HEINNER HWM-M7012SMD++ Automatic Washing Machine Instruction Manual

HEINNER HWM-M7012SMD++ Automatic Washing Machine Instruction Manual

1. INTRODUCTION

Please read the instructions carefully and keep the manual for future information.
This manual is designed to give all necessary instructions concerning installation, use and maintenance of the unit. In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and use.

2. CONTENT OF YOUR PACKAGE

Automatic washing machine User manual Warranty certificate PACHET
ULUI DUMNEAVOAST

3. CONTENT OF YOUR PACKAGE

GENERAL
Please read the following safety information thoroughly and follow it strictly to minimize the risk of fire or explosion, electric shock and to prevent property damage, personal injury or loss of life. Failing to follow these instructions shall void any warranty.

• The appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision.
• Children should be supervised so that they do not play with the appliance.
• Children 3 years and under shall be kept away from the appliance or continuously supervised.
• Animals and children may climb into the machine. Check the machine before every operation.
• Do not climb or sit on the appliance
• All washing and additional substances are to be kept in a safe place out of the reach of children.
• Do not install the machine on a carpet floor. The obstruction of the openings by a carpet can damage the machine.
• Keep the appliance clear from heating sources and direct sunlight to avoid plastic and rubber parts corroding.
• Do not use the appliance in humid environments or rooms containing explosive or caustic gas. In case of water leakage or water splashes let the appliance dry in the open air.
• The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the washing machine.
• Do not operate the machine in rooms with a temperature of below 5°C. This can cause damage to parts of it. If it is unavoidable, make sure to drain the water completely from the appliance after every use to avoid damages caused by frost.
• Never use flammable sprays or substances in the immediate proximity of the appliance.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• If the machine is damaged, it must not be operated unless repaired by the manufacturer, its service agent or similarly qualified persons. Risk of electric shock!

INSTALATION

• Remove all packaging material and transport bolts before using the appliance. Otherwise, serious damage may result.
• This appliance is equipped with a single inlet valve and can be connected to the cold-water supply only.
• Mains plug must be accessible after installation.
• Before washing clothes for the first time, the product shall be operated once throughout all the procedures without any clothes inside.
• Before using the washing machine, the product shall be calibrated. ·Do not put any excessively heavy objects on the appliance, like water containers or heating devices.
• The new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused.
• Max. Inlet water pressure 1 MPa. Min. inlet water pressure 0.1MPa.

ELECTRICAL CONNECTION

• Make sure the supply cable is not trapped by the machine, it can get damaged.
• Connect the product to a grounded outlet protected by a fuse complying with the values in the “Technical specifications “table. The grounding installation has to be done by a qualified electrician. Ensure that the machine is installed in accordance with the local regulations. WARNING! ·Don´t use multiple plugs or extension cords. ·The appliance must not have an external switching device such as a timer or connected to a circuit that is regularly switched on and off. ·Do not pull the plug out of the mains outlet if there is flammable gas around. ·Never pull out the power plug with wet hands. ·Always pull at the plug, not at the cable. ·Always unplug the appliance if it is not being used.

WATER CONNECTIONS

• Check the connections of the water inlet tubes, the water taps and the outlet hose for possible problems due to changes of water pressure. If the connections loosen or leak close the water tap and get it repaired. Do not use the appliance before the pipes and hoses are installed properly by qualified people.
• Glass door may become very hot during the operation. Keep children and pets far away from the machine while it is operating.
• The water inlet and outlet hoses have to be safely installed and remain undamaged. Otherwise, water leakage can occur.
• Do not remove the drain pump filter while there is still water in the appliance. Big quantities of water can leak out, and there is a risk of scalding due to hot water.

OPERATION AND MAINTENANCE

• Never use any flammable, explosive or toxic solvents. Do not use gasoline and alcohol etc. as detergents. Only select detergents that are suitable for machine washing.
• Make sure that all pockets are emptied. Sharp and rigid items such as coins, brooches, nails, screws, stones etc. may cause serious damage to this machine.
• Remove all objects from pockets such as lighters and matches before using the appliance.
• Thoroughly rinse items that have been washed by hand.
• Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, wax and wax removers should be washed in heat with an extra amount of detergent before being dried in the appliance.
• Items containing foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the machine
• Fabric softeners or similar products should be used as recommended in their instructions.
• Never try to open the door forcefully. The door will unlock shortly after the end of a cycle.
• Please do not close the door with excessive force. If it is found difficult to close the door, please check if the clothes are properly inserted and distributed.
• Always unplug the appliance and close the water tap before cleaning and maintenance and after each use.
• Never pour water over the appliance for cleaning purposes. Risk of electric shock!
• Repairs shall only be carried out by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. The producer will not be responsible for damage caused by the intervention of non-authorized persons.

