Karlik DCUSB-7 Double USB Charger User Manual
- June 12, 2024
- KarliK
Table of Contents
USER MANUAL – DCUSB-7
DOUBLE USB CHARGER
DCUSB-7 Double USB Charger
Specification of DCUSB-7 double USB charger
The DCUSB-7 charger is intended to charge devices like smartphones, tablets
and other electronic equipment. Before connecting the device, check compliance
of the charger with charging parameters of the given device.
Dane techniczne
Number of USB ports (type C) | 2 |
---|---|
Nominal input voltage | 100-240 V~ 50/60Hz |
Nominal output current | • 5V/3A, 9V/2.22A, 12V/1.67A (when device is connected |
to only one USB output)
• 5V/3.1A (in the case of connecting devices to two outputs, the output
current is divided equally between each USB socket)
Maximum output power| 20 W
Maximum power consumption in idle mode| 0.1 W
Operating temperature and humidity| -10 ÷ +40 C; 20~90% RH
Storage temperature and humidity| -20 ÷ +85 C; 10~95% RH
Ingress protection degree| IP 20
Detection function of available charger protocols:
– when using only one USB-C output
APPLE | 5V 2.4A |
---|---|
BC 1.2 | DCP 5V 1.5A |
SAMSUNG AFC | 9V |
HUAWEI FCP | 5V, 9V, 12V |
SCP | – |
QC 2.0 | 5V, 9V, 12V |
QC 3.0 | 11.70V max |
– when using both 2 x USB-C outputs
APPLE | – |
---|---|
BC 1.2 | DCP 5V 1.5A |
SAMSUNG AFC | 9V |
HUAWEI FCP | – |
SCP | – |
QC 2.0 | 5V, 9V, 12V |
QC 3.0 | – |
Warranty conditions
Warranty is granted for a period of 12 months of the date of purchase. The
defective DCUSB-7 charger along with the proof of purchase should be sent to
the manufacturer or to the seller. Warranty does not include mechanical
damages, defects resulting from unauthorised repairs and improper use of the
product.
Warranty period will be extended for the duration of the repair.
ASSEMBLY INSTRUCTIONS
- Remove the glass panel (1) with the label applying a knife or a flat screwdriver in the recess (3).
- Unscrew the screw (2) and pull out the adapter (3) together with the USB charger module (4). If necessary, you can detach the USB charger module (4) from the adapter (3) by simultaneously pressing the two movable clips on the USB charger module (4).
- Dismantle the USB charger modules (4).
- Remove the spacer frame (5) from the assembly block (7). Pull away the block tabs or pull the frame tightly to do this.
- Set the assembly block in the box (9) with tabs or screws at the box (8).
- Connect the power cable to the terminal block of the USB charger module (see figure 2), respectively the phase wire under the “L” terminal, the neutral wire under the “N” terminal.
- Insert the intermediate with the USB charger module (4) into the intermediate frame (5) and screw it nto the mounting block (7) with the screw (2).
- Attach the label and glass pane.
NOTE!
The installation must be done by a person with sufficient qualifications, with
power supply disconnected, and must comply with national safety standards.
The connection to the installation should be done as shown in Figure 2. With
improper connection, the charger may be damaged or may work incorrectly.
Karlik Elektrotechnik Sp. z o. o.
ul. Wrzesihska 29 I 62-330 Nekla
tel. +48 61 437 34 00
e-mail: karlik@karlik.pl
www.karlik.pl
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>