LEVITON SP4487 Retrofit Instruction Manual

LEVITON SP4487 Retrofit Instruction Manual

Installation Instruction Guide

Available in a wide range of configurations with standard sizes.
The retrofit kit is designed to retrofit Listed Recessed Fluorescent Troffer Luminaires of sizes 2×2, 2×4, 1×4 with minimum depth of 3.5”

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

NOTES

• Installation should be completed by an individual familiar with the construction and operation of the luminaire.
•  Installation of luminaire must be in accordance with national and local building and electrical codes.
•  Carefully read and follow all warnings and instructions before installing or servicing the luminaire.
•  Instructions do not cover all details and all possible product configurations
•  Do not restrict luminaire ventilation.
•  Ensure LED luminaire is not covered with material that will prevent convection or conduction cooling.
•  Do not exceed luminaire’s maximum ambient temperature.
•  Ensure LED luminaire has the correct polarity before installation.

These products have maximum rated output voltage that exceeds the voltage limits that cannot be accessible based on voltage restrictions for Class 2 circuits in Canadian Electrical Code. This output complies with the definition of Class 2 per Canadian Electrical Code. This product complies with this requirement since the installation instruction requires installation in restricted access area.

WARNINGS
Electric shock:

• Disconnect or turn off power before installing or servicing luminaire.

• Fixture should ONLY be powered on with access plate installed in fixture.

• All electrical wiring to be completed by a qualified licensed electrician in accordance with local and National/Canadian Electrical Code.

• Ensure supply voltage corresponds with the correct ballast/driver voltage.

• Avoid exposing wiring to metal edges and sharp objects.

• Ensure that the luminaire is properly grounded to prevent electric hazards.

• All supply field wiring to the luminaire shall be rated at 600v and 75°C Minimum
  Fire :

• Keep flammable and combustible materials away from the light source and/or lens.

• Use correctly rated supply conductors as indicated by product labeling.
  Burn:

• Allow luminaire to cool before handling luminaire.
  Personal Injury:

• Wear safety glasses and gloves when handling the luminaire to avoid
  physical injury.

• Avoid direct eye contact with light source.

• Always support the weight of the luminaire.
  Intended Use:

• Certain airborne contaminants can diminish integrity of acrylic and/or polycarbonate.

• Certain airborne contaminants may also adversely affect the functioning of LEDs and other electronic components, depending on various factors such as concentrations of the containments, ventilation, and temperature at the end-user location.

• Failure due to the effect of contaminants is not covered under our standard terms of warranty

Tools Required

WARNING
RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY

• LED retrofit kit installation requires knowledge of luminaires electrical system. If not qualified, do not attempt installation. Contact
  qualified electrician.

• Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.

• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or sharp objects.

• Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components.

• Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components.

Component List for Kit

• 1x Door Frame Assembly
•  2x Frame Angle Bracket
• 2x Tether Cables
• 1x Fixture Label

Cleaning and Maintenance
Use a damp, lint-free cloth to wipe lens. Don not use solvents or cleaners containing abrasive agents. When cleaning the fixture, make sure the power is turned off, and any liquid spray should be applied to the cleaning cloth and.

Retrofit Installation Instructions

1. Remove louver and ballast and discard
2.  Detail A: Insert pins to existing spring clips.

3. Detail B: Attach safety tethers to existing screw holes.

4. Connect power to LRK-TRH retrofit.

5. Close LRK-TRH by engaging other pins into spring clips.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>