MiCODUS MV790G Vehicle GNSS Tracker User Manual

MiCODUS MV790G Vehicle GNSS Tracker

Main Features

• GPS+LBS +GLONASS

• Remotely Cut Off /Resume Fuel

• Historical Route Playback

• Realtime Tracking

• 9-90V Wide Working Voltage

• Vibration Alarm

• Overspeed Alarm

• Tow Alarm

• Power Disconnect Alarm

• Geo-fence

• SOS Panic Button

• Engine On/ OFF Alarm

• Voice Monitor

• 4G LTE+ 2G GSM

Specifications

850/900/1800/1900MHz

4G LTE CAT1: B1/B2/B3/B4/B5/B7/B8/B12/ B13/B18/B19/B20/B25/B26/B28/B66/B34/ B38/B39/B40/B41

SIM Card| Nano SIM Card
Cellular Antenna| Built-in
GNSS Specifications| Positioning Type| GPS+GLONASS+LBS
GPS Antenna| Built-in
Cold Start| ≤32 Seconds
Hot Start| ≤1 Second
Tracking sensitivity| -162 dBm
GPS Channels| 64
Position Accuracy| 5-10m
External interface| SOS, Microphone

How to manage the tracker to get online?

Step 1 SIM card requirements

Please get a suitable SIM card from your local place. The SIM card must meet below points:

• It must be compatible with the 4G LTE or 2G GSM network
• Please enable SMS, call, internet data traffic of the SIM card
• Remove the PIN code
• Enable the caller ID display feature
• Use Nano size SIM card for the tracker
• Please inquire the SIM card provider for the exact correct APN information.

Step 2 Wiring

Step 3 Configure APN

Please get the exact correct APN name from local SIM card provider. Take the tracker to a good signal place for operation and configure the APN for it as below:

user and APN password then please use this command
pan, pan name, nonuser, pan password| pan ok| pan, orange, orange, orange| If the APN information has APN user and APN password then please use this command

Note: Please get the exact correct APN name from local SIM card provider. The APN information is very important, it must 100% correct to match with the sim card of the tracker, if you configured wrong APN, the tracker also will reply “SET APN ok” but it will can’t get online!

Step 4 Indicator status description

Device has not been turn on
Device ran out of battery

Package Content

Functions Explanation

Please follow with the quick user guide carefully!

a. Vibration Alert:

This vibration alert function just work under stationary status. How to use this function:

Step 1: Set admin number by this SMS command:
admin123456,number with country code

Step 2: Enable the device to enter into arm mode by this
SMS command: 111

Step 3: Configure the alarm ways by this sums command:
vib,2,4

Step 4: Keep the device under stationary status more than 5min to let it enter into sleep arm mode;

Step 5: Vibrate the device then the tracker will send the vibration alarm messages .

NOTE you also can configure more two SOS numbers for the tracker, the
alarm messages also will be sent to them!

b. Cut Off Fuel/Resume Fuel

Step 1: Set admin number by this SMS command:
admin123456,number with country code

Step 2: Choose the cut off fuel mode you want:
Safely cut off fuel mode: cutoil123456,0
Immediately cut off fuel mode: cutoil123456,1

Step 3: Send this SMS command from the admin number to cut off fuel: 555

NOTE About the cut off fuel function, firstly please make sure the fuel circuit is connecting to main power. About the cut off fuel function, firstly please make sure the fuel circuit is connecting to main power. Secondly, it has 3 different performance, please read it carefully:

For safely cut off fuel mode, it has 3 different performance, please read it carefully:

• If the network signal and satellite signal both are available, when the equipment speed exceeds 20km/h, the fuel circuit will not be cut off immediately, it will cut off intermittently till the speed is below 20km/h, then just can be completely cut off.
• In the tracker has network signal and but no satellite signal, the fuel circuit will be cut off intermittently, after 2, 3 minutes it will be cut off completely;
• If the tracker stopped more than 5 minutes, the fuel circuit will be cut off immediately, and then connected, but if you vibrate the tracker or vibrate the tracker the fuel circuit will be cut off immediately;

For immediately cut off fuel mode, it will cut off fuel completely under any conditions only if the device has signal.

c. Engine On/Off Alarm

Step 1: Set admin number by this SMS command:
admin123456,number with country code
Step 2: Configure the alarm ways via this SMS command:
autorep123456,AB

For example:

A=0 (Engine ON: No Alarm);
A=1 (Engine ON: SMS only);
A=2 (Engine ON: Platform only);
A=3 (Engine ON: SMS + Platform)
B=0 (Engine OFF: No Alarm);
B=1 (Engine OFF: SMS only);
B=2 (Engine OFF: Platform only);
B=3 (Engine OFF: SMS+ Platform)

NOTE you also can configure more two SOS numbers for the tracker, the alarm messages also will be sent to them!

Installation Recommendation

1. The decide should face up to the sky.
2.  Metal thermal barrier of heating layer of the windshield affects the signal.

Troubleshooting

Check whether the data service of SIM card is enabled. Check the balance of SIM card.

