Wi-Tek Alien Series 24-48V Smart PoE Switch Installation Guide
- June 15, 2024
- Wi-Tek
Table of Contents
Wi-Tek Alien Series 24-48V Smart PoE Switch
Packing Content
Appearance Overview
WI-PMS328GF-Alien
LED indicator
| LED Indicators | Description |
|---|---|
| PWR | On: the device power on is normal |
Off: the device is power off or failed
SYS| Blinking: device initialization
On: device on and normal operation
PoE| Solid on: PoE is working
Off: PoE not working
Link/Act| Blinking: Data transmission is active and working
On: PD connected to the PoE port, but no data transmission
1000M| On: The port negotiated rate is 1000 Mbps
Off: The port negotiated rate is not 1000 Mbps
25-28
(SFP Indicator)
| Blinking: data on TX/RX On: ports link up
Off: ports link down
WI-PMS310GF-Alien
LED indicator
| LED Indicators | Description |
|---|---|
| PWR | On: the device power on is normal |
Off: the device is powered off or failed
SYS| Blinking: device initialization
On: device on and normal operation
PoE| Solid on: PoE is working
Off: PoE not working
Link| Blinking: Data transmission is active and working
On: PD connected to the PoE port, but no data transmission
9, 10
(SFP Indicator)
| Blinking: data on TX/RX On: ports link up
Off: ports link down
WI-PS310GF-Alien
LED indicator
WI-PS310GF-Alien DIP Switch Description
Default| All ports free communication, suitable for common
data transmission environment
VLAN| The PoE ports are isolated from each other but can only communicate with
uplink ports, which can effectively restrain the broadcast storm and improve
the performance of a network
LED Indicators| Description
POWER| Solid on: The device power on is normal
Off: The device is power off or failed
PoE
PoE
| Green| Solid on: PoE is working with 48V power
Off: PoE not working
| Orange| Solid on: PoE is working with 24V power
Off: PoE not working
PoE
Link
| Green| Blinking: Data transmission is active and working
On: The port negotiated rate is 10/100 Mbps
| Orange| Blinking: Data transmission is active and working
On: The port negotiated rate is 100/1000 Mbps
9, 10
(SFP Indicator)
| Blinking: data on TX/RX On: ports link up
Off: ports link down
WI-PMS310GF-Alien-I
LED indicator
| LED Indicators | Description |
|---|---|
| PWR | On: the device power on is normal |
Off: the device is powered off or failed
V1/V2
(Input power indicator)
| On: Power is supplied via V1/V2 DC connector
Off: No power supply
PoE
| Green| Solid on: PoE is working with 48V power
Off: PoE not working
Orange| Solid on: PoE is working with 24V power
Off: PoE not working
PoE
Link
| Green| Blinking: Data transmission is active and working
On: The port negotiated rate is 10/100 Mbps
| Orange| Blinking: Data transmission is active and working
On: The port negotiated rate is 100/1000 Mbps
9, 10
(SFP Indicator)
| Blinking: data on TX/RX On: ports link up
Off: ports link down
Ring| On: The fast ring mode is enable
Off: The fast ring mode is disable
Giga| On: The port negotiated rate is 1000 Mbps
Installation
- Desktop installation (WI-PMS328GF-Alien、WI-PMS310GF-Alien、WI-PS310GF-Alien)
- Rack mounted (WI-PMS328GF-Alien)
DIN-rail Mount installation(WI-PMS310GF-Alien-I)
- Installing WI-PMS310GF-Alien-I, place the WI-PMS310GF-Alien-I in a desired location using the Din-rail fixtures.
Please install the WI-PMS310GF-Alien-I in a proper enclosure or shelter. The WI-PMS310GF-Alien-I must be grounded.
Login WEB UI
For more L2 management functions, please log in the Web-Based Ul as the following steps:
Step 1. Find the lP address of the switch.
- The default login lP address of this series switch is 192.168.0.1, with a subnet mask of 255.255.255.0.
- lf the switch receives an lP address from a DHCP server in your network. You can find this lP address on the DHCP server. Step 2. Configure the lP address on your PC to make sure the switch and PC are in the same subnet.
- lf the switch uses the static IP address of 192.168.0.1, configure your PC’s lP address as192.168.0.x (” x ” ranges from 2 to 254), and the subnet mask as 255.255.255.0.
- lf the switch uses an lP address assigned by a DHCP server, set your PC to obtain an IP address automatically from the DHCP server.
Step 3. Launch a web browser on your PC. Enter the lP address of the switch in the address bar and fill in the username and password.
- The default login username and password are both “admin”.
Warranty Card
-
Username
-
Address
-
Telephone No.
-
Purchase Shop
-
Purchase Address
-
Product Model No.
-
Purchase Time
-
Serial No.
-
Dealer Signature
- If the product is defective within three months after purchase, we will provide you a new product of the same model.
- If the product defects within the three-year warranty period, we will provide professional maintenance service.
- Proof of purchase and a complete product serial number are required to receive any services guaranteed as part of the limited warranty.
- Any other defects that are not caused by workmanship or product quality, such as natural disasters, water damage, extreme thermal or environmental conditions, sticker damage, warranty card loss will disqualify the product from limited warranty.
-
Wireless-Tek Technology Limited
-
Address: Biaofan Technology Building 402, Bao’an Street,
-
Baoan District, Shenzhen City, Guangdong, China
-
Website:www.wireless-tek.com
-
Tel:86-0755-32811290
-
Email:sales@wireless-tek.com
-
Technical Support:tech@wireless-tek.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>