trend T35A M Class Vacuum Extractor Instruction Manual

trend T35A M Class Vacuum Extractor

DESCRIPTION OF THE APPLIANCE

1. Dust and/or water container
2. Pivoting wheels
3. Hose inlet
4. ON/OFF switch
5. AUTO switch automatic simultaneous ignition switch for power tools (depending on the model)
6. Socket panel for connection to power tools (depending on the model)
7. Clasp to open the dust collection compartment
8. Lid
9. Handle
10. Air outlet grid
11. Power supply cable
12. Spline
13. Guides
    • (A). Single or double layer paper bag (B). Paper cartridge filter
    • (C). Filter in polyurethane foam (only for wet & dry models)
    • (D). Basket with safety float (only for wet & dry models)
    • (E). Outlet filter of motor cooling air (only for wet & dry models)
    • (F). Air outlet filter (according to different models)

ACCESSORIES PROVIDED

*(according to different models): optional (see Fig. 5)**

• A1 Hose complete with handle and connection
• B1 extension tubes in metal or plastic B metal telescopic tube
• C1 Crevice tool
• D1 Upholstery nozzle
• E1 Dual-purpose brush or multi-purpose brush with accessory for hard floors and water.

ASSEMBLY INSTRUCTION

• Before using the appliance always check that all the filters provided are in the correct position.
• Position the polyurethane filter around basket (D) (Fig. 7, position 1).
• Position cartridge filter (B) in its seat (Fig. 7, position 2-3).
• When using bag (A), make sure the bag’s flange is properly inserted into the appropriate grooves 13 in the dust and/or water container (Fig. 7, position 4).

• Insert the bayonet cap at the end of the flexible hose into the inlet 3 and turn clockwise until locked as shown in Fig. 2.
• Join the extension tubes together or adjust the length of the telescopic tube by using the release button, and then connect the tubes or tube to the handle on the hose applying light pressure.
• To the other end attach a suitable accessory: Fig. 5:
• The dual-purpose brush cleans hard floors, carpets, and textile surfaces. To extract or remove the bristle strip push the button on the brush.
• The multi-purpose brush provided is suitable for cleaning carpets and textile surfaces.
• To clean hard surfaces and for vacuuming water it is necessary to attach the provided insert into the brush head.
• To fit the inserts, gently push the accessory into the main brush head until the hooks click into the side slots on the brush head as shown in Fig. 3.
• All the accessories provided can be attached to the end of the tubes or directly to the handle.

INTENDED USE

• This machine is intended for the collection, extracting, conveying, and separation of nonflammable dry specks of dust non-flammable liquids, and water-air mixtures.
• This M-class dust extractor is for professional use and is suited for trades and workshops.
• According to IEC/EN 60335-2-69, the vacuum of dust category M may only be used for vacuuming and extraction of hazardous dust with an exposition limit value;,: O, 1 mg/m3•
• This appliance is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops, offices, and rental businesses.
• The appliance is intended for use as a wet and dry dust extractor.
• Failure to comply with the abovementioned conditions will lead to cancellation of the guarantee.

Restriction of use

• DO NOT use the dust extractor for combustible dust.
• DO NOT use the dust extractor in explosive atmospheres.

SYMBOLS

• CAUTION! It is important to be careful on safety grounds.
• IMPORTANT
• LOCKED
• OPEN
• Optional
  IF PRESENT
  Double insulated (IF PRESENT): supplementary insulation is applied to the basic insulation to protect against electric shock in the event of failure of the basic insulation.

Additional Symbols Used

Wear Personal Protective Equipment (PPE). Ear, eye, and respiratory protection must be worn.

WARNING:
This appliance contains harmful dust. The emptying and maintenance, including the removal of the collection bag, may only be executed by trained personnel wearing suitable protection equipment. Do not switch on until the complete filter system has been installed. Otherwise, there is danger to your health. M Class dust extractors are suitable to vacuum dry, non-combustible dust with workplace limit values of ≥2 0, I mg/m3.

