Bellini BRA52UX 52cm and 75cm Undermount Rangehood User Manual

Bellini BRA52UX 52cm and 75cm Undermount Rangehood User Manual

52cm & 75cm Undermount Rangehood

Model No.
BRA52UX – FINELINE: 81476
BRA52UX-F
BRA75UX – FINELINE: 133506
BRA75UX-F

V9 January 2023

Thank you.

Thank you for choosing Bellini Appliances.
This Bellini appliance carry a 3 year in home warranty, be sure to retain your user manual and receipt.

For all warranty and technical queries please phone:

Australia 1300 373 199

New Zealand 0800 764 912

GSM Retail Australia Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: Australia 1300 373 199
For Warranty and technical queries: New Zealand 0800 764 912
www.belliniappliances.com.au

Safety Instructions

This manual explains the proper installation and use of your rangehood, please read it carefully before using even if you are familiar with the product. The manual should be kept in a safe place for future reference.

Never to do:

• Do not try to use the rangehood without the grease filters or if the filters are excessively greasy!

• Do not install above a cooktop with a high level grill.

• Do not leave frying pans unattended during use because overheated fats or oils might catch fire.

• Never leave naked flames under the rangehood.

• If the rangehood is damaged, do not attempt to use.

• Do not flambé under the rangehood.

• CAUTION: Accessible parts may become hot when used with cooking appliances.

• The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the rangehood. (When the rangehood is located above a gas appliance, this distance shall be at least 65 cm)

• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.

Always to do:

• Important! Always switch off the electricity supply at the mains during installation and maintenance such as light bulb replacement.

• The rangehood must be installed in accordance with the installation instructions and all measurements followed.

• All installation work must be carried out by a competent person or qualified electrician.

• Please dispose of the packing material carefully. Children are vulnerable to it.

• Pay attention to the sharp edges inside the rangehood especially during installation and cleaning.

• Make sure the ducting has no bends sharper than 90 degrees as this will reduce the efficiency of therangehood.

• Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

• Warning: Before obtaining access to terminals, all supply circuits must be disconnected.

• Always put lids on pots and pans when cooking on a gas cooker.

• When in extraction mode, air in the room is being removed by the rangehood. Please make sure that proper ventilation measures are being observed. The rangehood removes odours from room but not steam.

• Rangehood is for domestic use only.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• Caution: The appliance and its accessible parts can become hot during operation. Be careful to avoid touching the heating elements. Children younger than 8 years old should stay away unless they are under permanent supervision.

• There shall be adequate ventilation of the room when the rangehood is used at the same time as appliances burning gas or other fuels.

• There is a fire risk if cleaning is not carried out in accordance with the instructions.

• Regulations concerning the discharge of air have to be fulfilled.

• Clean your appliance periodically by following the method given in the chapter MAINTENANCE.

• For safety reason, please use onlv the same size of fixing or mounting screw which are recommended in this instruction manual.

• Regarding the details about the method and frequency of cleaning, please refer to maintenance and cleaning section in the instruction manual.

• Cleaning and user maintenance shall not be made by children without supervision.

• When the range hood and appliances supplied with energy other than electricity are simultaneously in operation, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar).

• WARNING: Danger of fire: do not store items on the cooking surfaces.

• A steam cleaner is not to be used.

• NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.

Product Description

Installation (Vent Outside)

MOUNTING OF THE V-FLAP

If the rangehood does not have an assembled V-flap 1, you should mount the half-parts to its body.The images only show an example of how to mount the V-flap, because the outlet may vary according to different models and configurations.

To mount the V-flap 1 you should:

• Mount two half-parts 2 into the body 6
• the pin 3 should be top oriented;
• the axis 4 should be inserted into the holes 5 on the body;
• repeat all the operations for the 2nd half-part

Installation

If you have an outlet to the outside, your rangehood can be connected as below picture by means of an extraction duct (enamel, aluminum, flexible pipe or non-flammable material with an interior diameter of 150mm)

1. Before installation ensure that the cupboard is structurally sound and is capable of carrying the weight of the rangehood and that the rangehood distance between a cooktop and underneath the rangehood must be minimum of 600mm to a cooktop and a maximum height of 750mm.
   
   *If the instructions of the hob specify a greater distance than the minimum above, then that shall be the minimum height for installation

2. The minimum requirement for the height of the inside cupboard is suggested 384mm to fit the undermount rangehood. Make sure the distance between the edge of the cut out hole and the back of the cupboard is at least 25mm and at least 25mm from the other cut out edges front and sides. The cut out hole in the cabinet should measure Widthdepth 490265 (mm) for BRA52UX and715*265 (mm) for model BRA75UX. Refer pic below.
   

