elk HOME 89905-1 Pendant Ceiling Light Instruction Manual

elk HOME 89905-1 Pendant Ceiling Light

WARNING
DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.

WARNING
This fixture is intended for installation by the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Before assembly, remove all parts and part packages from the box. If anything is missing, please contact the retailer from which the product was purchased.

Installation

1. Carefully pull house wires down out of the junction box so house wires are easily accessed to connect fixture wires.

2. If the screw collar loop (W) is already attached to the mounting bracket (A), proceed to Step 3. To assemble screw collar loop (W) to mounting bracket (A): Hold mounting bracket (A) so the head of the ground screw is pointing down towards the floor. Hold threaded pipe so two hex nuts already attached to threaded pipe (E) are pointing down towards the floor. From the side of the mounting bracket with the ground screw head, screw the short end of the threaded pipe (E) into the hole in the centre of the mounting bracket (A) until the hex nut on the threaded pipe (E) touches the mounting bracket.

3. Thread hex nut (V) onto the end of the threaded pipe (E). Tighten hex nut (V) to secure threaded pipe (E) to mounting bracket (A). Thread screw collar loop (W) onto the end of threaded pipe pointing down towards the floor.

4. Tighten the screw collar loop up against hex nut on the threaded pipe (E).

5. Place mounting bracket (A) up against the junction box. Screw collar loop (E) should be pointing down towards floor. Align each slot in mounting bracket (A) with each hole in the junction box.

6. Thread one junction box screw (B) into each slot in the mounting bracket (A) and into holes in the junction box. Tighten junction box screws (B) to secure mounting bracket (A) to the junction box.
   CAUTION: Make sure house wires are still easily accessible. DO NOT pinch wires between mounting bracket and ceiling.

7. Carefully push fixture wires from top of fixture body (O) up through bottom of centre stem (M). Pull fixture wires taut. Screw center stem (M) onto the top of fixture body (O).

8. Push fixture wires up through bottom of loop (L). Pull fixture wires taut. Screw the bottom of the loop (L) onto top of center stem (M).

9. Connect one locking link (G) to loop (L) on top of center stem (M).

10. Determine desired hanging height of fixture. Cut chain (H) to length to achieve desired height.

11. Slip chain link at end of chain (H) onto locking link (G) on loop.

12.  Weave fixture wires through chain links, skipping every other chain link.

13. Slip threaded ring (F) down over end of chain (H).

14. Position canopy (D) so outside of canopy is pointing down towards fixture. Slip hole in canopy (D) over end of chain (H). Strip 3/4” of insulation from ends of fixture wires.

15. Carefully push fixture wires up through hole in screw collar loop (W) attached to mounting bracket (A) and out end of threaded pipe inside junction box. Carefully pull fixture wires so they are easily accessible to connect to house wires.

16. To aid in connecting fixture wires to house wires, temporarily connect second locking link (G) to link at end of chain (H) and to screw collar loop (W).

17. Slightly loosen ground screw on the mounting bracket (A). Do not completely remove ground screw. Wrap house ground wire (copper) around ground screw, leaving enough ground wire to attach to fixture ground wire.

18. Twist end of fixture ground wire and end of house ground wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart below for correct wire connections.

19. Twist end of house lead wire (black) and end of fixture lead wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C).

20. Twist end of house neutral wire (white) and end of fixture neutral wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart to the right for correct wire connections.

21. Wrap electrical tape (not included) around wire nuts (C) and wires. Ensure wires are securely fastened into wire nuts.

22. Carefully push all wires and wire nuts into junction box.

23. Remove second locking link (G) from last link on chain (H) and screw collar loop (W).

24. Raise canopy (D) up to ceiling. Pass hole in canopy (D) over screw collar loop (W). Position canopy (D) up against ceiling.

25. Raise threaded ring (F) up to canopy (D). Screw threaded ring (F) onto screw collar loop (W). Tighten threaded ring (F) to secure fixture to ceiling.

26. Attach second locking link (G) to link at end of chain (H). Attach locking link (G) at end of chain (H) to loop on screw collar loop (W).

27. Pass hole in top of shade (K) over socket. Slip spacer (N) over socket. Thread socket ring (P) onto socket. Tighten socket ring (P) to secure shade (K) in place. DO NOT over tighten.

28. Screw recommended bulb (E26 Edison bulb type, not included) into socket. Verify correct bulb wattage marked on socket of fixture.
    WARNING: DO NOT exceed maximum bulb wattage.

References

• elkhome.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>