Bellini BDG604G Glass Built In Gas Cooktop User Manual

: June 15, 2024
: Bellini

BDG604G Glass Built In Gas Cooktop

Product Information

Specifications

Model No.:
- BDG604G, BDG604G-F FINELINE: 5102880 Aus/NZ
- BDG302WG, BDG302WG-F FINELINE: 5102875 Aus Only
- BDG301G, BDG301G-F FINELINE: 5102876 Aus Only
Manufacturer: GSM Retail Australia Pty Ltd
ABN: 53 007 682 475
Warranty: 3 years in-home warranty

Product Description

The Bellini Glass Built-In Gas Cooktop is a high-quality cooking
appliance designed for domestic use. It features a glass ceramic
surface and offers multiple cooking zones for versatile cooking
options.

Safety Instructions

It is important to follow the safety instructions to ensure
proper usage and avoid any accidents. Please read the following
safety instructions carefully:

General Safety

Additions or modifications to the appliance are not
permitted.
An authorized service person must install the appliance and
provide a Certificate Of Compliance. Keep the certificate along
with your proof of purchase.
Do not place or store flammable liquids, highly inflammable
materials, or fusible objects (e.g., plastic film, plastic,
aluminum) on or near the appliance.
Built-in appliances should only be used after they have been
installed in suitable built-in units and work surfaces that meet
local authority standards.
Do not heat an empty pan on the appliance.

Children’s Safety

The cooking zones will become hot when in use. Keep small
children away from the appliance.
The appliance is not intended for use by young children or
infirm persons without supervision.
You should supervise young children to ensure they do not play
with the appliance.

Safety During Use

Remove stickers and film from the glass surface before
use.
In case of faults with the appliance or damage to the glass
ceramic (cracks, scratches, or splits), switch off and disconnect
the appliance from the electrical supply to prevent the possibility
of electric shock.
Repairs to the appliance must only be carried out by trained
registered authorized service persons/engineers.
Consult the reference data plate located on the underside of
the appliance for technical and identification data before making
electrical connections.

Installation

Proper installation is crucial for the safe and efficient
operation of your Bellini Glass Built-In Gas Cooktop. Follow these
steps for installation:

Ensure you have all the necessary tools and materials for
installation.
Read the installation section of the user manual thoroughly
before starting.
Select a suitable location for the cooktop that meets local
authority standards.
Prepare the work surface according to the provided
specifications.
Follow the step-by-step instructions provided in the user
manual for connecting the gas supply and electrical
connections.
Double-check all connections to ensure they are secure.
Test the cooktop to ensure it is functioning properly before
regular use.

Start Using Your Appliance

Once the installation is complete, you can start using your
Bellini Glass Built-In Gas Cooktop. Follow these guidelines:

Ensure the cooktop is clean and free from any debris or
packaging materials.
Place your cookware on the desired cooking zone. Make sure the
size of the cookware matches the size of the cooking zone.
Turn the corresponding knob to ignite the gas burner. Adjust
the flame intensity using the control knob.
Monitor the cooking process and adjust the flame as needed to
achieve the desired heat level.
After use, turn off the gas burner and allow the cooktop to
cool down before cleaning.

Maintenance

Regular maintenance will help prolong the lifespan and
performance of your Bellini Glass Built-In Gas Cooktop. Follow
these maintenance tips:

Ensure the cooktop is cool before cleaning.
Clean the glass surface with a non-abrasive cleaner and a soft
cloth or sponge.
Remove any stubborn stains using a mild detergent or
specialized glass cleaner.
Do not use abrasive materials or harsh chemicals that may
damage the glass surface.
Wipe off any spills or food debris immediately to prevent them
from hardening or causing stains.

Warranty

Your Bellini Glass Built-In Gas Cooktop comes with a 3-year
in-home warranty. To avail of the warranty and for any technical
queries, please contact the following:

Australia: 1300 373 199
New Zealand: 0800 764 912
Website: www.belliniappliances.com.au

FAQ

Q: Can I modify the appliance?

A: No, modifications to the appliance are not permitted.

Q: Who should install the appliance?

A: An authorized service person must install the appliance and
provide a Certificate Of Compliance.

Q: Can I heat an empty pan on the cooktop?

A: No, do not heat an empty pan on the appliance.