TRANSPORT

• Before Transport:
  -Bolts shall be reinstalled to the machine by a specialized person ­Accumulated water shall be drained out of the machine.
• This appliance is heavy.
• Transport with care.
• Never hold any protruding part of the machine when lifting.
• The machine door cannot be used as a handle.

INTENDED USE
The product is intended only for home use and for textiles in household amounts suitable for machine washing and drying. This appliance is for indoor use only and not intended for built in use. Only use according to these instructions. The appliance is not intended for commercial use. Any other use is considered improper use. The producer is not responsible for any damage or injuries that may result of it. ·This appliance is intended to be used in household and similar applications such as: -Staff kitchen areas in shops, offices and other working environments. -Farm houses. -By clients in hotels, motels and other residential type environments. -Bed and breakfast type environments. -Areas for communal use in blocks of flats or in launderettes.

4. PRODUCT DESCRIPTION

5. CONTROL PANEL

6. INSTALLATION

Installation area

• Stability is important to prevent the product from wandering!
• Make sure that the product should not stand on the power cord.
• Before installing the machine, the location characterized as follows shall be selected:

1. Rigid, dry, and level surface
2. Avoid direct sunlight
3. Sufficient ventilation
4. Room temperature is above 0
5. Keep far away from the heat resources such as coal or gas.

Unpacking the washing machine

• Packaging material (e.g. Films, Styrofoam) can be dangerous for children.
• There is a risk of suffocation!
• Keep all packaging well away from children.

1. Remove the cardboard box and Styrofoam packing.
2. Lift the washing machine and remove the base packing. Make sure the small triangle foam is removed with the bottom one together. If not, lay the unit down with side surface, then remove the small foam from the unit bottom manually.
3. Remove the tape securing the power supply cord and drain hose.
4. Remove the inlet hose from the drum. Make sure the small triangle.

Remove transport bolts.

• You must remove the transport bolts from the backside before using the product.
• You’ll need the transport belts again if you move the, so make sure keep them in a safe place.
  Please take the following steps to remove the bolts:

1. Loosen 4 bolts with spanner and then remove them.
2. Stop the holes with transport hole plugs.
3. Keep the transport bolts properly for future use.

Levelling the washing machine

• The lock nuts on all four feet must be screwed tightly against the housing

1. Loosen the lock nut.
2. Turn your foot until it reaches the floor.
3. Adjust the legs and lock the nuts with a spanner. Make sure the machine is level and steady.

Connect the water supply hose!
To prevent leakage or water damage, follow the instructions.

• Do not kink, crush or modify water inlet hose.
• Connect manually, do not use tools. Check if the connections are tight.

Drain Hose

• Position drain hose properly, otherwise damage might result of water leakage. ·Do not kink or protract the drain hose There are two ways to place the end of drain hose:
• If the machine has drain hose support, please install it like the following.

• When installing drain hose, fix it properly with a rope
• If the drain hose is too long, do not force it into washing machine as it will cause abnormal noises.

7. OPERATION

• Before washing, please make sure the washing machine is installed properly.
• Your appliance was thoroughly checked before it left the factory. To remove any residual water and to neutralize potential odors, it’s recommended to clean your appliance before first use. For this reason, start the Cotton program at 60°C without laundry and detergent.

Before washing.

• Detergent needs to be added in “case I “after selecting pre-washing for machines with this function.

• Make sure that the drum flaps are properly locked.

• All metal hooks must be properly hooked inside the rear door flap.

• Check the roller before each laundry, it must roll smoothly.

Washing and after washing

Before Each Washing

• The ambient temperature of the washing machine should be 5-40°C. If used under 0°C, the inlet valve and draining system may be damaged. If the machine is installed under freezing conditions, it should be transferred to normal ambient temperature to ensure the water supply hose and drain hose can unfreeze before use.
• Please check your laundry care labels and the detergent use instructions before washing. Use nonfoaming or less-foaming detergent suitable for machine washing properly.

• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances like wax, oil, paint, gasoline, alcohol, kerosene, and other flammable materials.
• Washing single clothes items may easily create big eccentricity and cause alarm due to unbalance. Therefore, it is suggested to add one or two more laundry items to the wash so that spin can be done smoothly.

