RUNPOTEC GF3 Cable Puller 50 m with Digital Meter Instruction Manual
- June 12, 2024
- RUNPOTEC
Table of Contents
RUNPOTEC GF3 Cable Puller 50 m with Digital Meter Instruction Manual
Instruction
Scope of delivery
Introduction
RUNPOTEC appreciates your purchase of a GF3 – Glass Fiber Ø 3 mm. These instructions for use provide information on safe use of your GF – Glass Fiber Ø 3 mm. Read the instructions for use thoroughly before commissioning. If you have any questions about commissioning, assembly, safety and applications, or problems, please contact your dealer or RUNPOTEC. You will find our contact data on page 2.
Safety information
Read the safety information on www.runpotec.com before use. The GF3 – Glass Fiber Ø 3 mm is used exclusively for pushing into pipes Ø 10 – 50 mm and for pulling in cables and lines. No liability is accepted for any other use! Please note the information on the special glue (item no. 30050) at www.runpotec.com
GF3 description
- Ergonomic holding and carrying handle
- RG7 – Guiding head with kink protection incl. swivel
- Kink protection
- Automatic glide back protection / lever
- Display with integrated digital meter counter – m/ft
- Reset button / activate, reset and switch from m to ft
- Button to open the box
- Accessories-/ repair box
- Easy service access – open with a single screw
Scope of delivery
- A GF3 – Box incl. RG7 – guiding head with front thread
- B Accessory box with repair kit
- C Button battery CR 2032
- D 1 x Special glue 3 g
- E 1 x Ergonomic pulling grip
- F 1 x Cable pulling loop with RTG Ø 6 mm thread and Schutzkappe
- G 1 x Kink protection
- H 2 x Mounting wrench
- I 3 x Eyelet Ø 7 mm, RTG Ø 6 mm thread
- J 1 x Coupling joint for Ø 3 mm
- K 6 x Adhesive joint for Ø 3 mm
- L 1 x Starting head Ø 11 mm, RTG Ø 6 mm thread
- M 1 x Fiber glass rod Ø 3 mm with 2 x kink protection
Commissioning / meter counter
-
Activate the display (meter counter): Briefl y press the reset button 6 once.
-
Caution! Measurement only takes place when the display is activated (moving the fiberglass rod is not enough). The display is automatically switched off after one minute of inactivity. Info: No manual switch-off possible. Set the meter counter to 0: Briefly press the reset button 6 once.
-
Meter (m)/Feet (ft) switch: Hold down the reset button 6 for 4 seconds.
-
Battery symbol: When the symbol lights up in the display, the battery on the back of the accessory box C needs to be replaced. (button battery CR 2032). If no symbol appears in the display, the battery voltage is OK. Battery life is approximately 3 years with average use.
Measurement Accuracy: In order to ensure the correct functioning of the meter counter, the accessory box B must be firmly fixed in the GF3 box with the screw 9 . After installing the accessory box, briefly press the reset button 6 once. Check measuring wheel for contamination and wear!
Measured value display – meters (m) / feet (ft):
- 0 – 99.99 m/ft 2 decimal places after the point
- 100.0 – 999.9 m/ft 1 decimal place after the point
- Negative measured value possible (minus in front of the value)
Easy and quick service access
On the back of the GF3 box, loosen the screw 9 in the middle to be able to
remove the accessory box B . After removing you have easy access to the
fiberglass rod 10 for repair or replacement or for changing the battery C on
the back of the accessory box.
Automatic glide back protection
Prevents the fi burgles rod with the guiding head incl. kink protection from slipping back into the GF3 box and thus always being at hand. Repair etc.: press the glide back protection 4 to the left to be able to push the fi burgles rod with the guiding head including kink protection into or out of the box.