Q: How should I clean the glass surface?

A: Clean the glass surface with a non-abrasive cleaner and a
soft cloth or sponge. Avoid using abrasive materials or harsh
chemicals that may damage the glass.

Q: What should I do in case of faults or damage?

A: In case of faults or damage to the appliance, switch it off,
disconnect it from the electrical supply, and contact trained
registered authorized service persons/engineers for repairs.

USER MANUAL

Glass Built In Gas Cooktop
Model No. BDG604G, BDG604G-F FINELINE: 5102880 Aus/NZ BDG302WG, BDG302WG-F FINELINE: 5102875 Aus Only BDG301G, BDG301G-F FINELINE: 5102876 Aus Only

GSM Retail Australia Pty Ltd ABN: 53 007 682 475 For Warranty and technical queries: Australia 1300 373 199 For Warranty and technical queries: New Zealand 0800 764 912 www.belliniappliances.com.au

V19 October 2023

Thank you.
Thank you for choosing Bellini Appliances. This Bellini appliance carries a 3 year in home warranty, be
sure to retain your user manual and receipt. For all warranty and technical queries please phone:
Australia 1300 373 199 New Zealand 0800 764 912
GSM Retail Australia Pty Ltd ABN: 53 007 682 475 For Warranty and technical queries: Australia 1300 373 199 For Warranty and technical queries: New Zealand 0800 764 912 www.belliniappliances.com.au

Contents
Safety instructions —————————– 2 Product description —————————-4 Installation —————————————-6 Start using your appliance ——————- 10 Maintenance ———————————— 12 Warranty —————————————— 14
3

Safety Instructions

This manual explains the proper installation and use of your appliance, please read it

carefully before using even if you are familiar with the product. The manual should be

kept in a safe place for future reference. In case of failure, only the Authorized Technical

Service may repair this hob. Otherwise the guarantee will be null and void. All Bellini

Appliances are for domestic use only.

Warning

General Safety

Additions or modifications to the appliance

An authorised service person must install this

are not permitted.

appliance and MUST provide a Certificate Of

Do not place or store flammable liquids,

Compliance. This certificate should be retained

highly inflammable materials or fusible

along with your proof of purchase.

objects (e.g. plastic film, plastic, aluminum) on

Built-in appliances may only be used after they have

or near the appliance.

built in to suitable built-in units and work surfaces

Do not heat an empty pan on the appliance.

that meet local authoritystandards.

Children’s Safety

In the event of faults with the appliance or damage

The cooking zones will become hot when you

to the glass ceramic(cracks, scratches or splits), the

cook. Therefore, always keep small children

appliance must be switched off and disconnected

away from the appliance.

from the electrical supply, to prevent the possibility

The appliance is not intended for use by

of an electric shock.

young children or infirm persons without

Repairs to the appliance must only be carried out by

supervision.

trained registered authorized service persons /

Young children should be supervised to

engineers.

ensure that they do not play with the

The technical and identification data for the hob is

appliance.

located on the reference data plate fixed to the

Safety During Use

underside of the appliance.

Remove stickers and film from the glass

This reference data plate must be consulted before

surface.

making the electrical connections.

There is the risk of burns from the applianceif

The electrical connections must be made by

used carelessly.

specialist installers to the legal and regulatory,

Cables from electrical appliances must not

requirements in each country.

touch the hot surface of the appliance or hot

If the cable is damaged in any way it must be

cookware.

replaced by the manufacturer or after sale service

Overheated fats and oils can ignite very

or by authorized technical staff, to avoid hazard.

quickly. Warning! Fire hazard!

Correct Use

Switch the cooking zones off after each use.

People (including children) who, because of their

Users with implanted pacemakers should

physical, sensory or mental capabilities or their

keep their upper body at least 30 cm from

inexperience or ignorance are not able to use the

cooking zones that are switched on.

device safely, should not use this device without

Risk of burns! Do not place objects made of

supervision or instruction by a responsible person.

metal, such as knives, forks, spoons and

This appliance should be used only for normal

saucepan lids on the cooking surface, as they

domestic cooking and frying of food.

can get hot.

The appliance must not be used as a work surface

or as a storage surface.

