GUANGDONG MW14S-E1 Wifi Bluetooth Module User Manual

GUANGDONG MW14S-E1 Wifi Bluetooth Module

The product description

The user can achieve the terminal equipment connection WIFI net and Bluetooth, through this module.
This equipment may be operated in all European countries.

Interface

• Interface
  16pin stamp hole
  

• Pin definition
  PIN| Name| Function| Remark
  ---|---|---|---
  PIN1| GND| GND| GND
  PIN2| VCC| VCC| 3.3V
  PIN3| NC| |
  PIN4| RX Log| RX Log| Download and capture log
  PIN5| TX Log| TX Log| Download and capture log
  PIN6| TX| TX| TLL level
  PIN7| RX| RX| TLL level
  PIN8| GND| GND| GND
  PIN9| GND| GND| GND
  PIN10| GPIO_2| GPIO (Reserved)|
  PIN11| GPIO_1| GPIO (Reserved)|
  PIN12| RESET| Hardware Reset| Module Reset when pull down
  PIN13| NC| |
  PIN14| DL_MODE| Forced download| In download mode when pull up
  PIN15| NC| |
  PIN16| GND| GND| GND

• Power consumption requirements
  The maximum working current is not more than 500mA, the instantaneous maximum current is not more than 700mA; In standby mode, the power supply of the module shall be no less than 0.45W, and the power supply current shall be no less than 1A (DC-DC is recommended)

Basic parameters

Spread Spectrum)
IEEE 802.11g: BPSK, QPSK,16QAM,64QAM for OFDM (Orthogonal Frequency Division Multiplexing)
IEEE 802.11n: MCS0~MCS7,OFDM
Modulation Method| DSSS/DBPSK/DQPSK/16-QAM/ 64-QAM
Data Transfer Rate| 802.11b:1,2,5.5,11Mbps
802.11g:6,9,12,18,24,36,48,54Mbps
802.11n:MCS0~MCS7,up to72.2Mbps
Antenna Reference| PCB printed ANT
Interface| 16pin stamp hole
Supply Voltage| 3.3V±0.3V
Dimension| 20×18×3.2mm
Weight| 1.5g
Operating Temperature| -10°C to 70°C
Storage Temperature| -20°C to 85°C

Note:

Low Temperature Operation
When the external temperature is lower than -10°C, the modules have an increased risk of damage and face unpredictable risks. Do not use modules at temperatures lower than -10 °C!

The display method of Model approved code

In the factory, the model approve code is pasted on the back shell in a label.

CE Statement

EU DECLARATION OF CONFORMITY

Hisense declares that the radio equipment type Hisense MW14S is in compliance with Directive 2014/53/EU.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of FCC RF Rules.

This equipment should be installed and operated with minimum distance of 20 in (50cm)between the radiator and your body. This transmitter must not be co- located or operated in conjunction with any other antenna or transmitter.

CAUTION:

To comply with the limits of the Class B digital device pursuant to Part 15 of the FCC Rules, this device is compliant with Class B limits. All peripherals must be shielded and grounded. Operation with non-certified peripherals or non-shielded cables may results in interference to radio or reception.

MODIFICATION

To assure continued compliance, Any changes or modifications not expressly approved by the grantee of this device could void the users authority to operate the device.

Radiation Exposure Statement

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 50 cm(8 in )between the radiator and your body NOTE To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product Contains Transmitter module FCC ID: 2A4A3MW14S-E1

To satisfy IESD exterior labeling requirements, the following text must be placed on the exterior of the end product “Contains Transmitter module IC:

This symbol on the product or on its packaging indicates that this product must not be disposed of with your household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>