Corbero CCHMP1033N Built In Oven Instruction Manual

Corbero CCHMP1033N Built In Oven

Instruction Manual

The CCHMP1033N and CCHMP1033W Built-in Ovens come with the following manual. Please read it carefully before using the product and keep it for future reference.

PRODUCT SAFETY INFORMATION

Please read all instructions before using this appliance. This book contains valuable information about operation, care, and service. Keep it in a safe place for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance so that the new owner can be acquainted with the functioning of the appliance and relevant warnings.

1. When you use it for the first time, there will be a pungent smell or smoke, which is normal. If it does happen, you should wait for the smell or smoke to disappear before putting food in the oven.

2. Please use the product in an open environment.

3. The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised.

4. If the surface is cracked, switch off the appliance to avoid the possibility of electric shock.

5. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

6. During use, the appliance becomes very hot. Care should be taken to avoid touching heating elements inside the oven.

7. Do not allow children to go near the oven when it is operating, especially when the grill is on.

8. Ensure that the appliance is switched off before replacing the oven lamp to avoid the possibility of electric shock.

9. The means for disconnection must be incorporated in the fixed wiring in accordance with the wiring specifications.

10. Children should be supervised to ensure that they do not play with the appliance.

11. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
    supervision or instruction concerning the use of the appliance by a person responsible for their safety.

12. Accessible parts may become hot during use. Young children should be kept away.

13. An all-pole disconnection means must be incorporated in the fixed wiring in accordance with the wiring rules.

PRODUCT INSTALLATION

The Built-in Oven can be installed in a standing cabinet or a ground cabinet. Please refer to the cabinet diagrams on pages 4-5 for more information. It is important to follow the installation instructions carefully to ensure safe and proper usage of the oven.

Installation Important Instructions

• Ensure that the power supply is turned off before installation.
• Make sure that the oven is installed on a stable surface and leveled.
• Leave enough space around the oven for ventilation.
• Connect the oven to the power supply following the wiring specifications.

Installation steps

Follow these steps to install the Built-in Oven:

1. Choose a suitable location for the oven.

2. Install the oven into the cabinet according to the cabinet
   diagram.

3. Connect the oven to the power supply following the wiring
   specifications.

4. Turn on the power supply and test the oven to ensure it is
   working properly.

PRODUCT INTRODUCTION

Control Panel Introduction
The control panel is located on the front of the oven and consists of various buttons and knobs. Please refer to the user manual for detailed information on how to operate the control panel.

Mode Introduction
The Built-in Oven has several modes that can be used for different cooking needs. Please refer to the user manual for detailed information on each mode and how to use them.

First Use
Before using the Built-in Oven for the first time, it is recommended to run it empty for 30 minutes to remove any manufacturing residues. After that, the oven is ready for use.

Operation Steps
Follow these steps to use the Built-in Oven:

1. Select the desired mode using the control panel.
2. Adjust the temperature and cooking time as per your recipe.
3. Place your food in the oven and close the door.
4. Monitor your food through the oven window or by opening the door occasionally.
5. When your food is cooked, turn off the oven and remove your food.

ACCESSORY

Accessory Included
The Built-in Oven comes with a baking tray, wire rack, and crumb tray.

Accessory Use
The baking tray and wire rack can be used to cook various types of food. The crumb tray should be placed at the bottom of the oven to collect any food debris or crumbs.

PRODUCT CLEANING MAINTENANCE

Cleaning
After each use, it is recommended to clean the oven to maintain its performance and prolong its lifespan. Use a damp cloth to wipe the interior and exterior of the oven. The baking tray and wire rack can be cleaned separately with hot water and soap.

Lamp Replacement
If the oven lamp needs to be replaced, ensure that the appliance is switched off before replacing it to avoid the possibility of electric shock.

product FAULT HANDLING

If the Built-in Oven malfunctions or shows any signs of damage, please contact a qualified technician for repair or replacement.

Product TECHNICAL PARAMETERS

Please refer to the user manual for detailed technical specifications of the Built-in Oven.

PRODUCT RECYCLING

Please dispose of the Built-in Oven responsibly by following your local recycling guidelines. Before using this product, please read this manual carefully and keep it for future reference.