2

Safety Instructions
Safety When Installation Do not use or store flammable materials in the
appliance storage drawer or near this appliance. Do not spray aerosols in the vicinity of this
appliance while it is in operation. This appliance shall not be used as a space
heater. This hotplate must be installed in accordance
with: AS 5601 – Gas Installations (for Australia) current edition NZS 5261 Code of Practice for the Installation of Gas Burning Appliances and Equipment (for New Zealand) This standard may not be now current!! Local gas fitting regulations AS/NZS 3000 Electrical Installations (Wiring Rules) Building codes Any other relevant statutory regulations. Check the gas type label on the underside of the hotplate, adjacent to the gas connection to ensure it corresponds to the installation gas supply. If in doubt contact the supplyauthority. The power supply cord (supplied) must not touch
against any hot surfaces and must be placed so
that its temperature does not exceed 75 degrees
at any point along its length. After connecting to gas, check for leaks using
soapy solution, never a naked flame. Where a flexible hose assembly is used, ensure it
is approved to AS/NZS 1869, Class B10mm

diameter and no more than 1.0metre in length. Any hose assembly used must be restrained from accidental contact with the flue outlet of an under bench oven. How To Avoid Damage To The Appliance The glass surface can be damaged by objects falling onto it. The edge of the glass ceramic can be damaged by being knocked by the cookware. Cookware made of cast iron, cast aluminum or with damaged bottoms can scratch the glass surface if pushed across the surface. Objects that melt and things that boil over can burn onto the glass surface and should be removed straightaway. Do not use the cooking zones with empty cookware or without cookware. To avoid damaging cookware and glass ceramics, do not allow empty saucepans or frying pans to keep heating by the hob. The ventilation gap of 5mm between the worktop and front of the unit underneath it must not be covered. Do not modify this appliance.
Safety When Cleaning For cleaning, the appliance must be switched off
and cooled down. For safety reasons, the cleaning of the appliance
with steam jet or high pressure cleaning equipment is not permitted.

Disposing Of The Device When disposing of the device, do not bring it to regular municipal waste containers. Instead, bring it to electrical and electronic waste recycling and reuse center. A relevant label has been put on the device, its instructions manual, or the package. The device has been manufactured of recyclable material. By bringing old device to recycling collection center, you show that you care about nature. Ask your local environmental care authority for information on location of such facilities.

3

Product Description

Burner

BDG604G, BDG604G-F

have no aluminum trim
Trivet

BDG302WG, BDG302WG-F,

have no aluminum trim

Aluminum trim Control knobs
BDG301G,BDG301G-F,

have no aluminum trim

Burner

Trivet

Aluminum trim

Control knobs 4

Accessory Name
User Manual Sealing tape
Additional labels

Picture ( for reference only, physical unit maybe different)
You have additional rating label in accessory bag, suggest attach it onto a surface where it can be read e.g. inside surface of adjacent cupboard

Quantity
1 1 roll
1 set

Installation clip
Screws ST4.2×24

for BDG302WG(-F)&BDG301G(-F)

LPG Injectors

for BDG604G(-F)

4 sets

5 for BDG604G(-F) and

BDG302WG(-F)&BDG301G(-F)

BDG604G(-F)

0.55mmx1, 0.7mmx2, 0.98mmx1

BDG302WG(-F)

0.7mmx1, 0.98mmx1

BDG301G(-F)

0.98mmx1

Elbow &Washers

1 Elbow, 3 washers

Natural gas 1
regulator Test point
1 adapter

Technical Specifications

Model

Product Dimensions (h x w x d) mm

Cut-out Size
( w x d)mm

BDG604G(-F)

105x584x510 552 x 470

BDG302WG(-F) 100x300x510 266 x 478

BDG301G(-F)

