HUDSON VALLEY Kyoto 13 Light Chandelier Instruction Manual

**HUDSON VALLEY Kyoto 13 Light Chandelier Instruction Manual

**

WARNING/CAUTION

• DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
• TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND  LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION ANDMAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
• CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE. ·
• UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES.  FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
• PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

www.hvlgroup.com

FIXTURE INSTALLATION

1. Side crimp type CABLE CLAMP (T) onto the safety cable. Feed the SAFETY CABLE (3) down through one of the holes in the top of the outlet box. Loop the SAFETY CABLE (3) over the approved support. Feed the SAFETY CABLE (3) back through the top of the box and the CABLE CLAMP (T). Using the  crimping tool, Slightly crimp the CABLE CLAMP (T) to lock the SAFETY CABLE (5) in position
2. Feed the wire through the STEM KIT and twist tightly onto the FIXTURE ASSEMBLY (M). Keep adding additional until you desired hanging heights 1
3. Side in CANOPY onto the STEM KIT and thread the NIPPLE (H) onto the top and of the STEM KIT
4. Pull the wire out from the junction box, and install the MOUNTING PLATE (A) onto the junction box and NIPPLE (E) (BY OTHER) using the MOUNTING SCREWS (and secure with the WASHERS (7) BY OTHER HEX NUTS (G) (BY OTHER) This is designed to be mounted on heavy duty junction box rated for a minimum 90s. The junction box must be securely mounted to the structure of the building. MAKE SURE THE NIPPLE (E) BY OTHER) ARE STRONG ENOUGH!
5. Trim off the excess wire to a minimum beyond the STEM and strip each wire Attach the Ground wine (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A) NEVER CONNECT GROUND WIRE TO HOT WIRE! FALURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
6. Connect the whitexture lead to the neutral (Generally white) wire in the outlet box. Fasten the wire together with an approved fastener WIRE NUT) (DJ Starting below the fastener, tightly wrap the connection with alectrical tape so that the connections seals the end of the tastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUM
7. Connect the black fisture leads to the hot (Generally black) wine in the outlet box. Fasten the joined wires some as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH
8. Push the wires back into the junction box. Lift up the CANOPY (up to the calling, and secure it with the HEADLESS SCREW by using supplied ALLEN KEY
9. Screw the BULB (N) into the SOCKET of the four. THIS FOCTURE IS RATED FOR 25 WATT TYPE GOS LAMP. DO NOT EXCEED THE RECOMMENDED
10. Screw the TUBE (L) to the FIXTURE ASSEMBLY (M) then screw the GLASS G (R) to the TUBE (L) of the
11. Screw the GLASS A, B, C (OP) into the FIXTURE ASSEMBLY (M) of the Sure
12. Restore power to the outlet at the breaker or fuse box

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>