SAFETY INFORMATION

Thank you for choosing us! Please read all instructions before using this appliance. This book contains valuable information about operation, care and service. Keep it in a safe place for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with appliance in order that new owner can be acquaint-ed with the functioning of the appliance and relevant warnings. THESE WARNINGS ARE PROVIDED IN THE INTEREST OF SAFETY. PLEASE READ THEM CAREFULLY BEFORE INSTALLING OR USING THE APPLIANCE. To maintain the EFFICIENCY and SAFETY of this appliance, we recommend:

• Call only the Service Centers authorized by store where you buy the cooker
• Always use original Spare Parts

1. When the oven is first switched on, it may give off an unpleasant smell. This is due to the bonding agent used for the insulat-ing panels within the oven. Please run the new empty product with the conventional cooking function, 250°C, 90 minutes to clean oil impurities inside the cavity.
2. When you use it for the first time, there will be a pungent smell or smoke, which is normal. If it does happen, you should wait for the smell or smoke to disappear before putting food in the oven.
3. Please use the product under an open environment.
4. The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Chil-dren less than 8 years of age shall be kept away unless continu-ously supervised.
5. If the surface is cracked, switch off the appliance to avoid the possibility of electric shock.
6. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
7. During use, the appliance becomes very hot. Care should be taken to avoid touching heating elements inside the oven.
8. Do not allow children to go near the oven when it is operating, especially when the grill is on.
9. Ensure that the appliance is switched off before replacing the oven lamp to avoid the possibility of electric shock.
10. The means for disconnection must be incorporated in the fixed wiring in accordance with the wiring specifications.
11. Children should be supervised to ensure that they do not play with the appliance.
12. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appli-ance by person responsible for their safety.
13. Accessible parts may become hot during use. Young children should be kept away.
14. An all-pole disconnection means must be incorporated in the fixed wiring in accordance with the wiring rules.
15. If the supply cord is damaged, it must be replaced by the man-ufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
16. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in the shattering of the glass.
17. Only use the temperature probe recommended for this oven.
18. A steam cleaner is not to be used.
19. The appliance is not intended to be operated by means of an external timer or a separate remote control system.
20. The instructions for ovens that have shelves shall include de-tails indicating the correct installations of the shelves.
21. Do not use the oven unless you are wearing something on your feet. Do not touch the oven with wet or damp hands or feet.
22. For oven: Oven door should not be opened often during the cooking period.
23. The appliance must be installed by an authorized technician and put into use. The producer is not responsible for any damage that might be caused by defective placement, and installation by unauthorized personnel.
24. When the door or drawer of oven is open do not leave anything on it, or you may unbalance your appliance or break the door.
25. Some parts of appliance may keep its heat for a long time; it is required to wait for it to cool down before touching onto the points that are exposed to the heat directly.
26. If you will not use the appliance for a long time, it is advised to plug it off.

DECLARATION OF COMPLIANCE
When you have unpacked the oven, make sure that it has not been damaged in any way. If you have any doubts at all, do not use it: contact a professionally qualified person. Keep packing materials such as plastic bags, polystyrene, or nails out of the reach of children because these are dangerous to children.

INSTALLATION

1. As the appliance is constantly upgrading, the actual appliance shall prevail if the picture is different from the actual appliance.
2. The thickness of the cabinet board is 20 mm.
3. If the power socket is installed on the back of the appliance, the depth of the cabinet opening shall be increased from a minimum of 590 mm to 620 mm.
4. The dimensions in the figures are in mm.

Cabinet Diagram (Standing Cabinet)

1. Reserve 5 mm for the door panel at the top and bottom respectively.
2. Reserve 20 mm for the door panel on the left and right respectively.
3. Reserve 20 mm for the door panel in thickness.

Cabinet Diagram (Ground Cabinet)

If the appliance is installed under the hob, the minimum thickness of worktop A is shown below:

Installation Important Instructions

Content that means [mandatory]

1. The safe operation of this appliance can only be guaranteed if it has been installed to a professional standard in accordance with these installation instructions. The installer shall be liable for any damage resulting from incorrect installation.
2. The entire installation process requires two professional installers. Wear dry protective gloves during installation to avoid scratches or electric shock.
3. Fitted units must be heat-resistant up to 90°C, and adjacent unit fronts up to 70 °C.
4. Please use a 16A socket.