100x300x510 266 x 478

App’x net weight
12.7Kgs
7 Kgs
6 Kgs

Electrical Connectio n
220-240V/50Hz
220-240V/50Hz
220-240V/50Hz

Rated Input Powe r 0.5W
0.5W
0.5W

5

NOTE: On completion of the installation of the cooktop to the kitchen bench, the distance from benchtop surface to the highest part of any trivet is 55.5 mm as shown in illustrations.
Installation
Before Installation:
Before cutting into any bench tops, ensure the minimum clearances to walls, adjacent surfaces dna overhead surfaces required by the relevant gas appliance installation code (see above) will comply. Dimensions are specified in millimeters (mm) Overhead cupboards and range hood = 650 mm. Side and rear clearance = 200 mm to any burner edge. Overhead exhaust/ceiling fan = 750 mm Horizontal surfaces adjacent the hob = less than or equal to the hob height. Ensure there is sufficient clearance to fit the regulator and/or flexible hose connection with the hotplate in the installed position.
Where range appliance or rangehood is replaced, the overhead clearance from the highest part of the highest burner of the appliance (or hob) to the rangehood shall not be less than 600mm unless the appliances manufacturer’s instructions specifies a greater clearance.
When you have installed the hob, make sure that
The GPO(general purpose outlet) must always be in an accessible position. The supply connection point, test point and natural gas regulator adjustment screw (for Natural gas
installation) are accessible for testing and/or adjustment with the hotplate in the installed position.
TO BE INSTALLED ONLY BY AN AUTHORIZED PERSON.
1. Cupboard Cutting Bench top thickness, 30 40 mm (3 4 cm).

BDG604G/BDG604G-F

BDG302WG/BDG302WG-F

BDG301G/BDG301G-F

6

2. Place Burner Box Apply the adhesive sealing tape to the underside lip of the burner box. Shown at G opposite. Place burner box into cutout hole and fit clamping brackets to clamp the hotplate to the bench. Installation of clips: step 1- put the clip inside the edge of the hole(image 1)
step 2- fix the installation braket with screw(image 2)

image 1

image 2

3. Fit Burners And Trivet. Replace burners and ensure they are correctly repositioned over the ignitor (S) and thermocouple (T). The ignitor (S) must be clean for trouble free sparking. Test burner ignition and burner flame for correct operation, If burner is placed correctly it will not rotate on its supports..

The Triple Ring (Wok) burner (diagrams below) does not fit over the igniter or thermocouple but must be placed on its supports. Make sure trivet is fitted onto its locator on burners and can’t rotate after assembled.

4. Electrical Connection Install a 10 amp general purpose outlet (GPO) in accordance with relevant electrical standards and/or codes of practice applicable. The power supply cord (supplied) must not touch against any hot surfaces and must be placed so that its
7

temperature does not exceed 75oC at any point along its length. After having installed the hotplate, the GPO must always be in an accessible position.

Wiring diagram for BDG604G(-F)

Wiring diagram for BDG302WG(-F)

Wiring diagram for BDG301G(-F)
5. Gas Connection Install in accordance with relevant gas standards and/or codes of practice applicable. Connect the elbow fitting to the appliance gas manifold connection, and check that seals between the elbow and manifold connection are in place and in good condition. For Natural gas: connect the natural gas appliance regulator (pictured
opposite) with integral test point using approved gas thread tape or compound to the elbow fitting. For Universal LPG: connect the brass test point adaptor (pictured opposite) using approved gas thread tape or compound to the elbow fitting. Ensure the supply connection point, test point and natural gas regulator adjustment screw (for Natural gas installation) are accessible for testing and/or
adjustment with the hotplate in the installed position. Where a flexible hose assembly is used, ensure it is approved to AS/NZS 1869, Class B. Any hose assembly used must be restrained from accidental contact with the flue outlet of an under bench oven. This hose assembly shall be suitable for connection to a fixed consumer piping outlet located as follows: Hotplates at a point 800 mm to 850 mm above the floor and in the region outside the width of the appliance to a distance of 250 mm.

After connecting to gas, check for leaks using soapy solution, never a naked flame.