SAFETY

GENERAL WARNING

• Components used in packaging (if plastic bags) can be dangerous to keep away from children and animals.
• Operators shall be adequately instructed on the use of these machines.
• The use of this machine for anything not specified in this manual may be dangerous and must be avoided.
• Only use the socket outlet on the appliance for purposes specified in the instruction manual. (note: this is only for appliances provided with socket outlets).
• Always check the appliance before use.
• The suction nozzle should be kept away from the body, especially delicate areas such as the eyes, ears, and mouth.
• The appliance is not to be used by children or persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction.
• Children shall not play with the appliance.
• The equipment should be correctly assembled before use.
• Ensure that the power sockets used are correct for the machine.
• Never grasp the power cord with wet hands.
• Check that the voltage indicated on the rating plate is the same as the supply voltage.
• These machines are not suitable for vacuuming health-endangering dust or inflammable/explosive substances {like ash and soot).
• Never leave the equipment unattended whilst in use.
• Never carry out any maintenance on the machine without first disconnecting from the mains supply or when it is left unattended or reachable by children or disabled.
• The power cord should not be used to pull or lift the machine.
• The machine should never be immersed and never use a water jet against the appliance to clean it.
• When using the machine in wet rooms (e.g. in the bathroom) only connect it to sockets that are connected in series with a ground fault circu it interrupter. In case of doubt, consult an electrician.
• Periodically examine the power cord and machine for damage. If any damage is found, do not use the appliance but contact your service center for repair.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service centers, or similarly qualified people to avoid a hazard.
• If an extension cord is used, the plug and socket must be of watertight construction.
• Before vacuuming liquids, check the float functions correctly. When vacuuming liquids, and when the tank is full, a float closes the suction opening, and the vacuum operation is interrupted. Then switch off the machine, disconnect the plug, and empty the tank. Regularly clean the water level limiting device (float) and examine it for signs of damage.
• If the machine overturns, it would be recommended to stand it up before switching off.
• If foam or liquid escapes from the appliance, switch it off immediately.
• The equipment should not be used to vacuum water from containers lavatories, tubs, etc.
• Before emptying the tank, switch off the machine and disconnect the plug from the power outlet.
• Aggressive solvents or detergents should not be used.
• Service and repairs must be carried out by qualified personnel only. Only use the manufacturer’s original spare parts for service repair.
• The manufacturer cannot be held responsible for any damage/injury caused to persons, animals, or property caused by misuse of the appliance,
• Use only manufacturer-recommended attachments and manufacturer-original spare parts.

ADDITIONAL SAFETY RULES

WARNING:

• This appliance contains harmful dust. The emptying and maintenance, including the removal of the collection bag, may only be executed by trained personnel wearing suitable protection equipment. Do not switch on until the complete filter system has been installed. Otherwise, there is danger to your health.
• DO NOT pick up anything that is burning or smoking, such as hot ashes, matches, or cigarettes.
• DO NOT use to vacuum combustible explosive materials, such as grain, coal, or other finely divided combustible material.
• DO NOT use to vacuum hazardous, toxic, or carcinogenic materials, such as asbestos or pesticide.
• Never pick up explosive liquids (e.g. paint thinner, gasoline, diesel fuel, heating oil, etc.), acids, or solvents.
• DO NOT use the vacuum without filters in place, except as explained in the “Wet Vacuuming” section of this manual.
• Some woods contain preservatives which can be toxic.
• Take extra care to prevent inhalation and skin contact when working with these materials. Request and follow any safety information available from the supplier of the materials.
• DO NOT use a dust extractor as a seat, ladder, or stepladder.
• DO NOT place heavy objects on the dust extractor.
• DO NOT hang the dust extractor eg for transporting purposes.
• Wear Personal Protective Equipment (PPE). Ear, eye, and respiratory protection must be worn.

USE

The requirements for the ingress degree (dust category M) have only been proven for dry vacuuming.

• Be sure that the switch is in the off position (0) and connect the machine to a suitable socket.

DRY VACUUMING

• Class M vacuum cleaners are suitable to vacuum dry, non-combustible dust with workplace limit values of;, 0,1 mg/m3

Inserting the filters: (Fig. 7)

• (A) Paper bag.
• (B) Cartridge Filter.
• (C) Filter in polyurethane foam (only for wet & dry models)

WET-VACUUMING
For wet & dry models, before cleaning up liquids, make sure that the paper bag (A) and the cartridge filter (B) have been removed.

