Maisto 82241 Radio Control Vehicle Instruction Manual

Maisto 82241 Radio Control Vehicle

Please keep this owner’s instruction manual for future reference. It contains important information. We reserve the right improve/revise the product specifications without notice.

Contents:

• RC Vehicle With Built-in Rechargeable Battery (non replaceable) x 1
• Controller x 1
• USB Cable x 1
• 1.5V “AAA” LR03/R03 non-rechargeable Battery (For Controller Use) x 2
• Owner’s Instruction Manual x 1

Charging the built-In rechargeable battery for the RC vehicle: (Reier to Diagram 1)

1. Open the charging port cover on the vehicle.
2. Make sure the switch Is on the CHARGE position before charging.
3. Locate a USB certified port from any of the devices shown here,
4. Connect the USB charging plug with the USB-certified port.
5. The charge indicator will start twinkling in green to show it is charging.
6. Once the chargeLEDlndicator stays on the green, the battery is fully charged.
7. Detach the USB plug from the USB certified port, then install the charging port cover on the vehicle.

Battery Installation for the controller: (Reier to Diagram 2)

1. Switch the power OFF.
2. Use screw driver to loosen the screw on the battery cover and open the battery cover.(Screwdriver is not included)
3. Install 2 new 1.SV “MA” LAD3/R03 batteries with correct polarity (+/-)as shown inside the battery compartment.
4. Install the battery cover and then tighten the screw on the battery cover.

How to play: (Reier to Diagram 3, 4 & 5)

1. Set the ‘Power Switch’ on the controller and vehicle to ON position, the “Power LED” on both the controller and vehicle will flashlees than3secondsthen action,meaning the automatic frequency matching between the controller and the vehicle is completed.
2. If the ‘ Power LED’ of the controller or the ‘Power LED’ of the vehicle flash more than3 seconds, switch off both the vehicle and controller, then turn again.
3. The top LED will light in blue when the power of the vehicle is turned on.
4. Pull the trigger on the transmitter to drive the vehicle forward. Push the trigger
5. Pull or push the trigger on the transmitter and turn the steering wheelto control the vehicle turn to left or right.
6. Turn the steering wheel to left or right to control the vehicle spin360°.
7. Try different combinations of the trigger and steering wheel to perform different sideways drifting stunt actions.
8. The “PowerLED”on the vehicle will not flash nor stay on if the rechargeable battery has run outpower..
9. Turn the Switch of the controller and vehicle to off position what not in play.

Performance Tips:

1. Do not drive the vehicle on grass, sand or go through water.
2. Do not drive the vehicle in windy or rainy weather.
3. Do not drive the vehlcle into any hard object.
4. Keep fingers,hair and loose clothing away from the vehicle.
5. The operating range canbe affected by variety of factors·
6. Weakcontroller or vehicle batteries
7. Interference from other items that emit radio frequency signals such as another R/Citemon the same frequency, CB radios, cordless phones, high voltage transmitters. etc.
8. Outdoor usage is recommended in order to get optimal control range.
9. Remove the package, take out all accessories and assemble the product before giving it to children to play.

Cautions :

1. The Built-in rechargeable battery must be charged before use.
2. Do not overcharge the Battery. Do not charge for more than1.5 hours except for the initial two charges.
3. Do not charge the battery if it shows leakage, corrosion, or has loose or exposed wires or other damage
4. Do not cover the vehicle with any sort of material while charging.
5. Donot touchthe vehlcle when lt is hot. Wait untllthe vehlcle coolsbefore recharging.
6. Do not dispose of the Batteryinfire.
7. Do not dismantle the Battery or USB, and do not cut the Battery or USB cables.
8. The USB Cable used with the toy shall be regularly examined for damage to the cord, plug, enclosure, and otherparts, and in the event of such damage,they must not be used until the damage has been repaired.
9. Rechargeable batteries are to be removed from the toy before being charged(for transmitter).
10. The Battery will be warm after charging, and hot after use in a Vehicle.
11. The supply terminals are not to be short-circuited.
12. Rechargeable batteries are only to be charged by adults or by children atleast8yearsold.
13. Batterychangemust only is made by adults!
14. Note that the 1.5V ‘AAA’ Battery is non-rechargeable and is not to be recharged. Only Batteries of the same or equivalent type as recommended are to be used. It will need replacement when the transmission is poor. Alkaline AAA batteries are recommended to be used for the transmitter. Do not mix alkaline, standard or rechargeable batteries, Do not mix old and new batteriesor different type of batteries. Be sure to insert batteries with correct polarities and always follow the battery manufacturer’s instructions.
15. Exhausted batteries must be removed from the product.

FCC Label Compliance Statement:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions :

1. Thisdevicemaynot cause harmful interference,and

2. This device must accept any interference received, including interference that may cause undesired operation.
   Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and,ifnot installed and used in accordance with the instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a particular installation. this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
   off and on,the user is encouraged to try to correct the interference by one or more of the following measures:

   • Reorient or relocating the receiving antenna
   • increase the separation between the equipment and receiver.
   • Connectthe equipment into an outlet on a circuit different from that to which the receiver is connected.
   • Consult the dealer or an experienced radio/tv technician for help.
     Warning : Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Disposal of batteries

Batteries should not be disposed of in the household waste. As the consumer, you are legally obliged to return batteries containing harmful substances and all other used batteries
You can hand in your old batteries at public collection points in your area or wherever batteries are sold.
You will find these chemical abbreviations along with a crossed-out refuse battery containing harmful substances:

• Pb=Batterycontains lead
• Cd=Batterycontains cadmium
• Hg=Batterycontainsmercury

RSS-210 Compliance Statement:

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference;
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Malsto lntematlonal,lnc
Fontana,CA92336, U.S.A

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>