Weller WXMPS MS WXsmart Tools Tweezers User Manual
- June 15, 2024
- Weller
Table of Contents
Weller WXMPS MS WXsmart Tools Tweezers User Manual
https://www.weller-tools.com/wxsmart
⚠ WARNING Electrical shock
Protect yourself against electric shocks. The handles on soldering tools with
an antistatic design are conductive.
- Avoid touching earthed objects such as pipes, heaters, cookers and refrigerators.
- Do not use the soldering tool in a damp or wet environment.
- Never work on voltage-carrying parts.
⚠ WARNING Risk of burns
The soldering tip becomes very hot during soldering work. There is a risk of
burns from touching the tips. After the soldering process, the soldering tool
and the workpiece holder are still hot.
- Always place the soldering tool in the safety rest while not in use. Make sure the safety holder is stable.
- Do not touch the hot soldering tips and keep them away from inflammable objects..
- Only replace solder tips when cold
- Only replace nozzles when cold
Risk of burning through liquid solder. Protect yourself against solder splashes.
- Wear appropriate protective clothing to protect yourself against burns. Protect your eyes by wearing eye protection.
- When working with adhesives, special attention must be paid to the warning information provided by the adhesive manufacturer.
- Only connect the vacuum and hot air at the designated points.
Store your soldering tool in a safe place. When not in use, units and tools
should be stored in a dry, high or locked area out of the reach of children.
Make sure that unused soldering tools are free of voltage and de-pressurised.
Do not use the cable for purposes other than those for which it is intended.
Never carry the unit by the cable. Do not use the cable to pull the plug out
of the socket. Protect the cable against heat, oil and sharp edges.
Be alert. Pay attention to what you are doing. Be smart when using the unit.
Do not use the soldering tool if you are having difficulty concentrating.
Avoid abnormal posture. Arrange your work station in an ergonomically correct
way. Avoid bad posture when using the unit, as this can lead to postural
problems.
The soldering tool must be operated only in perfect technical working order.
Safety devices must not be deactivated.
Faults and defects must be repaired immediately. Before using the unit / tool,
safety devices must be carefully checked to make sure that they are
functioning properly and in the manner intended. Check that moving parts are
functioning properly and are not sticking, and whether parts are damaged. All
parts must be correctly fitted and must satisfy all the requirements necessary
to guarantee trouble free operation of the unit.
Use the correct tool. Use only accessories or auxiliary devices which are
included in the list of accessories or approved for use by the manufacturer.
Use WELLER accessories or auxiliary devices on original WELLER equipment only.
The use of other tools and other accessories can cause injury.
Secure the tool. Use clamping fixtures to hold the workpiece.
Use a solder fume extraction unit. If appliances for connecting solder fume
extraction units are available, ensure that they are connected and used
properly.
Specified Conditions Of Use
Use the soldering iron exclusively for the purpose indicated in the Operating
Instructions of soldering and desoldering under the conditions specified here.
The soldering iron may only used in combination with Weller Supply Units. This
device may only be used at room temperature and indoors. Protect against
moisture and direct sunlight.
User groups
Due to differing degrees of risk and potential hazards, several work steps may only be performed by trained experts.
Care and maintenance
⚠ WARNING
Before doing any work on the machine, pull the plug out of the socket. Leave
the unit to cool down.
Check all connected cables and hoses on a regular basis. If power tools are
damaged, they must be immediately removed from use.
Do not use blocked nozzles.
Repairs must always be referred to a Weller-trained specialist. Use original
replacement parts only.
⚠ WARNING Risk of burns
- Only replace the soldering tips when they are cold.
The soldering tool must be left switched off in the safety rest for at least 3 minutes until the soldering tip has cooled down. The LED status indicator must be at ,,OFF”.
Temperature performance
The soldering tool has an internal usage sensor which can be used to set an automatic switch-off function (Stand-by). The settings can be found in the station’s operating instructions.
Warranty
Claims by the buyer for physical defects are time-barred after a period of one year from delivery to the buyer. This does not apply to claims by the buyer for indemnification in accordance with §§ 478, 479 BGB (German Federal Law Gazette). We shall only be liable for claims arising from a warranty furnished by us if the quality or durability warranty has been furnished by use in writing and using the term ,,Warranty”. The warranty shall be void if damage is due to improper use and if the device has been tampered with by unauthorized persons. For more information please visit www.weller- tools.com.
Symbols
Technical Data
Subject to technical alterations and amendments.
EC declaration of conformity
We hereby declare that the products described herein comply with the following
guidelines:
2014/35/EU, 2014/30/EU, 2006/42/EG
Besigheim, 2023-02-07
Philippe Buidin
Managing director
Authorised to compile technical documentation.
SI 2016 No.1101, SI 2016 No.1091, SI 2008 No.1597
Besigheim, 2023-02-07
Philippe Buidin
Managing director
Authorised to compile technical documentation.
For Weller Tools GmbH
Apex Tool Group UK Ltd
Registered in England, Company Number 14127816
Registered Office:
20 Farringdon Street, 8th Floor
London, EC4A 4AB, United Kingdom
Product Registration
www.weller-tools.com/registration
GERMANY
Weller Tools GmbH
Carl-Benz-Straße 2
74354 Besigheim
Tel: +49 (0) 7143 580-0
CHINA
Apex Tool Group
Room 302A,
NO 177 Bibo Road
Shanghai, 201202
Tel: +86 (21) 60880288
THE NETHERLANDS
Apex Tool Group B. V.
Phileas Foggstraat 16
7821 AK Emmen
Tel: +31 (0) 591 66 75 00
GREAT BRITAIN
Apex Tool Group UK Ltd
Registered in England,
Company Number 14127816
Registered Office:
C/O TMF Group 13th Floor,
One Angel Court, London,
EC2R 7HJ, United Kingdom
Tel: +44 740 8836 404
USA
Apex Tool Group, LLC.
Weller Professional Tools Division
1000 Lufkin Road
Apex, NC 27539
Tel: +866-498-0484
info@weller-tools.com
www.weller-tools.com
© 2023, Apex Tool Group, LLC.
Weller is a registered Trademark and registered Design of Apex Tool Group,
LLC.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>