SONOFF 4CHR3 4 Gang WiFi Smart Switch Instruction Manual

4CHR3 4 Gang WiFi Smart Switch
Instruction Manual Operating Instruction

4CHR3 4 Gang WiFi Smart Switch

Power off **** To avoid electric shocks, please consult the dealer or a qualified professional for help when installing and repairing!

Wiring instruction

Light fixture wiring instruction:
Socket wiring instruction (Don’t need to connect if no ground wire): Make sure all wires are connected correctly.

Download the eWeLink APP

http://app.coolkit.cc/dl.html

Power on

After powering on, the device will enter the quick pairing mode (Touch) during the first use. The Wi-Fi LED indicator changes in a cycle of two short and one long flash and release.
The device will exit the quick pairing mode (Touch) if not paired within 3mins. If you want to enter this mode, please long press any pairing button for about 5s until the Wi-Fi LED indicator changes in a cycle of two short and one long flash and release.

Add the device

Tap “+” and select “Quick Pairing”, then operate following the prompt on the APP.

Compatible Pairing Mode

If you fail to enter Quick Pairing Mode (Touch), please try “Compatible Pairing Mode ” to pair.

1. Long press any pairing button for 5s until the Wi-Fi LED indicator changes in a cycle of two short flashes and one long flash and release. Long press any pairing button for 5s again until the Wi-Fi LED indicator flashes quickly. Then, the device enters Compatible Pairing Mode .
2. Tap “+” and select “ Compatible Pairing Mode ” on APP.
   Select Wi-Fi SSID with ITEAD-** and enter the password 12345678, and then go back to eWeLink APP and tap “Next”. Be patient until pairing completes.

Specifications

4CHPROR3: 100-240V AC 50/60Hz (DC: 9-23V)
Max. Load| 4CHR3: 10A/2200W/Gang 16A/3500W/Total
4CHPROR3: 10A/2200W/Gang 40A/8800W/Total
RF| 433.92MHz
Wi-Fi| IEEE 802.11 b/g/n 2.4GHz
Operating systems| Android & iOS
Working temperature| -10℃~40℃
Material| PC V0
Dimension| 145x90x34mm

4CHR3 does not support the remote controller with 433.92MHz.

Product Introduction

The device weight is less than 1 kg.
The installation height of less than 2 m is recommended.

Wi-Fi LED indicator status instruction

Features

This device is a 4-Gang Wi-Fi smart switch with self-locking, interlock and inching that allow you to remotely turn on/off connected devices via your smartphone, schedule on or off, share to your family to control together. RF Remote Controller Pairing
The 4CHPROR3 supports the remote controller with 433.92MHz frequency brand to turn on/off, and each channel can learn it independently, which is local short- range wireless control not Wi-Fi control.
Pairing Method:
Long press the channel switch button to be paired for 3s until the Wi-Fi LED indicator turns red and “quickly flashes once” and release, then short press the button to be paired on the remote control. If the Wi-Fi LED indicator turns red and “quickly flashes
once”, it indicates that the pairing is successful.
Clearing Method:
Long press the channel switch button to be cleared for 5s until the Wi-Fi LED indicator turns red and “quickly flashes twice” and release, then short press the button to be cleared on the remote control. If the Wi-Fi LED indicator turns red and “quickly flashes once”, it indicates that the code is cleared.

Switch Network

If you need to change the network,Long press the any pairing button for about 5s until the Wi-Fi LED indicator changes in a cycle of two short and one long flash and release, , then the device enters quick pairing mode and you can pair again.

Factory Reset

Deleting the device on the eWeLink app indicates you restore it to factory setting.

Common Problems

Q: Why my device stays “Offline”?
A: The newly added device needs 1 – 2mins to connect Wi-Fi and network. If it stays offline for a long time, please judge these problems by the blue Wi-Fi indicator status:

1. The blue Wi-Fi indicator quickly flashes once per second, which means that the switch failed to connect your Wi-Fi:

2. Maybe you have entered a wrong Wi-Fi password.

3. Maybe there’s too much distance between the switch your router or the environment causes interference, consider getting close to the router. If failed, please add it again.

4. The 5G Wi-Fi network is not supported and only supports the 2.4GHz wireless network.

5. Maybe the MAC address filtering is open. Please turn it off.
   If none of the above methods solved the problem, you can open the mobile datanetwork on your phone to create a Wi-Fi hotspot, then add the device again.

6. Blue indicator quickly flashes twice per second, which means your device has connected to Wi-Fi but failed to connect to the server.
   Ensure steady enough network. If double flash occurs frequently, which means you access an unsteady network, not a product problem. If the network is normal, try to turn off the power to restart the switch.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>