Karlik ICUSB-8 Double USB Charger Instruction Manual

October 30, 2023
KarliK

Karlik ICUSB-8 Double USB Charger

Product Information

The ICUSB-8 Double USB Charger is a device designed to charge smartphones, tablets, and other electronic equipment. It has one USB-C port and one USB-A port. The charger works with a nominal input voltage of 100-240 V~ 50/60Hz and provides a nominal output current of 5V/3A, 9V/2.22A, 12V/1.67A (when device is connected to only one USB-C output) and 5V/3A, 9V/2A, 12V/1.5A (when device is connected to only one USB-A output). When two devices are connected, the output current is divided equally between each USB socket, and the maximum output power is 5V/3.1A. The charger has a detection function of available charger protocols for different devices.The ICUSB-8 Double USB Charger has a warranty period of 12 months from the date of purchase. Mechanical damages, defects resulting from unauthorized repairs and improper use of the product are not covered under warranty.

Product Usage Instructions

  1. Before connecting your device, check the charger’s compliance with the charging parameters of your device.
  2. The installation of the charger must be done by a person with sufficient qualifications, with power supply disconnected, and must comply with national safety standards.
  3. Connect the charger to the installation as shown in Figure 2. Improper connection may damage the charger or cause it to work incorrectly.
  4. If you’re using only one USB-C or USB-A output, refer to the detection function of available charger protocols to ensure compatibility with your device.
  5. If you’re using both USB-C and USB-A outputs, refer to the detection function of available charger protocols to ensure compatibility with your device.
  6. If the ICUSB-8 charger becomes defective during the warranty period, send the charger along with the proof of purchase to the manufacturer or seller for repair. Warranty period will be extended for the duration of the repair.

DOUBLE USB CHARGER

Specification of ICUSB-8 double USB charger
The ICUSB-8 charger is intended to charge devices like smartphones, tablets and other electronic equipment. Before connecting the device, check compliance of the charger with charging parameters of the given device.

Specification

Number of USB ports (type C) 1
Number of USB ports (type A) 1
Nominal input voltage 100-240 V~ 50/60Hz
Nominal output current Ÿ  5V/3A, 9V/2.22A, 12V/1.67A (when device is

connected to only one USB-C output)

Ÿ  5V/3A, 9V/2A, 12V/1.5A (when device is connected to only one USB-A output)

Ÿ  5V/3.1A (in the case of connecting devices to two outputs, the output current is divided equally between each USB socket)

Maximum output power| 20 W
Maximum power consumption in idle mode| 0.1 W
Operating temperature and humidity| -10 ÷ +400C; 20~90% RH
Storage temperature and humidity| -20 ÷ +850C; 10~95% RH
Ingress protection degree| IP 20

Detection function of available charger protocols:

  • when using only one USB-C or USB-A output
    APPLE| 5V 2.4A
    ---|---
    BC 1.2| DCP 5V 1.5A
    SAMSUNG AFC| 9V
    HUAWEI FCP| 5V, 9V, 12V
    SCP| –
    QC 2.0| 5V, 9V, 12V
    QC 3.0| 11.70V max
  • when using both USB-C and USB-A outputs
    APPLE| –
    ---|---
    BC 1.2| DCP 5V 1.5A
    SAMSUNG AFC| 9V
    HUAWEI FCP| –
    SCP| –
    QC 2.0| 5V, 9V, 12V
    QC 3.0| –

Warranty conditions

Warranty is granted for a period of 12 months of the date of purchase. The defective ICUSB-8 charger along with the proof of purchase should be sent to the manufacturer or to the seller. Warranty does not include mechanical damages, defects resulting from unauthorised repairs and improper use of the product.
Warranty period will be extended for the duration of the repair.

ASSEMBLY INSTRUCTIONS

  1. Remove the glass panel (1) with the label applying a knife or a flat screwdriver in the recess (3).
  2. Unscrew the screw (2) and pull out the adapter (3) together with the USB charger module (4). If necessary, you can detach the USB charger module (4) from the adapter (3) by simultaneously pressing the two movable clips on the USB charger module (4).
  3. Dismantle the USB charger modules (4).
  4. Remove the spacer frame (5) from the assembly block (7). Pull away the block tabs or pull the frame tightly to do this.
  5. Set the assembly block in the box (9) with tabs or screws at the box (8).
  6. Connect the power cable to the terminal block of the USB charger module (see figure 2), respectively the phase wire under the “L” terminal, the neutral wire under the “N” terminal.
  7. Insert the intermediate with the USB charger module (4) into the intermediate frame (5) and screw it onto the mounting block (7) with the screw (2).
  8. Attach the label and glass pane.

NOTE!
The installation must be done by a person with sufficient qualifications, with power supply disconnected, and must comply with national safety standards.
The connection to the installation should be done as shown in Figure 2. With improper connection, the charger may be damaged or may work incorrectly.

Contact

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals