VIVO DESK-E3CTB Electric Height Adjustable Corner Stand Up Desk Instruction Manual

VIVO DESK-E3CTB Electric Height Adjustable Corner Stand Up Desk

Product Information

Specifications

• Product Name: 63 x 55 Corner Electric Desk
• Model: DESK-E3CT SERIES
• Frame Options: DESK-E355B, DESK-E355G, DESK-E355W
• Table Top Options: DESK-E3CTB-A, DESK-E3CTC-A, DESK-E3CTD-A, DESK-E3CTG-A, DESK-E3CTN-A, DESK-E3CTW-A
• Weight Capacity: 176lbs (80kg)

Product Usage Instructions

Pre-Assembly

Before you begin assembling the desk, please read and understand the following instructions:

• If you do not understand these directions or have any doubts about the installation safety, please call a qualified technician.
• Check carefully to ensure there are no missing or defective parts.
• Improper installation may cause damage or serious injury.
• Do not use this product for any purpose that is not explicitly specified in the manual.
• Do not exceed the weight capacity of 176lbs (80kg).
• WARNING: CHOKING HAZARD – Small parts. Not for children under 3 years. Adult supervision is required.

Tools Needed

You will need the following tools to assemble the desk:

• Phillips Screwdriver
• Level

Difficulty Level

The assembly difficulty level for this product is moderate.

Package Contents

Please ensure that you have received all the necessary parts listed below before starting the assembly:

• (x1) Left Desktop (A)
• (x1) Middle Desktop (B)
• (x1) Right Desktop (C)
• (x1) Left Crossbar (D)
• (x1) Right Crossbar (F)
• (x1) Angled Right Crossbar (G)
• (x2) Sync Rod (H)
• (x2) Side Brackets (I)
• (x1) Short Left Crossbar (E)
• (x1) Right Leg (J)
• (x1) Motorized Leg (K)
• (x1) Left Leg (L)
• (x1) Short Connector Bracket (M)
• (x1) Long Connector Bracket (N)
• (x4) Desktop Connector (O)
• (x2) Foot (P)
• (x1) Control Panel (Q)
• (x1) AC Adapter (R)
• (x1) Extension Cable (S)
• (x25) Anti-Vibration Pads (T)
• (x2) Cable Clips (U)
• (x22) M6x8mm Screw (S-A)
• (x9) M6x35mm Screw (S-B)
• (x43) M5x16mm Screw (S-C)

PRE-ASSEMBLY | BEFORE YOU BEGIN

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified  technician. Check carefully to make sure there are no missing  serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

WARNING: CHOKING HAZARD SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

ELECTRICAL WARNING :

THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.

• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.

WEIGHT CAPACITY

DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury.

• Product Warranty
  For the most up to date details on your product’s warranty, please visit the product’s listing on our website or reach out to customer support. vivo- us.com/products/desk-e3ctb

• Returns | Product Didn’t Work Out?
  We offer a hassle-free 30 day return on all products. Contact customer support at 309-278-5303 or help@vivo-us.com. Please note: For items ordered in error or no longer needed, the return shipping charges will be at the buyer’s expense.

TOOLS NEEDED

PACKAGE CONTENTS

Please consult the parts list below and ensure you have everything you need to assemble your product. If parts are missing or damaged, please contact us .

ASSEMBLY STEPS

STEP 1: Assemble the Left Leg

• Connect Left Crossbar (D) to Left Leg (L) using M6x8mm Screws (S-A) and 5mm Allen Wrench (T-A).
• Attach Side Bracket (I) to Left Leg (L) using M6x8mm Screwns (S-A) and 5mm Allen Wrench (T-A).

STEP 2: Assemble Right Leg

• Attach Angled Right Crossbar (G) to Right Leg (J) using M6x8mm Screws (S-A) and 5mm Allen Wrench (T-A).
• Attach Side Bracket (I) to Right Leg (J) using M6x8mm Screws (S-A) and 5mm Allen Wrench (T-A).

STEP 3: Install Feet & Connect Motorized Leg

Assembly Options

This desk can be assembled with a left or right side extension. Please select an option and proceed with assembly

ASSEMBLY OPTION A | Left Side Extension

A-STEP 4: Install Anti-Vibration Pads

• Affix Anti-Vibration Pads (T) to desk frame, Short Connector Bracket (M), and Long Connector Bracket (N). Connector Brackets will be installed in next step.

A-STEP 5: Assemble Desktop

• Connect Left, Middle, and Right Desktop (A, B, C) pieces together using Desktop Connectors (O), M5x16mm Screws (S-C) and a Phillips screwdriver.

A-STEP 6: Install Connector Brackets

• Begin connecting frame to desktop by placing assemblies on desktop as shown below. Connect Angled Right Crossbar (G) and Right Crossbar (F) to Short Connector Bracket (M), M6x8mm Screws (S-A), and 5mm Allen Wrench (T-A). Connect Long Connector Bracket (N) to Short Left Crossbar (E) and Left Crossbar (D), using M6x8mm Screws (S-A), and 5mm Allen Wrench (T-A).

A-STEP 7: Secure Frame & Desktop

• Secure to desktop with M5x16mm Screws (S-C) and a Phillips screwdriver, using the screw locations shown below. Connect Control Panel (Q) to desktop using M5x16mm Screws (S-C) and a Phillips screwdriver.

A-STEP 8: Install Sync Rod

• Loosen the coupling nut on Sync Rods (H) and insert hex shaft into Left and Right Leg (L, J), making sure the metal retaining ring makes contact with the leg. Ensure that all three legs are the same height. If not, turn the Sync Rod (H) clockwise to raise corresponding leg, and counter-clockwise to lower. Loosen coupling nuts on Sync Rods (H) and extend onto Motorized Leg (K). Tighten coupling nuts, then tighten both set screws on the end of Sync Rods (H) using 2mm Allen Wrench (T-B).

