KarliK EKlC20o Electronic Lightning Controller with Push and Rotary Button User Manual
- June 15, 2024
- KarliK
Table of Contents
USER MANUAL
ELECTRONIC LIGHTNING CONTROLLER WITH PUSH AND ROTARY BUTTON
Characteristics of electronic lightning controller with push and rotary
button
Electronic lightning controller with push and rotary button (dimmer switch)
enables stepless adjustment of light intensity from 0 to 100% of full power of
the illumination and it can be used with almost every frame.
With electricity consumption proportionate to the lightning level it increases
comfort and daily electricity savings.
Lightning controller is used to control illumination level of typical
incandescent lightning. Controlling involves the use of potentiometer with
switch. The configuration enables intelligent control of lightning systems and
is convenient and economic in use. The controller is equipped with overload
and short-circuit protection.
Technical data
| Symbol | …MR0-1 |
|---|---|
| Power supply | 230V 50Hz |
| Tolerance of voltage supply | -15 ÷ +10% |
| Light control | switch and regulation on potentiometer (10+100%) |
| Cooperation with load | convectional incandescent, halogen 230V, low voltage |
halogen 12V (with conventional and toroidal tranformer)
Load capacity| 40÷400W
Scope of regulation| 5÷40 oC
Control unit| triak
Number of connection clamps| 3
Cross section of connection cables| max 1,5 mm2
Fixing of the casing| standard flash-mounted wall box R 60mm
Temperature working range| from -20°C to +45°C
Withstand voltage| 2KV (PN-EN 60669-1)
Safety class| II
Surge voltage category| II
Contamination level| 2
Dimension with external frame| 80,0 x80,0x50,7
Protection index| IP 20
Warranty terms
The guarantee is provided for a term of twelve months from the date of
purchase. The defective controller must be delivered to the producer or to the
seller with a purchase document. The guarantee does not cover the fuse
exchange, mechanical damage, damages raised by self-repair or improper use.
The warranty period shall be extended by the duration of the repair.
ASSEMBLY MANUAL
Installation
- Deactivate the main fuses of home installation.
- Check if there is the phase wire brought into the installation box.
- Prise the regulatory button with use of screwdriver and remove it.
- Push clips on side walls of the external adapter with flat screwdriver and remove it.
- Pull out the intermediate frame from the dimmer module.
- Connect the phase wire to the clamp of the controlled load.
- Connect the other wire to the clamp with an arrow. (In case of dual-circuit system connect the third and the fourth wire to the clamp with an arrow.)
- Assemble the dimmer module in the installation box with resilient clips or fastening screws that are supplied with the box.
- Assembly the external frame with the intermediate frame.
- Assembly the dimmer and the control button.
- Activate the main fuses of home installation and carry out functional tests.
Electric connection scheme of the electronic lightning controller with push and rotary button
Accessories required to the electronic lightning controller with push and
rotary button
The electronic controller shall be equipped with an external single (MR-1)
or multiple (…MR-2+ …MR-5) frame which is available to buy in different colour
options made of plastic.
The product is compatible with DECO / MINI surface-mounted folding boxes. In
order to properly install the lighting regulator in the box, unscrew the metal
claws located at the mechanism.
Note! Assembly shall be held by a suitably qualified person with
deactivated voltage and shall meet the national safety standards.
Connecting two regulators in a two-way system may damage regulators.
Components of the electronic lightning controller with push and rotary
button
Installation instructions for electronic light controller mechanism in multiple frames
- First, install the electronic light control mechanism in the mounting box. The other adjacent mechanisms are installed so that the “dovetails”(1) (if any) overlap the central plate of the controller (2).
- The distance between the central frame of the dimmer and the adjacent products should be about 1 mm.
Karlik Elektrotechnik Sp. zo. o.
ul. Wrzesinska 29 | 62-330 Nekla | tel. +48 61 437 34 00
e-mail: karlik@karlik.pl |
www.karlik.pl
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>