Inlet connection region for flexible hose

8

Fit the duplicate data plate (supplied in separate bag) on a surface adjacent to the hotplate, for example, the inside of the cupboard door so it is clearly visible for any service technician.
SETTING THE GAS PRESSURE: Fit a manometer with a 6 mm rubber hose to the test point on the regulator (for natural gas).
For the Model BG604G(-F), light Triple Ring and Auxiliary burner on and adjust test point pressure to 1.00 kPa. Turn the two burners off and on again and recheck the pressure is same as set previously or adjust as required. For all the other models, light all burners on and adjust test point pressure to 1.00 kPa. Turn burners off and on again and recheck the pressure is same as set previously or adjust as required. TEST FOR CORRECT OPERATION: After installation and adjusting burner pressure using test point, each burner ignition and operation must be tested individually and with all burners operating. This testing must be done by the installer before leaving.
ADJUSTING THE BURNER MINIMUM FLAME HEIGHT: NOTE: This adjustment can only be performed by the installer or an authorised service personnel. The minimum burner flame is factory adjusted for the gas type stated on the gas type label adjacent to the gas connection and should not require adjustment. Adjustment may be required if the hotplate has been converted from Natural gas to Universal LPG or vice versa. GAS CONVERSION INSTRUCTIONS: The manufacturers servicing instructions detail how authorised personnel may convert the hotplate from Natural gas to Universal LPG or from Universal LPG to Natural gas. Contact the manufacturer or agent as required.

Model BDG604G(-F) Auxiliary Semi rapid x2 Wok TOTAL NHGC Model BDG302WG(-F) Semi rapid Wok TOTAL NHGC Model BDG301G(-F) Wok
TOTAL NHGC

NATURAL GAS

Injector Dia(mm) MJ/h Test point kPa

0.9

4

1

1.1

6

1

1.7

12.5

1

28.5

NATURAL GAS

Injector Dia(mm) MJ/h Test point kPa

1.1

6

1

1.7

12.5

1

18.5

NATURAL GAS

Injector Dia(mm) MJ/h Test point kPa

1.7

12.5

1

UNIVERSAL LPG

Injector Dia(mm) MJ/h Test point kPa

0.55

3.4

2.75

0.7

5.5

2.75

0.98

10.8

2.75

25.2

UNIVERSAL LPG

Injector Dia(mm) MJ/h Test point kPa

0.7

5.5

2.75

0.98

10.8

2.75

16.3

UNIVERSAL LPG

Injector Dia(mm) MJ/h Test point kPa

0.98

10.8

2.75

12.5

10.8

9

Start Using Your Appliance

Description
Zone indicators Flame power

Explanation These show which zone is under control.
Flame power of the zones, is the lowest and is the highest.

The hotplates are fitted with mains powered electronic spark ignitors, so must be connected to mains power supply (i.e. nominal 230 V ac) to operate. If power is not available, the hotplate will still work but the burners will have to be lit with a match or similar.
Depressing the gas control knob of any burner will activate the spark ignition for all burners. To light the burner, turn the gas control knob to the High Flame setting of the burner to be lit, while at the same time depressing the gas control knob to activate the spark ignition.
Once the burner is alight continue to depress the gas control knob for 5 10 seconds to allow the flame safeguard to activate. If when you release the gas control knob, the burner flame goes out the flame safeguard has not heated up enough so repeat the ignition procedure after waiting 1 minute for gas to disperse. If problems with burner lighting persist, refer to the TROUBLESHOOTING section of these instructions.
If power is not available, light a match or similar, then turn the gas control knob for the burner to be lit, to the High Flame setting. Once again if problems with burner lighting persist, refer to the TROUBLESHOOTING section of these instructions.
When burner lights, adjust desired flame height. On finishing, turn control knob to off position marked with a black DOT.
10

BURNER AND UTENSIL CHOICE Depending on the hotplate model, the burner choices are: BDG604G(-F): Auxiliary (small), Semi-Rapid x2 (medium), and Wok (triple ring) burners. BDG302WG(-F): Semi-Rapid (medium), Wok (triple ring) BDG301G(-F): Wok (triple ring)

The maximum utensil (pan) diameters in millimetres (mm) for each burner are:

For Natural Gas hotplates
Auxiliary (small) and Semi-Rapid (medium) = 195 mm
Rapid (large) = 230 mm Triple ring (wok) = 270 mm
2. For Universal LPG hotplates Auxiliary (small), Semi-Rapid (medium) and
Rapid (large) = 195 mm Triple ring (wok) = 230 mm

The minimum utensil (pan) diameters in millimetres (mm) for each burner are:
Auxiliary (small) = 80 mm and Semi-Rapid (medium) = 140 mm Rapid (large) and Triple ring (wok) = 195 mm
For best efficiency and to ensure utensil handle does not overheat, place the utensil centrally on the burner and adjust the flame height so all the flame remains under the utensil.