Tracker shows offline| Check whether external power is still connected. Check if the vehicle entered network blind area. Check the balance of SIM card.
Unable to locate| Make sure the top side facing upward without metallic things shielded.

Make sure it’s not in area with no satellite coverage.

Location drift| In area with poor GNSS signal (tall building around or basement), drifting may happen.

Check whether vibration happens around to trigger the accelerator.

No command reply| Make sure command format is correct. Vehicle may be in network blind area.

Make sure SIM card is well inserted and has SMS servo.

Full SMS Commands List

Query Commands
Parameter Query| param,1| firmware version 、ID、 IP、 port、 domain、 APN
param,2| admin number, SOS number, move distance, overspeed, auto arm time, auto disarm time, alarm interval
Status| status| BAT:10 GPRS: GSM: GPS:A/V ACC: on/off

oil: on/off power: on/off

IMEI Checking| imei123456|
Check Command Password| get pad|
Google Maps Link| G123456# or where| V:A: Indicates the device has GPS signal;

V:V: Indicates the device doesn’t have GPS signal; 2019-11-26 10:17:01: Date and Time;

S: 000km/h: Speed of the tracker

Bat:5: Battery level of the backup battery of the tracker, it has 6 levels: “6” means 100% , “5” 80%,

“4” means 60%, “3” means 40%, “2” means 20%,

“1” means 10%;

ACC: off: The status of the car engine; 7201000006: ID number of the device;

S26: GSM signal is 26 G06: GPS signal is 06 p:46000, l:13152, c:63162: p, l, c this 3 parameters means the LBS code

Setting Commands
Set Admin Number| admin123456,number| Example: admin123456,008613566669999

Please add your country code as prefix of the admin number

Set SOS Numbers| SOS,SOS1,SOS2| Example: SOS,008613566668888,008613566669999

Please add your country code as prefix of the admin number

Back to Factory Setting| begin123456| After sent this SMS command, all your configuration will be cleared and the device will get back to factory default settings
Command Password Change| setpwd123456,new password| The password just can be 6 digitals
Restart| rst| After sent this SMS command, the configurations will be saved and the device will restart
Data Traffic Switch| gprs123456,A| A=1 ON ; A=0 OFF; Default: 1
Functions| Command Format| Explanation
---|---|---
APN| pan, pan content, nonuser, pan passed| Example: pan, orange, orange, orange

Please get the exact correct APN name from the SIM card provider of the tracker!!!For example: pan, orange, orange, orange

pan, pan content| Example: pan, internet

If the SIM card operator doesn’t have APN user and password, then you can ignore it!!! For example: apn, comet

IP/Domain &Port| adminip123456, ip/domain name: port| Example: arminid 123456,47.254.77.28:7700 or arminid 123456,d.micodus.net:7700

Micoud’s tracking platform: Domain name: d.micodus.net, IP: 47.254.77.28, Port: 7700

Data Upload Frequency| upload 123456,A| Example: 1. upload123456,10 (Means the device will upload data every 10s under moving status and heartbeat data every 3min under static status)

2. upload123456,1800 (Means the device will upload data every 1800s under both moving status and static status)

A: Time interval value: 1-3600s; if A is less than 600s, for example, A=10s, then device will upload data every 10s when moving, after the car stop more than 5min, it will just upload heartbeat data every 3min; if A is more than 600s, for example, A=1800s, then the device will upload data according to 1800s under both moving and stationary status

Time Zone| time zone 123456,A| If west time zone, you need input sign “-“,

for example: timezone123456,-4; if east time zone, then needn’t input sign “+”, for example: timezone123456 8

Arm| 111 or SF|
Disarm| 000 or CF|
Cut Off Fuel Mode| cutoil123456,A| Example:

If you want to cut off fuel immediately, please send below two commands:

Firstly send: cutoil123456,1 Secondly send: 555

If you want to cut off fuel safely, please send below two commands:

Firstly send: cutoil123456,0 Secondly send: 555

A=0-1: 0: Cut off fuel safely; 1: Cut off fuel immediately

Cut Off Fuel| 555| cut oil ok
Resume Fuel| 666| resume oil ok
Auto Arm By ACC| act, time| Example: acclt,30 (Means the tracker will enter into arm status automatically after engine off 30s)

Time scope: 5-1200 seconds

the device will enter into sleep mode automatically, SMS commands and call can wake up it
sleep123456,shock| If device keep stationary more than 5 minutes the device will enter into sleep mode automatically, vibration, SMS commands and call can wake up it
sleep123456,off| Cancel sleep mode
| Alarm| Setting Commands
Movement Alarm| move,<distance(m)>, [mode]| Example: move,300,1 (Means if the tracker was moved 300m it will send alarm message to admin and so’s numbers via platform and SMS )

Move distance 100-3000m；

Mode:1-4: 1 Platform+ SMS 2、Platform+Call；3、Platform+ SMS+Call；4、Platform only Default: 4

Overspeed Alarm| speed,