Inserting the filter: (Fig. 8)
(C) Filter in polyurethane foam (only for wet & dry models)

• The machine must be always kept on a horizontal basis, safely and stably.

• Insert the suitable filters for proper use.

• Never use the appliance without filters.

• Use the most suitable accessories for the requested usage.

• Put the switch on (-) ON position to start the machine.

• NOTE: An adequate ventilation rate (dust category class M) must be provided for when the outgoing air is circulated.

• WARNING:
  DO NOT connect power tools to outlet{when using the vacuum for wet pick up.

• NOTE: Plug dust extractor into residual current device (RCD) protected outlet when using it for wet pick up.

• When the job is over, switch off (0) OFF and keep away the plug from the socket.

BLOWER FUNCTION

CAUTION:
The function is not usable if the appliance is used to dry vacuum harmful dust.

The appliance can also be used as a blower:
Remove the air outlet grid 10 by pressing gently on the closure tab, remove the hose from inlet 3, and then insert the bayonet cap of the hose into the blower outlet situated inside the lid, behind the air outlet grid, as shown in Fig. 4.

• When the job is over, switch off (0) OFF and keep away the plug from the socket.

STARTUP

• (0) OFF, SWITCH OFF
• (I) ON, MANUALLY OPERATED: VACUUMING
• AUTOMATICALLY OPERATED WITH CONNECTING ELECTRIC POWER TOOL TO SOCKET – SOCKET FOR TOOLS MAX. 2300W

CONNECTING ELECTRIC POWER TOOLS Fig. 9:

WARNING:

• Observe the maximum connected loads for the appliance socket (Refer to the SPECIFICATIONS.)
• Make sure that both the cleaner and the electric power tool are switched off before connecting or disconnecting.
• To connect an electric power tool, open the cap and insert the power tool plug into the socket of the cleaner.
• Rotate the switch lever to the “AUTOMATICALLY” position.
• Switching ON and OFF of the connected electric power tool simultaneously brings the cleaner swi­tching on and off action.
• At the end of the cycle, the filter shake function will be activated for about six seconds.
• After use, disconnect the power tool from the socket of the cleaner.
• Switch off the cleaner after use.
• Even when rotating the switch to position (I) ON , the electric tool socket is live.

To clean the filter manually, set the selector/V to the symbol of the filter cartridge.

CARE AND MAINTENANCE

• The machine shall be disconnected from its power source, by removing the plug from the socket-outlet, during cleaning or maintenance.
• Clean the exterior part of the machine with a dry cloth.
• Move the appliance only by catching the carrying handle located on the motor head.
• Store the appliance and the accessories in a dry safe place, out of the reach of children.
• A dust-technical inspection is to be carried out at least once every year by the manufacturer or an instructed person, e.g. for damage to the filter, tightness against leakage of the dust extractor, and function of the control unit.
• For M-class dust extractors that were in contamina­ted environments, the exterior as well as all machine parts should be cleaned.
• When performing maintenance and repair work, all contaminated components that cannot be cleaned to satisfactory must be disposed of.
• Such components must be disposed of in imperme­able plastic bags conforming with the valid regulations for the disposal of such waste.

Filter cleaning

Changing the paper dust bag

REPLACEMENT OF FILTERS

• The machine shall be disconnected from its power source, by removing the plug from the socket-outlet, during cleaning or maintenance
• Once the filter has been cleaned, check whether it is suitable for further use. If it has been damaged or broken, replace it with an original filter.

For the cleaning and maintenance of the filters, follow these instructions:

The paper dust bag

• The paper dust bag must be replaced when the indicator light remains on.
• Close the bag by sliding the tab 12. It is good practice, however, to change the bag regularly to guarantee optimal cooling of the motor.
• Dispose of the filter in a suitable container according to the applicable laws.
• If the dust extractor is used without the paper dust bag, it is recommended that the dust container be emptied and cleaned after each use; this procedure is also recommended following the suction of any type of liquid.