Do not place anything, eg. flame tamer, asbestos mat, between pan and pan support as serious damage to the appliance may result.

Do not remove the pan support and enclose the burner with a wok stand as this will concentrate and deflect heat onto the hotplate.

Do not use large pots or heavy weights which can bend the pan support or deflect flame onto the hotplate.

Locate pan centrally over the burner so that it is stable and does not overhang the appliance.

Use only a wok support supplied or recommended by the manufacturer of the appliance.
NOTE: Enclosure may be circular or square
11

Maintenance & Troubleshooting
Warning: To maintain safe operation, it is highly recommended that this appliance be inspected and serviced every two years by an authorised service person. Cleaning and maintenance should be carried out with the appliance cold especially when cleaning the enameled parts. Avoid leaving alkaline or acid substances(lemon juice, vinegar etc.) on the surfaces.

burner crown (F). Wash down with warm soapy water and rinse with clean water. Dry with a clean soft cloth.
Use a cotton bud, tooth brush, or some other item to clean out any incrustations or dirt from the four holes marked(H)

STAINLESS STEEL The stainless steel hob of the hotplate must be cleaned regularly (e.g. weekly) to ensure long life expectancy of the hotplate. Ensure hotplate has cooled. Wash down with warm soapy water and rinse with clean water. Dry with a clean soft cloth. A specialized stainless steel cleaning fluid may be used. NOTE: Ensure that wiping is done along with the grain of the stainless steel to prevent any unsightly crisscross scratching patterns from appearing.
TRIVETS (UTENSIL SUPPORTS) Enameled parts must only be washed with a sponge and soapy water or with non-abrasive products. Rinse with clean water. Dry with a clean soft cloth.
BURNERS Remove trivets from hob. Ensure burners are cool. Remove the burners enameled cap (C) and aluminum

Replace burners and ensure they are correctly repositioned over the igniter (S) and thermocouple (T). The igniter (S) must be clean for trouble free sparking. Test burner ignition and burner flame for correct operation.
The Triple Ring (Wok) burner (diagrams below) does not fit over the igniter or thermocouple but must be placed on its supports. If burner is placed correctly it will not rotate on its supports.

12

TROUBLESHOOTING
Servicing of the hotplates must only be done by an authorised service representative (see back of this booklet) and the hotplate must not be modified. Power must be disconnected before any servicing or maintenance is conducted.

It is recommended the hotplate serviced by an authorized person at least every 2 years. This service is not covered by warranty. Abnormal conditions include: Excessively yellow or sooting flametype.

Flame lifting off the burner ports.

Flame lighting back into the burner (normally associated with a popping sound).

Objectionable odour of the flames combustion products.

Should a faulty condition develop in the hotplate that is not described above, refer to the following table first for possible causes and remedies prior to contacting an authorised service representative. Servicing beyond the remedies listed shall only be undertaken by an authorised service representative.

FAULT

POSSIBLE CAUSE

No spark when gas control knob depressed.

No power.
Loose sparker cable. Burner not aligned properly.

Burner not lighting when spark ignition working.

Gas supply off. Burner not aligned properly. Burner ports blocked.

Burner goes out when control knob released.
Uneven flame pattern or slight flame lifting. At minimum flame setting the flame is too high.
Small flame on High setting.

Flame safeguard not activated. Flame safeguard faulty connection or broken. Burner ports blocked.
Turndown control setting incorrect. Regulator faulty. Gas supply pressure low. Incorrect injector fitted. Blocked injector or gas supply tube.

REMEDY Check plugged in and switched on. Check mains circuit breaker. Call authorised representative. Remove and re-fit burner. Check gas supply valve on. Remove and re-fit burner. Remove, clean and replace burner. Re-light, allow more time for flame safeguard to activate.
Call authorised representative.
Remove, clean and replace burner.
Call authorised representative.
Call authorised representative. Call authorised representative. Call authorised representative. Call authorised representative.

Flame too high on High setting.

Incorrect utensil size. Regulator faulty. Incorrect injector fitted. Incorrect utensil size.

Refer to operating instructions utensil choice. Call authorised representative. Call authorised representative. Refer to operating instructions utensil choice.