Repairs
Repair of fiberglass rod with coupling joint (centre of rod)
-
Breaking situation
-
Saw off
-
Stripping Glue
Repair of fiberglass rod with adhesive joint and kink protection (bar beginning or bar end)
-
Breaking situation
-
Saw off
-
Gluing with adhesive joint A A 10min C = 12 mm
-
Fix the RG7 – guiding head with mounting wrench
-
Optional – calibrate
-
Fix eyelet
Technical information glass fiber rod
Rod| Rec. pipe Ø| Bending radius w. e. j| Bending radius rod| Breaking load|
Total breaking load
---|---|---|---|---|---
Ø| | | | |
3 mm| 10 – 50 mm| 38 mm| 28 mm| 450 kg| 130 kg
Application Cable pulling loop with RTG 6 thread
Attach cable
Application cable pulling loop
Accessories / combination products
integrated digital meter counter – ft/m
| GF3 Glass Fiber Ø 3 mm| Length| Item no.
---|---|---|---
with integrated digital meter counter – ft/m, 2 x kink protection on
fiberglass rod 16-piece accessories| 20 m 30 m 50 m| 10192 10193 10195
| GF3 Glass Fiber Ø 3 mm| Length| Item no
Ø 3 mm, incl. RG7 – Guiding head with front thread and eyelet Ø 7 mm incl.
swivel| 20 m 30 m 50 m| 10196 10197 10198
| Repairing-kit GF3 Ø 3 mm| |
Item no
15-parts, 1 x RG7 – Guiding head with front thread, 2 x Kink protection, 1 x
Special glue, 2 x Mounting wrench, 6 x Adhesive joint, 1 x Eyelet, 1 x
Coupling joint, 1 x Starting head| | 20819
| GF3 – RC2 – Special offer| |
Item no.
1 x GF3 Glass Fiber Ø 3 mm – cable pulling system – 30 m with integrated
digital meter counter – ft/m + 1 x RUNPOTEC inspection camera with 30 m cable
on a spool in the system case with extensive accessories| | 11146
RC2 inspektion-camera – areas of application with different RUNPOTEC cable pulling systems
GF3 – Glass Fiber Ø 3 mm
For small pipes from Ø 20 mm – 50 mm and up to a length of 50 meters
Fiber glass rod from Ø 4,5 mm RUNPOSTICKS
For waste water, ventilation pipes etc. from Ø 40 mm – 300 mm, protection rating IP 67
For shafts, underfill oar ducting, cavity wall, suspended ceilings, ventilation inspection and servicing, etc.
RUNPOTEC PRODUCTS
Profi cable pulling system RUNPO 5 – Ø 5,3 mm
For cable – Ø from Ø 16 mm – 40 mm
Cable pulling system GF3 Glass fiber rod Ø 3 mm
Integrated digital meter counter – m/ft
Push rod set RUNPOSTICKS Ideal for suspended ceilings, cable ducts, cavity walls, etc…
Digital cable length measuring device RM 35 For cables, single wires, ropes, pipes mit Ø 2 mm to Ø 32 mm
Fiberglass rod GF4.5 / GF6 / GF7.5 / GF9 / GF11 / GF15 Incl. double run-out s system and meter counter.
Mechanical cable pulling tool RT 2008
The problem solver for low pipe cross section Ø 16 – 32 mm
Cable pulling grip RUNPO Z RTG 6 LOOP
For cable diameter Ø 4 mm – 100 mm
Cable pulling loop HOOK / GEWINDE
For protected pulling of ready-made cables including plugs
Profi cable roller XB 300 – X BOARD
Multifunction mandrel for cable bundles or individual wires For small- to mid-
sized cable drums
Profi cable roller XB 500 – X BOARD
For all cable drums, cable bundles and pipes up to 800 kg
Cable drum roller PRO 530 / PRO 670 pre-assembled, incl. support rollers load bearing capacity 215 kg
Roll-off rails AS 900
For heavy cable cable drums from Ø 450 mm – Ø 2000 mm to 1700 kg
Cable drum lifter RUNPOLIFTER 4500 Set For drums up to 4500 kg – Ø 1600 mm
Capstan winch CW 800 E For horizontal cable pulling up to 800 Kg
Polyester cable pulling rope incl. steel reel for horizontal cable pull
Cable guide roller CHAIN / SHAFT / 90 DEGREES To gently pull cables around corners
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>