BLAUPUNKT BPS-E695 5 Way Car Speaker System Instruction Manual

BLAUPUNKT BPS-E695 5 Way Car Speaker System

Product Information

Specifications

• Model : BPS-E695 (E-Series) / BPS-X6950 (X-Series)
• Size : 6X9in (164*236mm)
• Impedance : 4ohm
• Power Handling : 70W RMS / 35W Peak
• Sensitivity : 85dB (E-Series) / 88.8dB (X-Series)
• Frequency Response : 45Hz – 20000Hz (E-Series) / 40Hz – 20000Hz (X-Series)
• Mounting Dimensions : 6.068.74in (154222mm)
• Mounting Depth : 1.2in (30mm) (E-Series) / 1.42in (36mm) (X-Series)
• Magnet Type : Neodymium (E-Series) / Neodymium (X-Series)
• Tweeter Type : PET Balanced Dome (E-Series) / PEI Balanced Dome (X-Series)
• Midrange Type : Ceramic w/PET Diaphragm Balanced Dome (E-Series) / Ceramic w/PEI Diaphragm Balanced Dome (X-Series)
• Woofer Type : Ferrite PET Balanced Dome (E-Series) / Ferrite PEI Balanced Dome Carbon Fiber Rubber (X-Series)

Product Usage Instructions

Wiring

• Blaupunkt Speaker wired to a single channel Total Impedance : 4 ohms x channel
• Altavoz Blaupunkt conectado a un solo canal. lmpedancia Total : 4 ohms x canal
• Blaupunkt Speakers wired in parallel to a single channel Total Impedance : 2 ohms x channel
• Altavoces Blaupunkt conectados en paralelo a un solo canal. lmpedancia Total : 2 ohms x canal

Mounting

NOTE: BLAUPUNKT strongly recommends that you operate your system at low volume levels prior to the complete installation of your BLAUPUNKT speakers.

CAUTION: Make sure that all of the speaker wiring is fully protected from cuts, tears or possible wear. Any short circuit caused from cuts, tears or wears, could severely damage the source unit or amplifier. Make sure all speaker wires easily reach the speaker terminals with no stress on the wires or connectors.

IMPORTANT: Never cut any metal that is an integral part of the vehicle’s safety or structural support system. If you are unsure of the importance of any components of your vehicle, it is recommended that you have your speaker professionally installed.

CHOOSING A LOCATION: It is always best to plan the complete installation prior to attempting to install any product. The routing of wires, power connections, and mounting location should be planned first. As with any car stereo installation, all work performance should be checked thoroughly and carefully prior to the operation of the system.

BLAUPUNKT Speakers are designed to fit in almost any factory location. If at all possible, it is recommended that you use  factory locations. This applies mostly to later model cars. For those earlier model cars that do not have factory location or are limited to just front speakers, it is recommended that you choose a location with a sufficient amount of air space.

If there’s not enough air space, the woofer of the speaker may not reproduce low frequencies very well. It is recommended to mount the speakers in the door panels, kick panels, rear deck, etc. Ideally, the speakers should be mounted where it will be in an enclosed airspace. This allows for an extended bass response.

FAQ

• Q: Can I wire the speakers in parallel to a single channel?
  A: Yes, Blaupunkt speakers can be wired in parallel to a single channel. The total impedance in this configuration will be 2 ohms x channel.

• Q: What is the recommended power handling for these speakers?
  A: The speakers have a power handling of 70W RMS / 35W Peak.

• Q: Where should I mount the speakers?
  A: BLAUPUNKT Speakers are designed to fit in almost any factory location. If possible, use factory locations. For earlier model cars without factory locations or limited to front speakers, choose a location with sufficient air space. Mounting the speakers in door panels, kick panels, or rear deck, ideally in an enclosed airspace, will provide extended bass response.

5 Way Car Speaker System

E-Series
BPS-E695
X-Series
BPS-X6950

BP Americas Corp
9590 NW 40th St Road Doral, FL 33178

WIRING
Blaupunkt Speaker wired to a single channel Total Impedance : 4 ohms x channel

Blaupunkt Speakers wired in parallel to a single channel Total Impedance : 2 ohms x channel

MOUNTING

• NOTE : BLAUPUNKT strongly recommends that you operate your system at low volume levels prior to the complete installation of your BLAUPUNKT speakers.

• CAUTION : Make sure that all of the speaker wiring is fully protected from cuts, tears or possible wear. Any short circuit caused from cuts, tears or wears, could severely damage the source unit
  or ampli?er. Make sure all speaker wires easily reach the speaker terminals with no stress on the wires or connectors.

• IMPORTANT : Never cut any metal that is an integral part of the vehicle’s safety or structural support system. If you are unsure of the importance of any components of your vehicle, it is recommended that you have your speaker professionally installed.

• CHOOSING A LOCATION : It is always best to plan the complete installation prior to attempting to install any product. The routing of wires, power connections, and mounting location, should be planned ?rst. As with any car stereo installation, all work performance should be checked thoroughly and carefully prior to the operation of the system.

• BLAUPUNKT Speakers are designed to ?t in almost any factory location. If at all possible, it is recommended that you use factory locations. This applies mostly to later model cars.
  For those earlier model cars, that do not have factory location or are limited to just front speakers, it is recommended that you choose a location with a sufficient amount of air space.

• If there’s not enough air space, the woofer of the speaker may not reproduce low frequencies very well. It is recommended to mount the speakers in the door panels, kick panels, rear deck, etc. Ideally, the speakers should be mounted where it will be in an enclosed airspace.

• This allows for an extended bass response.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>