Detergent Dispenser

Detergent Recommendation

• Agglomerating or ropy detergent or additive can be diluted in some water before pouring it into the detergent dispenser, to avoid its inlet getting blocked and thus cause a water overflow.
• Please choose the suitable type of detergent to get a maximum of washing performance and a minimum of water and energy consumption
• To achieve the best cleaning result a proper detergent dosing is important.
• Use a reduced detergent amount if the drum is not filled completely.
• Always adjust the amount of detergent to the water hardness, if your tap water is soft, use less detergent.
• Dose according to how dirty your laundry is, less dirty clothes require less detergent.
• Highly concentrated (compact detergent) requires particularly accurate dosing. Following symptoms are a sign of detergent overdosing:
  – heavy foam formation
  – poor washing and rinsing result Following symptoms are a sign of detergent underdoing:
  – laundry turns grey
  – built-up of limescale deposits on the drum, the heating element and/or the laundry

8. MAINTENANCE

Cleaning and Care

· Before your maintenance starts, please unplug the machine and close the tap.

Cleaning The Cabinet

• Proper maintenance on the washing machine can extend its working life.
• The surface can be cleaned with diluted non-abrasive neutral detergents when necessary.
• If there is any water overflow, use the wet cloth to wipe it off immediately.
• No sharp items are allowed.
• Formic acid and its diluted solvents or equivalent are forbidden, such as solvents or chemical products, etc.

Cleaning the drum

• The rusts left inside the drum by the metal articles shall be removed immediately with chlorine-free detergents.
• Never use steel wool.
• Don’t put laundry in the washing machine during the drum cleaning.

Cleaning the Inlet Filter

• Diminishing water flow is a sign that the filter needs to be cleaned.

1. Close the tap and remove the water supply hose from it.
2. Clean the filter with a brush.
3. Unscrew the water supply hose from the backside of the machine. Pull out the filter with long nose pliers.
4. Use a brush to clean the filter.
5. Reinstall the filter to the water inlet and reconnect the water supply hose.
6. Clean the Inlet filter every 3 months to ensure the normal operation of the appliance.

Clean The Detergent Dispenser

1. Press down the arrow location on softener cover inside the dispenser drawer.
2. Lift the clip up and take out softener cover and wash all grooves with water.
3. Restore the softener cover and push the drawer into position.

• Do not use abrasive or caustic agents to clean plastic parts.
• Clean the detergent dispenser every 3 months to ensure the normal operation of the appliance.

Cleaning the Drain Pump Filter

• Make sure that the machine has finished the washing cycle and is empty. Switch it off and unplug it before cleaning the drain pump filter.
• Be careful of hot water. Allow the water to cool down. Risk of scalding!
• Clean the filter periodically every 3 months to ensure the normal operation of the appliance.

9. TROUBLESHOOTING

The start of the appliance does not work, or it stops during operation. First try to find a solution to the problem, If not, contact the service center.

• After the check, activate the appliance. If the problem occurs or the display shows other alarm codes again, contact the service.

IMPORTANT STEPS WHEN MOVING THE APPLIANCE

• Check if the door and the detergent dispenser are closed properly.
• Remove the water inlet pipe and the outlet hose from the house installations.
• Let the water drain completely from the appliance
• Important: Re-install the 4 transport bolts in the back of the appliance.
• This appliance is heavy. Transport with care. Never hold any protruding part of the machine when lifting. The machine door cannot be used as a handle.

TECHNICAL DATA
The technical information is situated in the rating plate on the internal side of the appliance and on the energy label. The QR code on the energy label supplied with the appliance provides a web link to the information related to the performance of the appliance in the EU EPREL database. Keep the energy label for reference together with the user manual and all other documents provided with this appliance. It is also possible to find the same information in EPREL using the link https:// eprel.ec.europa.eu and the model name and product number that you find on the rating plate of the appliance. To access information about your product in the EPREL portal, you can scan the codes below:

Thank you for purchasing this product. If you need support with your product, visit our website using the links below. Get User manuals: https://www.heinner.ro
Get Service information: https://www.heinner.ro

www.heinner.com,
http://www.nod.ro

www.heinner.com
www.nod.ro

References

• Heinner – large appliances, small appliances, housekeeping, DIY
• Heinner – large appliances, small appliances, housekeeping, DIY
• NOD - Network One Distribution
• NOD - Network One Distribution
• Heinner – electrocasnice mari, electrocasnice mici, menaj, bricolaj

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>