Content that means [prohibit ]

1. Do not install the appliance behind a decorative door or the door of a kitchen unit, as this may cause the appliance to overheat.
2. Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transit.
3. Do not block the vent of the appliance and the gap between the cabinet and the appliance.
4. Use extreme caution when moving or installing the appliance. It is very heavy, do not lift the appliance by the door handle.
5. If the power cord or power plug is damaged, stop using the appliance immediately, to avoid fire, electric shock or other injuries.

Content that means [note]

1. Be very careful when moving or installing the appliance to avoid damage to the appliance or damage to the cabinets.
2. Before starting up the appliance, remove all packaging materials and accessories from the cavity.
3. The power socket shall be accessible to users (such as next to the cabinet) for easy power-off.
4. After installation is complete, make sure that the power plug is firmly inserted into the socket.
5. Please refer to the “Cabinet Diagram” for the requirements of net depth of the cabinet. The clearance between the cabinet bottom board and the rear board (or wall) shall not be less than 50 mm.

Installation steps

1. Please customize the cabinet according to the “Cabinet Diagram”.
2. Before installation, please check for normal power socket and appropriate grounding, and check whether the cabinet dimension meets the installation requirements.
3. Place the appliance in designated locations in the kitchen, install it in a vertical cabinet, and connect the power supply.
4. To locate the mounting fixing holes, open the appliance door and look at the side frame of the appliance(position shown above).
5. Fix the appliance to the cabinet with two rubber plugs A and screws B provided with the appliance.

INTRODUCTION

When removing food, please wear heat-insulating gloves to prevent burns! At the moment of opening the door of the furnace, pay attention to thesteam. Please open the door at a small Angle to avoid the steam on your face. As the product is constantly upgraded, if there is any difference between the real object and the picture below, please refer to the real object.

Control Panel introduction

Mode introduction

First use
Before using it for the first time, please clean the oven and accessories to a certain extent.

1. Remove the oven packaging shipping protection parts.
2. Remove all accessories (eg: baking trays, grills, foam, etc.) from the cavity.
3. Thoroughly clean the attachment with soapy water and a rag or soft brush. Wipe cavity and oven surfaces with a soft damp cloth.
4. To avoid fire, please make sure that the cavity is free of any remaining packing materials and accessories when using it for the first time.
5. When using it for the first time, keep the kitchen highly ventilated (open the hood and windows). During this time, keep children and pets out of the kitchen and keep the doors of adjacent rooms closed.
6. When used for the first time, the anti-corrosion coating of the oven heating tube evaporates when heated, which will produce a pungent smell or smoke, which is a normal phenomenon. Please run the following mode:

Operation steps

Setting the clock
When the oven is first connected to the electrical supply and powered on, the clock will need to be set.

1. Press the” ” key, the hour digit flashes.
2. Turn knob “K2” to adjust the hour digit.
3. Press the” ” key, the minute digit flashes.
4. Turn knob “K2” to adjust the minute digit.
5. Press the” ” key to complete the clock setting.

Notes:

1. The clock is a 24 hour clock.
2. Before using the oven, please complete the clock setting.
3. During the clock setting process, you can press ” ” key to cancel the current clock setting.
4. If you need to reset the clock, please follow the “Setting the clock” steps in standby mode.

Function setting

1. In standby or reminder state, turn knob “K1” to select the function.
2. Turn knob “K2” to adjust the temperature.
3. Press the ” ” key to start cooking.
4. If you skip step 2, press the ” ” key to start cooking. The default time is 9 hours, and the display screen shows the default temperature.

Notes

1. During cooking, the time can be adjusted by turning the knob “K1″. After adjusting the time, please press the ” ” key within 3 seconds to confirm.
2. During cooking, the temperature can be adjusted by turning the knob “K2″. After adjusting the temperature, please press the ” ” key within 3 seconds to confirm.

Lamp function
Turning on the lamp can better observe the cooking situation of food. If you need to turn off or turn on the lamp, you can follow these steps:

1. Turn knob “k1” to select “ “.
2. Press the ” ” key to confirm.

Reminder function

This function will help to remind you to start cooking in a certain time. Only when oven in standby mode and clock setting, the reminder can be set.