A-STEP 9: Connect Power Cables

• Connect Power Cord (R) and cable from Motorized Leg (K) to Control Panel (Q). If needed, use Extension Cable (S) for cable from Motorized Leg (K) to extend length. Use Cable Clips (U) to secure cables to desktop.

ASSEMBLY OPTION B | Right Side Extension

B-STEP 4: Install Anti-Vibration Pads

• Affix Anti-Vibration Pads (T) to desk frame, Short Connector Bracket (M), and Long Connector Bracket (N). Connector Brackets will be installed in next step.

B-STEP 5: Assemble Desktop

• Connect Left, Middle, and Right Desktop (A, B, C) pieces together using Desktop Connectors (O), M5x16mm Screws (S-C) and a Phillips screwdriver.

B-STEP 6: Install Connector Brackets

• Begin connecting frame to desktop by placing assemblies on desktop as shown below. Connect Angled Right Crossbar (G) and Right Crossbar (F) to Long Connector Bracket (N), M6x8mm Screws (S-A), and 5mm Allen Wrench (T-A). Connect Short Left Crossbar (E) and Left Crossbar (D) to Short Connector Bracket (M), M6x8mm Screws (S-A), and 5mm Allen Wrench (T-A).

B-STEP 7: Secure Frame & Desktop

• Secure to desktop with M5x16mm Screws (S-C) and a drill, using the screw locations shown below. Connect Control Panel (Q) to desktop using M5x16mm Screws (S-C) and a drill.

B-STEP 8: Install Sync Rod

• Loosen the coupling nut on Sync Rods (H) and insert hex shaft into Left and Right Leg (L, J), making sure the metal retaining ring makes contact with the leg. Ensure that all three legs are the same height. If not, turn the Sync Rod (H) clockwise to raise corresponding leg, and counter-clockwise to lower. Loosen coupling nuts on Sync Rods (H) and extend onto Motorized Leg (K), making sure set screw faces out. Tighten coupling nuts, then tighten both set screws on the end of Sync Rods (H) using 2mm Allen Wrench (T-B).

B-STEP 9: Connect Power Cables

• Connect Power Cord (R) and cable from Motorized Leg (K) to Control Panel (Q). If needed, use Extension Cable (S) for cable from Motorized Leg (K) to extend length. Use Cable Clips (U) to secure cables to desktop.

CONTROLLER – USER MANUAL

• Memory Presets
  Press any number and the desk will return to the programmed height. See Programing Memory Presets to program presets.

• Arrow Keys
  Press and hold the UP arrow for the desk to begin raising. Release when desk reaches desired height. Press and hold DOWN arrow to lower desk. Release button when desired height is reached.

• Memory Mode
  To save a set height, press and hold the “1” button for 5 seconds until “H1” appears. Your height setting is now stored. Follow steps for the other numerical buttons to save up to four height settings.

• Reset Mode
  If the height of the desk is incorrect, press the down arrow until the desk moves to the fully lowered position. Press and hold the down arrow. “RES” will be displayed and the leg will lower and rebound upwards. Release the down arrow and your frame has been reset.

Troubleshooting

• E10
  Sensorless Alarm: This alarm triggered when the sensor cannot be detected. Power off desk and check the connection between the motor and control panel, then re-power.

• E20
  Overload Alarm: Remove desk items and try again.

• E02
  Rebound Protection: Check for desk vibration, obstacles, or desk incline. If no issues found, complete the reset process and try again.

• E32
  Overvoltage Alarm: Voltage is higher than allowed value. Power off desk and check connection between power and control panel. Power on again.

• E31
  Undervoltage Alarm: Voltage is lower than required value. Power off desk and check connection between power and contorl panel. Power on again.

• HOT
  Overheated Alarm: Power off and wait 18 minutes before use again.

EXPLORE MORE AT VIVO-US.COM

We offer a wide array of home & office products to fit your needs. From height adjustable desks to monitor mounts to keyboard trays and more!

• SPEAKER MOUNTS & STANDS
  Whether you’re mounting a soundbar or surround sound system, we’ve got a mounting solution to fit your needs

• CABLE MANAGEMENT
  From single monitor mounts to hex mount, gromment or clamp-ons, we’ve got a mounting solution for your setup.

• MONITOR MOUNTS
  From single monitor mounts to hex mount, gromment or clamp-ons, we’ve got a mounting solution for your setup.

WHO WE ARE

VIVO is more than a brand of ergonomic office furniture. We are a team of creative and innovative indivuduals working together to offer high quality, affordable ergonomic solutions. We think and work outside of the box to serve you, our customer, to the best of our abilitiy.

Need Assistance?

We Would Love to Help!

Personable Customer Support | Mon-Fri 7am-7pm
We offer immediate assistance with rapid response times from customer service agents and product techncians to help you every step of the way!

• Call Us: 309-278-5303
  • Average Resolution Time: 5m 4s
• Chat Us: www.vivo-us.com
  • Average Resolution Time: < 15m
• Email Us: help@vivo-us.com
  • Average Resolution Time: 1HR 8M
  • 23% within < 15m
  • 38% within < 30m
  • 61% within < 1hr
  • 83% within <2hr
  • 92% within < 3hr

FOR MORE GREAT VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: WWW.VIVO- US.COM

• VIVO-us
• @vivo_us

References

• Register a .US.COM domain today!
• VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
• Corner Electric Desk – VIVO - desk solutions, screen mounting, and more
• VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>