VONN VAP2203 Lighting LED Multi Light Pendant Installation Guide
- June 4, 2024
- VONN
Table of Contents
INSTALLATION GUIDE
VONN LIGHTING MODEL#
VAP2203
TOOLS YOU MAY NEED
PARTS LIST
| A. Mounting Bracket x 1
B. Outlet Screw x 3
C. Wire Connector x 3
D. Ground Screw x 1
E. Canopy Cover Screws x 2|
---|---|---
LED INFO & WARNINGS
Please read and understand the entire manual before attempting to assemble,
operate, or install the product.| Make sure that you have all the necessary
parts by checking the parts list. If any part is missing or damaged please
contact VONN LIGHTING CUSTOMER SERVICE at
888-604-8666 for a replacement.
---|---
All parts must be used as indicated in these instructions. Do not substitute
any parts, leave parts out, or use any parts that are worn or broken.| Inspect
the LED fixture prior to installation to make sure that it has not been
damaged during shipping.
Please handle the LED light with care when unpacking. Do not apply pressure to
the LEDs, do not open any factory-sealed compartments, and do not touch the
LEDs with your hands.| VONN highly recommends using a qualified, licensed
electrician to install the fixture .
VONN recommends installing the fixture on its own independent circuit. Do
not install the fixture on the same circuit with the other appliances, or HVAC
systems.| Do not remove or replace VONN manufactured parts that are provided
with the fixture.
DO NOT CUT WIRES attached to the fixture under any circumstance. Cutting
wires will VOID your warranty. Excess cable should be neatly looped and tucked
into the canopy.| VONN recommends ELV (Electric Low Voltage) type dimmers
for this fixture.
Place the wall switch in the “OFF” position of the room you are installing the
fixture.| Shut “OFF” the electricity at the main fuse box.
Fixture Diagram
Instructions
Step 1. Adjust Height
The length of the cable is adjustable. To determine the proper length of the
fixture, hold the fixture canopy up against the outlet box in the ceiling to
adjust the cable.
Depress the locking pin on the canopy, hold the pin in place, and pull down or
push up on the cable. Repeat step for each cable.
Installer Tip (1): It is recommended that two installers are required to
adjust the height of the fixture. One installer to hold the fixture, and the
second installer to adjust the cables.
Step 2. Install Mounting Bracket
Secure mounting bracket (A) with outlet screws (B).
Step 3. Connect Wires
Supply Wires:
Connect Black (Line Wire) from fixture to Black (Hot Wire) from the outlet box.
Connect White (Neutral Wire) from fixture to White (Neutral Wire) from the
outlet box.
Ground Wires:
Connect Bare Copper (Ground Wire) from fixture to Green or Bare Copper (Ground
Wire) from the outlet box.
Twist wires together clockwise and secure with wire connector (C).
Installer Tip (2): If the ground wire is not available in the outlet box,
then secure Bare Copper (Ground Wire) from fixture to ground screw (D) on the
mounting bracket (A).
Installer Tip (3): It is recommended that two installers are required to
install the fixture. One installer to hold the fixture, and the second installer
to connect the wires.
Step 4. Mount Fixture
|
---|---
Secure canopy to mounting bracket (A) with canopy screws (E).
Step 5. Turn Power ON
Turn electricity “ON” at the main fuse box.
Place the recommended ELV type dimmer switch in the “ON” position to test the
fixture.
www.vonn.com
© VONN Lighting, 2022
Documents / Resources
| VONN
VAP2203 Lighting LED Multi Light
Pendant
[pdf] Installation Guide
VAP2203, Lighting LED Multi Light Pendant, VAP2203 Lighting LED Multi Light
Pendant, LED Multi Light Pendant, Multi Light Pendant, Light Pendant, Pendant
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>