1. Press the “ ” key, and the hour digit flashes.
2. Turn knob “k2” to adjust the hour digit.
3. Press the ” ” key, and the minute digit flashes.
4. Turn knob “K2” to adjust the minute digit.
5. Press the ” ” key to complete the setting, and the icon “ ” is always on, and the countdown starts. After the countdown is completed, the buzzer sounds and the icon ”  ” goes out.

Notes

1. You can cancel the reminder by pressing the “ ” key during setup.
2. After setting the reminder, you can press the ” ” key twice to cancel the reminder.

Inquiring function

1. During cooking process, if the clock has been set, press the “ ” key to check the current time; If the reminder function is set, press the ” ” key to check the reminder time.
2. In reminder state, if the clock is set, press the ” ” key to check the current time.

Start/Pause/Cancel function

1. If the cooking time has been set, press the “ ” key to start cooking. If the cooking is paused, press the ” ” key to continue cooking.
2. During cooking process, press the ” ” key once to pause the cooking. Press the ”  ” key twice to cancel the cooking.

Energy-Saving function

1. In standby or reminder state, press the ” ” key for 3 seconds to turn off the LED display and enter the energy-saving mode.
2. In standby state, If there is no operation in 10 minutes, the LED display will go off and enters the energy-saving mode.
3. In the energy-saving mode, press any key or turn the knob to exit the energy-saving mode.

Child lock function

1. Enter the child lock: Press the ” ” and ” ” keys for 3 seconds at the same time, the buzzer will beep, and the icon “ ” will light up, indicating that the child lock is entered.
2. Release the child lock: Press the “ ” and ”  “keys for 3 seconds at the same time, and the buzzer will beep, indicating that the child lock is released.

Pyrolytic function

This function allows you to clean thoroughly the oven cavity.

1. Turn knob “K1″ to select the pyrolytic function. LED will display ” PyR “.
2. Press the ” ” key to confirm, and the default working time is 2 hours.
3. Turn knob “K1” to adjust the working time. The time can be set 1:30 or 2:00 hours.

Notes

1. When the oven door is not closed, pressing start button will be invalid, LED display ” door “, ” PYR “.
2. When the oven’s center temperature is highter than 320°C, pressing start button will be invalid. The LED will display ” COOL ” and ” PYR “. When the oven’s center temperature is lower than 200°C, press cancel button once, it will pause; press again, it will return to standby state. If highter than 200°C, press cancel button once, it will return to standby state directly.
3. Open the door when the oven is working, the LED will display ” door ” and the buzzer will sound continuously until the door was closed or press cancel button.
4. Before activating the pyrolytic cleaning function, remove any excessive spillage and make sure that oven is empty. Do not leave anything inside it (e.g. pans, baking tray, dripping pan, slider bracket etc.) as this could heavily damage them.
5. When finished pyrolytic cleaning, don’t interrupt the power in an hour.

ACCESSORIES

As the products and accessories are constantly upgraded, if there is any difference between the real object and the picture below, please refer to the real object. Your appliance is accompanied by a range of accessories. Here, you can find an overview of the accessories included and information on how to use them correctly.

Accessories included
Your appliance is equipped with the following accessories:

Accessories use
For the oven to work properly, the grill rack and Baking Tray should only be placed between the first and fifth levels. When used together, place the Baking tray under the grill.

CLEAN AND MAINTENANCE

Cleaning
Disconnect the power supply before cleaning and maintenance. In order to ensure the life of the oven, it should be thoroughly cleaned frequently. Cleaning steps are as follows:

1. After cooking is complete, wait for the oven to cool down completely. Remove oven accessories, rinse with warm water and dry.
2. Use a hot rag to clean food residue or grease from the oven.
3. Clean the oven surface with a soft cloth dampened with detergent and dry.

Notes

1. Do not use sharp cleaning tools, hard brush,es and corrosive cleaning products, so as not to damage the oven and its accessories.
2. Do not use a rough scrubbing agent or sharp metal spatula to clean the door glass.

Lamp Replacement

1. Switch off and disconnect the power from the oven. Ensure that the internal parts are cool before touching internal parts.
2. Remove the lamp cover by turning it counter-clockwise (note, it may be stiff), replace the bulb with a new one of the same type.
3. Insert the new bulb, which should be resistant to 300°C. For replacement bulbs contact your local service centre.
4. Re-fit the cover.
5. If in any doubt, consult a qualified electrician for help.

