Continental ACCM Access and Connected Car Module Installation Guide

Access and Connected Car Module (ACCM) &
Access and Connected Car Module PLUS (ACCM+)

INSTALLATION GUIDE (June 2021)

INTRODUCTION

Continental is a virtual key enabler. the Car & Connected Car Module – ACCM and the Car & Connected Car Module PLUS ­ ACCM+ allow vehicle access, authorization to start and vehicle data for any vehicle fleet management type

Consumption in stand-by mode
Operating temperature
Dimensions
Weight
Data transmission| 12Vcc
< 8 mA
– 25°C ≈ + 55°C
131.6 x 61 x 37.6 mm
130g
Bluetooth and LTE (US version only)
1 Power cable (OBDII connector)| |

ANTENNA FREQUENCY AND MAX POWER

Communication protocols| Antenna| | Frequencies
(MHz)| Max Power
(dBm)| Max Power
(dBm)
---|---|---|---|---|---
BLE| | | | 2402 ~ 2480| 4.08
4G LTE| North
America| LARA-R203| band 2
(1900MHz)| UL| 1850 ~ 1910| 23
DL| 1930 ~ 1990
band 4
(1700MHz)| UL| 1710 ~ 1755
DL| 2110 ~ 2155
band12
(700MHz)| UL| 699 ~ 716
DL| 729 ~ 746
EMEA| LARA-R211| band 3
(1800MHz)| UL| 1710 ~ 1785
DL| 1805 ~ 1880
band 7
(2600MHz)| UL| 2500 ~ 2570
DL| 2620 ~ 2690
band 20
(800MHz)| UL| 832 ~ 862
DL| 791 ~ 821

For ACCM + only:

BEFORE YOU BEGIN

• We advise our customers to have the ACCM fitted by a professional.
• Never remove the cover of the ACCM or ACCM+.
• Before you install the individual components, check that the installation area has been selected in such a way that:
• The cable length is sufficient to connect later every element: power cable and antenna (if necessary)
• for a car equipped with a keyless start system, the location where you plan to install the ACCM must be within the reception area of the keyless system of the car. Use therefore the original key and place it at the chosen installation area and check immediately that the engine can be started.
• Do not install any component in the airbag deployment area.
• Do not install the ACCM or ACCM+ against a large metal surface in the car.
• Once the installation is completed, make sure that no cables are pinched or trapped.
• In case you would like to buy additional keys and have them programmed to the vehicle’s immobilizer system in the future, some manufacturers require that all original keys are present in the car to be able to get an additional key. It will be necessary that you participate in the coding of the new key with a virtual key being active and connected to the car to perform the actions required by the dealer.
• Continental is not responsible for the damage caused to the vehicle and/or accessories with are the results of a non-respect of the instructions of this manual.

WARNING
ContinentalS. Aanditsaffiliates should not be held liable to ward send-users for the third parties prejudice caused by is usage of the product. We advise our customers to have the ACCM fitted by a professional.

IMPORTANT REMARKS

• Placing the ACCM or ACCM+ under or next to any large metal surface or an airbag could affect the reception of the ACCM.
• With the keyless start system, the vehicle doors can be opened without need for the driver to physically push a button on the key fob to lock or unlock the doors. To start or to stop the engine, there is no need to insert a key in the barrel to turn on the ignition.
• Installation steps 1 and 2 (see below) must only be performed for cars not equipped with a keyless start system. If the car is equipped with a keyless system, go directly to step 3.

INSTALLATION STEPS:

Disconnect the battery of the car.

1. Disassemble the shroud for easy access to the vehicle’s ignition switch. Pull the steering wheel in your direction to its maximum.

2. Place the ring of the antenna around the vehicle’s ignition switch as shown below.
   Fix and tape the ring around the ignition, excess cable can be taped together but may not be turned around (one rotation maximum). When using the ring method for installing the ACCM or ACCM+ the ring MUST be taped in front of the factory receiver ring. It CAN NOT be on top of, or behind the factory receiver ring. See illustration above. The antenna cable must follow existing steering column cables to avoid rupture while closing the shroud or moving the steering wheel.
   Reassemble the shroud.

3. Connect now the ACCM to the OBDII connector in the car. The OBD port is generally located in the driver cabin, between the door and the steering column.

4. Place the NFC reader (optional) on the bottom left corner of the windscreen. Use the provided sticker and tape to fix the reader on the windscreen. Place the sticker on the windscreen and use the tape to fix the reader on the sticker. The white side of the reader must be faced to the car. For your convenience, you can also decide to place the reader on the top left corner of the windscreen.

5. Reconnect the vehicle battery.

6. Validate that the ACCM or ACCM+ has a power connection (LEDs on side). You are now ready to test the ACCM with a virtual key on a smartphone equipped with the Continental mobile application.

7. Fix the ACCM or ACCM+ behind the dashboard.

Manufactured by: AMOTECH
Address: 5BL-1LOT, 380, Namdongseo-ro, Namdong-gu, Incheon, Korea 21629

WARRANTY

The customer shall benefit from the legal warranty against latent defects as specified in sections 1641 to 1649 of the Belgian Civil Code if the latent defect exists at the time of delivery and if the latent defect makes the unit unfit for the use for which it was designed or substantially reduces its use. Latent defects must be notified by registered letter to Continental within one month from the time the customer discovers it or ought reasonably to have discovered it. If the customer is a consumer, Continental shall be liable to the customer for any non-conformity which exists at delivery and appears within two years thereof. Any non-conformity shall be notified by registered letter to Continental within one month from the time the customer discovers it.

DISCLAIMER

The information in this document is subject to change without notice and does not represent a commitment on the part of the vendor. No warranty or representation, either expressed or implied, is made with respect of quality, accuracy or fitness for any particular purpose of this document. Without written permission from Continental, any forms of reproduction, spreading, distribution are prohibited. Continental reserves the rights to modify or improve the product without any prior notification. In no event will the supplier be liable for direct, indirect or special, incidental or consequential damages arising out of the user or inability to use this product or documentation, even if advised of the possibility of such damages. This document contains materials protected by copyright.

BLUETOOTH

The Bluetooth® word mark and logos are owned by the Bluetooth® SIG, Inc. and any use of such marks by Continental is under license. Other trademarks and trade names are those of their respective owners.

CE

Hereby, Continental declares that this Car & Connected Car Module is compliant with essential requirements and other relevant provisions of directive 2014/53/EU. The ACCM can be operated in at least one Member State without infringing applicable requirements on the use of a radio spectrum

FCC (FEDERAL COMMUNICATIONS COMMISSION)

WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. The device complies with Part 15 of FCC’s rules. Operation is subject to the following two conditions:
(i) this device may not cause harmful interference and
(ii) this device must accept any interference received, including interference that may cause undesirable operation.

MANUAL REQUIREMENTS ACCORDING 15.19/RSS-GEN

This device complies with Part 15 of the FCC Rules [and with Industry Canada licence-exempt RSS standard(s)]. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

MANUAL REQUIREMENTS ACCORDING 15.21

Changes or modifications made to this equipment not expressly approved by Continental Automotive GnbH may void the FCC authorization to operate this equipment.

FCC RF EXPOSURE REQUIREMENTS

This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

CORRECT DISPOSAL OF THIS PRODUCT (WASTE ELECTRICAL AND ELECTRONICS

EQUIPMENT)

This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly.

COPYRIGHTS

Copyright © 2015 Continental. All rights reserved. No part of this manual may be reproduced or transmitted in any means or for any purpose without the express written content of Continental. All trademarks, product names appearing in this document are registered property of their respective owners.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>