HEINNER HBL-ICE1000XMC Stand Blender Instruction Manual
- June 9, 2024
- HEINNER
Table of Contents
HEINNER HBL-ICE1000XMC Stand Blender
INTRODUCTION
Please read this instruction manual carefully before using it and keep it
for later information
This manual is conceived for offering you all of the necessary info regarding
installation, using and maintenance of the machine. For a correct and safe use
of the machine, please, read this manual before installation and using.
PACKAGE CONTENTS
- Stand blender
- Instruction Manual
- Warranty card
SAFETY MEASURES
When using the electrical appliance, the below basic safety precautions should be followed:
- Read all instructions.
- Before using check that the voltage power corresponds to the one shown on the appliance nameplate.
- Do not let cord hang over edge of table or counter.
- Do not place on or near a hot gas or electric burner, or in a heated oven.
- Do not operate any appliance with a damage cord or plug or after the appliance malfunction or has been damaged in any manner. Return the appliance to the nearest authorized service facility for examination, repair or adjustment.
- If the supply cord is damaged， it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
- Close supervision is necessary when any appliance is used by or near children.
- Avoid contacting moving parts.
- Blades are sharp, so handle carefully.
- The use of attachment, including jar, jar lid, not recommended or sold by manufacturer may cause fire, electric shock or injury.
- The appliance can not be used for blending hard and dry substance, otherwise the blade could be blunted.
- Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning.
- To protect against risk of electrical shock do not put motor unit or power cord in water or other liquid.
- Do not use outdoors.
- Keep hands and utensils out of container while blending to reduce the risk of severe injury to persons or damage to the blender. A scraper may be used but must be used only when the blender is not running.
- To reduce the risk of injury, never place cutter-assembly blades on base without jar properly attached.
- Always operate blender with cover in place.
- This appliance can be used by children aged from 8 years and above and persons
- Always operate blender with cover in place.
- This appliance can be used by children aged from 8 years and above and persons
- Children should be supervised to ensure that they do not play with the appliance.
- Warning: never use hot liquids or run the appliance empty.
- Save this instruction.
PRODUCT DESCRIPTION
USING THE APPLIANCE
-
Unpack the appliance and place all parts on a horizontal surface.
-
Immerse the jar, jar lid and measuring cup in warm soapy water and rinse them and dry. Never immerse motor unit in water for cleaning to prevent the risk of electric shock.
Caution: The blade is very sharp, please handle carefully. -
The correct assembly way will be described in detail in below sections. Before assembling the jar, be sure the power cord is unplugged from the power outlet and the speed selector is on the OFF position. The blender jar is suitable for making mixture which the juice and pulp are mixed. For attaching jar, firstly place the jar lid into the jar, ensure the jar lid is placed tightly and properly with the jar. And then place the jar into the motor unit properly.
Note: Make sure all the assembly is placed properly.
BLENDING FRUIT AND VEGETABLE
-
Before assemble or attach the power cord into the outlet, make sure the speed selector is in OFF position.
-
Peel or core the fruit or vegetables and then cut it into small dices, put the food pieces into the jar. Usually certain amount of purified water should be added to facilitate the smooth running of appliance. The proportion of the food and water is 2:3. The amount of mixture should not exceed the max level as indicated on the jar.
Note: Never use boiling liquids or run the appliance empty. -
Place the jar lid in position tightly. Connect the plug to the wall outlet and turn the speed selector to ON position.
-
Turn the speed selector to adjust the speed. The speed selector is a stepless speed knob, the speed is gradually increased by turning clockwise.
-
You may add ingredients into the jar through the center opening of jar lid during operation, and then replace measuring cup if necessary. You just need to press down the measuring cup directly to fix it tightly.
-
The max operation time per time shall not exceed 3 minutes. Minimum 3 minutes’ rest time must be maintained between continuous two cycles.
-
Turn the Speed control knob to OFF position once the mixture has been blended to your desired consistency.
-
Remove the jar from the motor unit, carefully take off the jar lid, then pour and serve.
FUNCTION BUTTONS
When the speed selector is in ON position, you can use the following three
function buttons:
Pulse button: you can press and hold it if you want to accelerate the
process of blending.
Ice crush button: if there is ice in your ingredient, you can press it to
process food. The unit will operate at MAX speed and stop automatically after
finishing.
Blend button: after you pressing it, the unit will operate at MAX speed
for 60s, then stop automatically.
CLEANING AND MAINTENANCE
The Auto Clean feature can clean the blender and blade assembly easily and rapidly in complete safety.
- After use, reassemble the jar and pour a little warm water into it and turn the speed selector to Pulse position for a few seconds to remove the residual food.
- After stop, remove the jar from the motor unit and rinse the jar under running water.
- Wiping the outer surface of motor unit with a damp cloth, do not use abrasive cleansers.
- Never immerse in water or other solution for cleaning.
- Dry all parts and then replace them.
Warning: Do not use abrasive cleansers. Never immerse in water for cleaning.
Note: The blade is very sharp, handle carefully when clean.
TECHNICAL FICHE
- Rated voltage 220-240 V
- Rated frequency 50/60Hz
- Power 1000W
Environment-friendly disposal
You can help protect the environment!
Please remember to respect the local regulations: hand in the non-working
electrical equipment’s to an appropriate waste disposal center.
HEINNER is a registered trademark of Network One Distribution SRL. Other
brands and product names are trademarks or registered trademarks of their
respective holders.
No part of the specifications may be reproduced in any form or by any means or
used to make any derivative such as translation, transformation, or adaptation
without permission from NETWORK ONE DISTRIBUTION.
Copyright © 2013 Network One Distibution. All rights reserved.
This product is in conformity with norms and standards of European Community
Importer: Network One Distribution
Marcel Iancu Street, no 3-5, Bucharest, Romania
Tel: +40 21 211 18 56,
www.heinner.com
www.nod.ro
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>