The paper cartridge filter
It should periodically be washed only externally under running water to avoid damage to the filter surface. It is recommended, however, that this filter be replaced every six months, also about the frequency of use and to the type of dirt.

The polyurethane foam filter
Must be cleaned regularly by brushing and/or by wa­shing with water and neutral detergent. It is also recommended that this filter be replaced regularly, depending on the frequency of use and type of dirt.

Air outlet filters
Filter for motor cooling air, only for wet & dry models. Various types {depending on the model) of air outlet filters for all versions. These filters must be replaced regularly with new filters at least every six months, and in any case according to the type of dirt and frequency of use.

Careful cleaning, maintenance, and replacement of filters are essential to guarantee:

• Maximum efficiency of the appliance
• Reduction of dust returned to the environment
• Optimal cooling of the motor

GENUINE SPARES AND CONSUMABLES
Always replace parts with genuine spares. These are available from your local store dealer. When ordering parts always quote your model number.

After Sales Service
Should you require service at any time, please contact your local After Sales Service.

WARRANTY CONDITIONS

All our machines are subjected to strict tests and are covered against manufacturing defects under applicable regulations. The warranty is effective from the date of purchase.

The following are not included in the warranty:

• Parts are subject to normal wear.
• Rubber parts, charcoal, filters and the accessories and optional accessories.
• Accidental damage caused by transport, neglect or inadequate treatment, incorrect or improper use, and installation failing
• The warranty shall not cover any cleaning operations to which the operative components may be subjected, such as clogged nozzles and filter blocked due to limestones.

DISPOSAL (WEEE)
As the owner of electrical or electronic equipment, the law (per the EU Directive 2012/19/EU) prohibits you from disposing of this product or its electrical/electronic accessories as municipal solid waste and obliges you to make use of the appropriate waste collection facilities. The product can be disposed of by returning it to the distributor when a new product is purchased. The new product must be equivalent to that being disposed of.

DECLARATION OF CONFORMITY

UK DECLARATION OF CONFORMITY

The undersigned, representing the following manufacturer

Manufacturer:
Trend Tool Technology Ltd, Watford, England WD24? TR declares that the product(s):

Product Identification:

• Product: Vacuum Cleaner
• Brand: Trend
• Model: T35A

Conforms to the following UK Regulations

• The Supply of Machinery (Safety) Regulations, 2008, S. I. 2008/1597 (as amended).
• Electromagnetic Compatibility Regulations, 2016, S.I. 2016/1901 (as amended).
• The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012, S.I. 2012/3032 (as amended). and the following Designated Standards:
• S.I. 2008/1597:
  • EN 60335-1
  • EN 60335-2-69
  • EN 62233:2008+AC:2008
• S.I. 2016/1091: EN 55014-1:2006+A 1:2009+A2:2011
  • EN 55014-1:2017 +A 11:2020
  • EN 55014-2:2015
  • EN 55014-2:1997+AC:1997+A1:2001 +A2:2008
  • EN 61000-3-2:2014
  • EN 61000-3-3:2013
• S.I. 2012/3023: IEC EN 63000:2018

The undersigned is responsible for the compilation of the technical file and makes this declaration on behalf of Trend Tool Technology Ltd.

Neil McMillan
Technical Director

Trend Tool Technology Ltd,
Odhams Trading Estate,
Watford, WD24? TR,
England
01/08/2021

EU – Declaration of Conformity

Vacuum Cleaner Product Ref.
We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and conform with the following standards.

Technical file at:

• Trend Tool Technology Ltd. Watford, WD24 7TR, England
• Tel: 0044(0)1923 249911
• technical@trendm.co.uk
• www.trend-uk.com

EU Importer:
Trend Tool Technology Ltd. 3rd Floor, Kilmore House, Park Lane, Spencer Dock, Dublin 1, Ireland

• © Trend Tool Technology Ltd. 2022.
• ® All trademarks acknowledged E&OE

No part of this publication may be reproduced, stored, or transmitted in any form without prior permission. Our policy of continuous improvement means that specifications may change without notice. Trend Tool Technology Ltd, cannot be held liable for any material rendered unusable, or for any form of consequential loss. E&OE.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>