BAXTON STUDIO BBT6661A1DARKGREYQUEEN2PCSET Sinclaire Series 2 Piece Bedroom Set Instruction Manual
- October 30, 2023
- BAXTON STUDIO
Table of Contents
BBT6661A1DARKGREYQUEEN2PCSET Sinclaire Series 2 Piece Bedroom Set
Instruction Manual
ASSEMBLY INSTRUCTIONS
Read this instruction carefully. See hardware and furniture part list for
guidance. Be sure all parts are complete, before you assemble. Place all
wooden furniture parts on a clean and flat soft surface to prevent from being
scratched.
Follow the figure to start assembling.
CAUTIONS :
- Do not FULLY – TIGHTEN the nut or nut bolt until all nut or bolt is ready assembly.
- Do not OVER – TIGHTEN the nut or bolt to avoid causing damages to the thread.
- Keep all hardware parts out of reach of children.
NOTE : THE LIST AND QUANTITY SHOWN ARE FOR 1 UNIT ASSEMBLY.
Tool needed : Screwdriver (not provider).
PART LIST
| ITEM | DESCRIPTION | QTY |
|---|---|---|
| A | HEADBOARD | 1 PC |
| B | FOOTBOARD | 1 PC |
| C | SIDE RAIL | 2 PCS |
| D | CENTER RAIL | 1 PC |
| E | CENTER SUPPORT | 2 PCS |
| F | CENTER SUPPORT LEG | 3 PCS |
| G | BED SLAT | 26 PCS |
| H | BED LEG | 4 PCS |
HARDWARE LIST
| ITEM | DESCRIPTION | QTY |
|---|---|---|
| 1 | JCBC BOLT M6 x 20mm | |
| 2 | M6 FLAT WASHER | |
| 3 | M6 SPRING WASHER | |
| 4 | WOOD SCREW M3.5 x 16mm | |
| 5 | WOOD SCREW M4 x 25mm | |
| 6 | BED SLAT SIDE FITTER | |
| 7 | BED SLAT CENTER FITTER | |
| 8 | WOOD SCREW M4 x 20mm | |
| 9 | M4 ALLEN KEY (BALL SHAPE) | |
| 10 | M5 ALLEN KEY (BALL SHAPE) |
ASSEMBLY INSTRUCTIONS
Read this instruction carefully. See hardware and furniture part list for
guidance. Be sure all parts are complete, before you assemble. Place all
wooden furniture parts on a clean and flat soft surface to prevent from being
scratched.
Follow the figure to start assembling.
CAUTIONS :
- Do not FULLY – TIGHTEN the nut or nut bolt until all nut or bolt is ready assembled.
- Do not OVER – TIGHTEN the nut or bolt to avoid causing damages to the thread.
- Keep all hardware parts out of reach of children.
NOTE: THE LIST AND QUANTITY SHOWN ARE FOR 1 UNIT ASSEMBLY.
Tool needed: Rubber Mallet (not provider).
PART LIST
| ITEM | DESCRIPTION | QTY |
|---|---|---|
| A | BENCH | 1 PC |
| B | LEGS | 4 PCS |
| C | LEG SUPPORT | 2 PCS |
HARDWARE LIST
| ITEM | DESCRIPTION | QTY |
|---|---|---|
| 1 | JCBC BOLT M6 x 50mm | | 4PCS
2| JCBB BOLT M8 x 50mm| | 8 PCS
3| M6 SPRING WASHER| | 4 PCS
4| M8 FLAT WASHER| | 8 PCS
5| M8 SPRING WASHER| | 8 PCS
6| WOOD DOWEL M8 x 30mm| | 4 PCS
7| M4 ALLEN KEY (BALL SHAPE)| | 1 PC
8| M5 ALLEN KEY (BALL SHAPE)| | 1 PC