13

WARRANTY

1.1 In this warranty: 1.1.1 Australian Consumer Law means the law as set out in Schedule 2 of the Competition and Consumer Act 2010; 1.1.2 Company means GSM Retail Australia Pty Ltd ABN 53 007 682 475 of 142-144 Fullarton Road, Rose Park SA 5067. Telephone 1300 373 199. Email admin@gsmretailgroup.com 1.1.3 Consumer means a “consumer” as that term is defined in Section 3 of the Australian Consumer Law as the original purchaser of a Bellini product; 1.1.4 Consumer Guarantees means the guarantees under the Australian Consumer Law; 1.1.5 You means the Consumer.

1.2 Nothing in this warranty affects any person’s rights under the Australian Consumer Law. The benefits to any Consumer under this warranty are in addition to the rights and remedies available under any Consumer Guarantees.
1.3 Subject to the other clauses of this warranty, the Company warrants to the Consumer that the Bellini product will be free of manufacturing defects and will perform to the Company’s specifications.
1.4 The benefit of this warranty extends only to the Consumer as original purchaser of a Bellini product which is installed in a domestic household area. The in Home warranty does not apply to Commercial and or industrial usage. Please See 1.7.7 for additional
information
1.5 This warranty commences on the date of purchase of the Bellini product by the Consumer and continues for the benefit only of the Consumer until the expiry of three (3) year (Warranty Period).
1.6 If within the Warranty Period a manufacturing defect is discovered in the Bellini product or it fails to perform to the Company’s specifications as a result of some defect in materials, components or workmanship (Defect) then the Company will, at its option, repair the Bellini product or supply a replacement Bellini product free of charge. A replacement Bellini product may differ from the original product purchased by the Consumer.
1.7 This warranty will not apply to any Bellini product: 1.7.1 Installed by any person other than a qualified tradesperson; or 1.7.2 Subjected to misuse, neglect, negligence or accidental damage; or 1.7.3 Operated in any way contrary to any operating or maintenance instructions;or 1.7.4 Improperly handled, installed or maintained;or 1.7.5 Altered or modified prior to or after installation; or 1.7.6 Damaged directly or indirectly by power surges, electrical storm damage or connection to incorrect power supply

1.7.7

Industrial and or Commercial usage is inclusive of staff areas in office/ shop environments, hotel/ motel or other similar accommodation or rental type properties including Bed and Breakfast establishments.

The Australian Consumer Law requires the inclusion of the following statement with this warranty:
Our goods come with guaranteed that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.

1.8 You must provide proof of your purchase of the Bellini product and the date of purchase in order to obtain the benefit of this warranty.
1.9 If you live outside the service area of the Company or one of its service agents, this warranty does not cover the cost of transport of the Bellini product for service nor the service agent’s traveling costs to and from your home.
1.10 If you are required to transport the Bellini product to the Company or its service agent, you must ensure it is safely disconnected by a qualified tradesman and securely packed and insured. The Company does not accept any responsibility for loss or damage of the Bellini product prior to it being received by the Company or its service agent.
1.11 You will be responsible for all costs of returning a Bellini product to the Company and for redelivery of the Bellini product by the Company (whether it is the original or a repaired and/or a replacement Bellini product) and for any other expenses you incur in claiming under this warranty.
1.12 The Company or its service agent will examine any Bellini product and if the Company determines that it is defective through no fault of the Owner and is otherwise undamaged, the Company will repair or replace the Bellini product in accordance with this warranty.
DO NOT SEND IN THIS WARRANTY Fill out the following details and file with your purchase invoice for safe keeping.
RETAIN & FILE WITH YOUR RECEIPT Your Purchase Receipt/Invoice is proof of date of purchase. If you are unable to establish the date of purchase, or if the fault is not covered by this warranty, or if the product is found to be in working order, you will be required to bear all service call charges. GSM Retail Australia Pty Ltd reserves the right to discontinue items, modify designs and change specifications without incurring obligation. Whilst every effort is made to ensure that descriptions, specifications and other information in this publication is correct, no warranty is given in respect thereof and the company shall not be liable for any errors therein. Purchased from: Co. Name: Address: Date of Purchase:
Serial number: NOTE: Consistent with our continuing product development policy, improvements may have been made which render the contents of this packaging slightly different to that shown.
For Warranty and technical queries: Australia 1300 373 199 : New Zealand 0800 764 912