WARNING:
To avoid electric shocks-please ensure that the electricity supply to the appliance is switched off and the appliance is fully cold. before removing the lamp lens.

FAULT HANDLING

If the problem cannot be solved or other problems occur, please contact the after-sales service.

After cooking, the machine still has the sound of working (the sound of the fan rotating).| Fan delay blowing, used for heat dissipation.| Under normal conditions, food can be taken out normally without treatment;Do not unplug the fan while it is in operation.
There is a sound in the oven cavity when the oven is working.| 1.  The sound of a cavity expanding by heat and contracting by cold.

2.   The furnace cavity is not cleaned for a long time, which accumulates a lot of grease.

| 1.  Belong to normal condition, need not deal with.

2.   Wipe the heating tube and furnace cavity with a clean towel.

The first use has an unpleasant smell.| Heating tube with anticorrosive coating, heating after melting smell.| For the first use, please heat the cavity in a well-ventilated environment for half an hour.
The machine was smoking.|

1. Product failure damage.

2.   The furnace cavity has oil, food residue, etc., not cleaned in time.

| 1.  Turn off the power and seek after service.

2.   Wipe the heating tube and furnace cavity with a clean towel

The food is not cooked.| 1. The heating time is too short.

2.   Oversized portions of food.

| 1.  Prolong the heating time appropriately.

2.   Break the food into small pieces or cook it multiple times.

Furnace light not on.| The furnace lamp is broken.| Please seek after service.

PRODUCT RECYCLING

This symbol on the product or instruction manual indicates that your device should be disposed of separately from your household waste at the end of its useful life. There is a separate recycling system locally for recycling. For more information, please contact the local authority or retailer where you purchased the product. When you have unpacked the oven, make sure that it has not been damaged in any way. If you have any doubts at all, do not use it: contact a professionally qualified person. Keep packing materials such as plastic bags, polys tyren, or nails out of the reach of children because these are dangerous to children.

CERTIFICATE OF GUARANTEE

The presentation of the purchase invoice accompanied by this guarantee certificate is essential.

Covered Risks.
This appliance is guaranteed against any malfunction, provided that it is intended for domestic use, proceeding to its repair within the warranty period and only by the authorized SAT network.

Warranty Exceptions

• That the date of the certificate does not coincide with the date of sale of the original invoice.

• Faults produced by blow, by fall or any other cause of force majeure.

• If the device has been manipulated by unauthorized personnel.

• Faults produced or derived as a consequence of improper use, installation defects, or modifications to the device that alter its operation.

• Start-up, maintenance, cleaning, components subject to wear, lamps, aesthetic parts, oxidation, plastics, rubbers, housings and crystals.

• Microwave ovens (with the exception of built-in ones) and tabletop ovens in the event of any incident of
  operation, they must be taken to the nearest technical service by the customer. They are not collected or repaired at home.

• Electric thermos guarantee. 3-year warranty including travel and labor costs that correspond to the repair of the product, having to have maintenance once every 12 months. Especially if you have installed a gas appliance, keep in mind as the owner of the installation, the obligation to carry out a complete review of the equipment, (according to Royal Decree 238 / 2013, of April 5. RITE. IT3, M. Lo thermos electrical and boilers that include hot water storage tanks, for the benefit of the Guarantee to apply, it is mandatory that the magnesium anode is operational and that it performs the protection function adequately.For this, it is recommended that the anode be checked biannually by the Official Service and is renewed when necessary Periodicity that must be annual in those areas with critical waters (CaCO3 content greater than 200mg/L, that is, from 20ºfH of hardness) Deposits without the correct state of the protection anode are not covered by the warranty Regardless of the type of tank or product, all heating or DHW overpressure valves must be channeled to avoid damage and n the house due to water discharges. The product warranty does not cover damages caused by not channeling the water spilled by this valve.

“THESE EXCEPTIONS VOID THE WARRANTY, THE REPAIR BEING CHARGED TO THE CUSTOMER”
Period covered in devices according to the law of guarantees in the sale of consumer goods Current law is “RD 7/2021”

• Official Technical Service: 911 08 08 08

Hours of operation Monday to Friday from9h00 a 19h00. Telephone contact 911 08 08 08 Contact email info@corbero.es web_ www.corbero.es Official Technical Service Address_Vidal i Ribes 8-10 08950 Esplugues de Llobregat Barcelona

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>