Cloud C82T CVS Series In Ceiling Loudspeakers Installation Guide
- June 13, 2024
- CLOUD
Table of Contents
Cloud C82T CVS Series In Ceiling Loudspeakers Product Information
The CVS Series In-Ceiling Loudspeakers are a range of high-quality speakers designed for installation in ceilings. They come in various models, including CVS-C5, CVS-C5T, CVS-C52T, CVS-C53T, CVS-C62T, CVS-C82T, and CVS-C83T. Each model has different specifications and power ratings.
- Rated Power: The rated power ranges from 10W to 25W, depending on the model.
- Max Power: The maximum power handling capacity ranges from 20W to 50W, depending on the model.
- Depth Required: The depth required for installation above the ceiling varies between models, ranging from 169mm to 248mm.
- Line Transformer Power Tappings: All models have multiple power tapping options, ranging from 6W to 24W, and an impedance of 8 ohms.
- Color Options: The models are available in either black (suffix ‘B’) or white (suffix ‘W’) finishes.
- Front Grilles: Most models have integral front grilles, except for CVS-62T and CVS-83T, which have removable front grilles.
Product Usage Instructions
Step 1: Cut a Hole in the Ceiling
Using the template provided, cut a hole at the desired mounting location in
the ceiling. Refer to the table above to ensure that the diameter of the hole
matches the requirements for the specific model. Before cutting, make sure
there are no cables or obstructions behind the mounting surface.
Step 2: Prepare the Wires
Strip the ends of the wires coming from the amplifier. Insert the stripped
ends into the spring-loaded terminal block connector on the loudspeaker. No
screwdriver is required for this connection. Choose the appropriate power
tapping by connecting the wires to the corresponding terminals on the
connector. The power tap selection is described on the magnet sticker on the
rear side of the loudspeaker. If using 100/70/25 V speakers in low impedance
mode (8 ohms), disconnect the ground wires by interrupting the cable lugs.
Step 3: Mount the Speaker
Ensure that the mounting clamps are fully bent inwards to allow the speaker to
fit through the cut-out. Insert the speaker into the opening.
Step 4 (For Models with Removable Grilles): Secure the Speaker
If your model has a removable grille, fix the speaker in the provided opening
by tightening the screws of the mounting clamps using a screwdriver. A quarter
turn will cause the mounting clamps to flip-out and lock the speaker in place.
Continue tightening the screws until the speaker unit is fully secure.
Step 5: Finalize Installation
Once the speaker is securely mounted, it is now correctly installed and ready
for use.
CAUTION – Installation
Speaker must be installed by a qualified speaker technician.
CAUTION – Servicing
The unit contains no user-serviceable parts. Refer servicing to qualified
personnel.
Do not perform servicing unless you are qualified to do so.
CAUTION – Tap Settings
Before use, check that the transformer is set to the correct power tapping for
the system.
INFORMATION
Model
| Rated power| Max Power| ****
Cut-out diameter
| Depth required above ceiling| Line transformer power
tappings (100 V-line) or impedance
---|---|---|---|---|---
CVS-C5| 10 W| 20 W| 169 mm (6.65″)| 65 mm (2.56″)| 16 ohms
CVS-C5T| 10 W| 20 W| 169 mm (6.65″)| 65 mm (2.56″)| 6 W / 3 W / 1.5 W / 8 ohms
CVS-C52T| 20 W| 40 W| 169 mm (6.65″)| 65 mm (2.56″)| 6 W / 3 W / 1.5 W / 8
ohms
CVS-C53T| 20 W| 40 W| 169 mm (6.65″)| 65 mm (2.56″)| 24 W / 12 W / 6 W / 8
ohms
CVS-C62T| 25 W| 50 W| 205 mm (8.07″)| 105 mm (4.13″)| 24 W / 12 W / 6 W / 8
ohms
CVS-C82T| 25 W| 50 W| 241 mm (9.49″)| 92 mm (3.62″)| 24 W / 12 W / 6 W / 8
ohms
CVS-C83T| 25 W| 50 W| 248 mm (9.76″)| 110 mm (4.33″)| 24 W / 12 W / 6 W / 8
ohms
Note: all model numbers are suffixed either ‘B’ or ‘W’. This refers to
the colour of the finish: ‘B’ = black, ‘W’ = white.
All models have integral front grilles, with the exception of Models CVS-62T
and CVS-83T, which have removable front grilles.
Installation Instruction
-
Cut a hole at the mounting location in the ceiling using the template supplied. You can check that the diameter is correct for the model by referring to the table above.
Double check that there are no cables or other obstructions behind the mounting surface before making the cut-out. -
Strip the ends of the wires coming from the amplifier and insert in the spring-loaded terminal block connector on the loudspeaker. No screwdriver is required.
The correct power tapping is chosen by connecting to the appropriate terminals of the connector. A description of the power tap selection is shown on the magnet sticker on the rear side of the loudspeaker.
When using 100/70/25 V speakers in low impedance mode (8Ω), disconnect the ground wires by interrupting the cable lugs.
- Make sure the mounting clamps are fully bent inwards, allowing the speaker fit through the cut-out. Insert the speaker to the opening.
- Fix the speaker in the provided opening by tightening the screws of the mounting clamps using a screwdriver. A quarter turn will cause the mounting clamps to flip-out, locking the speaker in place. Tighten the screws further until the speaker unit is fully secure.
- To attach the grill to the speaker, insert the lips into the provided openings on the speaker baffle and rotate it a partial turn (15°) to lock it into place.
- The speaker is now correctly installed and ready for use.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>