel 1 button’s LED and then observing the channel 2 button’s LED. Alternatively, the STcontroller software application can be used to identify the application ﬁrmware version number. Whatever method you use, ensure that the desired version is present.
Once the update process has been completed reverse the steps and re- attached the cover using the four machine screws.

Note that upon power being applied to the Model 374A if a connected USB ﬂash drive doesn’t have the correct ﬁle (M374A.bin) in the root folder, no harm will occur. If the correct ﬁle is not present upon power up the channel 4 button’s LED will ﬂash on and off rapidly for a few seconds to indicate this condition and then normal operation using the unit’s existing application ﬁrmware will begin.

Ultimo Firmware Update
As previously discussed in this guide, Model 374A implements Dante connectivity using the 4-input/4-output Ultimo integrated circuit from Audinate. The Dante Controller software application can be used to determine the version of the ﬁrmware (embedded software) that resides in the Ultimo “chip.” The STcontroller software application can also be used to identify the Ultimo’s ﬁrmware version. (Use the Version selection under the Device tab.) The Ultimo ﬁrmware can be updated by way of the Model 374A’s Ethernet connection. The latest Ultimo ﬁrmware ﬁle is available on the Studio Technologies website. The Dante Firmware Update Manager (FUM) application program can be used to install the Ultimo ﬁrmware.

The Dante Controller software application includes an automated method of updating Ultimo ﬁrmware. It offers a much simpler method of keeping the Ultimo ﬁrmware current.

Belt Clip
The belt clip is attached to the back of the Model 374A’s enclosure by way of two 6-32 thread, Philips-head machine screws. Unlike other the original Model 374 Inter-com Beltpack units, the belt clip on the Model 374A will never have to be rotated as part of the conﬁguration process. (There are no conﬁguration DIP switches or a pushbutton switch under the belt clip.) But if the belt clip does need to be replaced a #1 Philips-head screwdriver would be the correct tool to remove the machine screws.

Restoring Factory Defaults
A command in the STcontroller software application allows the Model 374A’s conﬁguration to be reset to the factory default values. From STcontroller select the Model 374A for which you want to restore its defaults. Select the Device tab and then select the Factory Defaults feature. Then click on the OK box. Refer to Appendix A for a list of Model 374A’s factory default values.

Speciﬁcations

Power Source:

Power-over-Ethernet (PoE): class 1 (very low power, ≤3.84 watts) per IEEE® 802.3af

Network Audio Technology:

Type: Dante audio-over-Ethernet
AES67-2018 Support: yes
Dante Domain Manager (DDM) Support: yes Bit Depth: up to 24
Sample Rate: 48 kHz
Number of Transmitter (Output) Channels: 4
Number of Receivers (Input) Channels: 4
Dante Audio Flows: 4; 2 transmitter, 2 receiver

Network Interface:

Type: 100BASE-TX, twisted-pair Ethernet, Power-over-Ethernet (PoE) supported
Data Rate: 100 Mb/s (10 Mb/s and 1000 Mb/s GigE Ethernet not supported)
Audio Channels: 4 talk, 4 listen

Microphone Input:

Compatibility: dynamic or electret (low-voltage DC-powered) microphones
Type: unbalanced
Electret Microphone Power: 3.3 volts DC via 2.00 k resistor, selectable on/off
Gain: 22, 30, 42, or 48 dB, selectable
Frequency Response: 50 Hz to 10 kHz, –3 dB
Distortion (THD+N): <0.02%, 1 kHz, 22 dB gain
Noise Floor: –95 dBFS (A-weighted)

Compressor:

Threshold: 1.5 dB above nominal level (–18.5 dBFS)
Slope: 2:1
Status LED: compressor active

Headphone Output:

Type: 2-channel
Compatibility: intended for connection to stereo (dual-channel) or monaural (single-channel) headsets with a nominal impedance of 50 ohms or greater
Maximum Output Voltage: 3.8 Vrms, 1 kHz, 150 ohm load
Frequency Response: 20 Hz to 10 kHz, –3 dB
Distortion (THD+N): <0.002%
Dynamic Range: >100 dB

Call Function:

Receive Support: channels 1-4
Send Support: channels 1-3
Signaling Method: 20 kHz, ±800 Hz, within audio channels
Receive Level: –27 dBFS minimum
Send Level: –20 dBFS
Remote Control Inputs: 2
Function: configurable, can mimic the action of any talk button function
Type: active low, 1 mA maximum, input pulled up to 3.3 volts DC via 3.4 k ohm resistors

Connectors:

Headset: 5-pin female XLR
Remote Control Inputs: 3-conductor (TRS) 3.5 mm jack
Ethernet: Neutrik NE8FBH etherCON RJ45 receptacle
USB: type A receptacle (located inside Model 374A’s enclosure and used only for application firmware updates)
Configuration: requires Studio Technologies’ STcontroller software application

Environmental:

Operating Temperature: 0 to 50 degrees C (32 to 122 degrees F)
Storage Temperature: –40 to 70 degrees C (–40 to 158 degrees F)
Humidity: 0 to 95%, non-condensing
Altitude: not characterized
Dimensions (Overall):
- 3.6 inches wide (9.2 cm)
- 1.6 inches high (4.0 cm)
- 4.8 inches deep (12.6 cm)
Mounting Options: intended for portable applications; contains integral belt clip; optional MBK-01 Mounting Bracket Kit allows Model 374A to be permanently mounted
Weight: 0.6 pounds (0.3 kg)