3. Remove the aluminum filter and then use a screwdriver to remove the two screws on the panel. Pry out the lamp terminal box with flat screwdriver and unplug the lamp terminal. Finally, remove the panel.

4. Mount the rangehood on the cabinet with 8 screws (ST4 x 18mm).Then connect the lamp terminal and cover it with lamp terminal box.

5. Secure the front panel on the rangehood body with 2 screws (M4 x 10mm). Reinstall the aluminum filter in the rangehood.
   

Note:The expansion pipe is not included in the product.

WARNING:

• For safety reason, please use only the same size of fixing or mounting screws which are recommended in this instruction manual.
• Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

Start Using Your Rangehood

Toggle switch

There are 3 speeds for the motor and on/ off switch for the lamp
1.Lamp – Turn on/off light
“0” – to switch off light
“I” – to switch on light

2 .Speed – select speed to suit cooking conditions
“0” – to switch off motor
Low( I ) – light frying/boiling
Medium( II ) – frying/wok cooking/heavy boiling
High ( III ) – grilling, intensive frying and wok cooking

Troubleshooting

NOTE:

Any electrical repairs to this appliance must conform to your local, state and federal laws. Please contact the service centre if in any doubt before undertaking any of the above. Always disconnect the unit from the power source when opening the unit.

Maintenance and Cleaning

Caution:

• Before maintenance or cleaning is carried out, the rangehood should be disconnected from the mains power supply. Ensure that the rangehood is switched off at the wall socket and the plug removed.
• External surfaces are susceptible to scratches and abrasions, so please follow the cleaning instructions to ensure the best possible result is achieved without damage.

GENERAL

Cleaning and maintenance should be carried out with the appliance cold especially when cleaning.
Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.) on the surfaces.

STAINLESS STEEL

The stainless steel must be cleaned regularly (e.g.weekly) to ensure a long life expectancy. Dry with a clean soft cloth. A specialized stainless steel cleaning fluid may be used.

NOTE:

Ensure that wiping is done along with the grain of the stainless steel to prevent any unsightly crisscross scratching patterns from appearing.

CONTROL PANEL SURFACE

The inlay control panel can be cleaned using warm soapy water. Ensure the cloth is clean and well wrung before cleaning. Use a dry soft cloth to remove any excess moisture left after cleaning.

Important
Using neutral detergents and avoid using harsh cleaning chemicals, strong household detergents or products containing abrasives,as this will affect the appearance of the appliance and potentially remove any printing of artwork on the control panel and will void manufactures warranty.

GREASE MESH FILTERS

The mesh filters can be cleaned by hand. Soak them for about 3 minute in water with a mild detergent and then brush it gently with a soft brush. Please do not apply too much pressure so as to avoid any damage to it. (Leave to dry naturally out of direct sun light). Filters should be washed separately to crockery and kitchen utensils. It is advisable not to use rinse aid.

INSTALLING GREASE MESH FILTERS

• To install filters for the following four steps:
  – Angle the filter into the slots at the back of the hood.
  – Push the button on the handle of the filter.
  – Release the handle once the filter fits into a resting position.
  – Repeat to install all filters.

CARBON FILTER-not included in the product

Activated carbon filter can be used to trap odors. Normally the activated carbon filter should be changed every 3 to 6 months according to your cooking habits. The installation procedure of activated carbon filter is as below.

1. Before installing or replacing the carbon filters, please disconnect mains power to the unit.
2. Press the filter lock and remove the mesh filter.
3. Turn the carbon filter on bothsides of the motor anti-clockwise. Replace the carbon filters with the new carbon filters.
4. Place the mesh filter.
5. Connect the power supply to the wall socket.

NOTE:

• Make sure the filter is securely locked. Otherwise, it would loosen and cause danger.
• When activated carbon filter attached, the suction power will be lowered.

BULB REPLACEMENT

Important :

• The bulb must be replaced by themanufacturer, its service agent or similarly qualified persons.
• Always switch off the electricity supply before carrying out any operations on the appliance. When handling bulb, make sure it has completely cooled down before any direct contact with hands.
• When handling bulbs hold with a cloth or gloves to ensure perspiration does not comein contact with the bulb as this can reduce the life of the bulb.

Note:

• Before changing the lights, make sure that the appliance is turned off and unplugged .
• Protect against danger when changing lights, such as wearing gloves.

Changing the lights:

• Remove the grease filter.
• Put one hand into the cavity togently push out the LED light, and use the other hand to grab the light and pull it out, and then pull out the light cable.
• After changing the lamp, plug in thelamp cable, and press the lamp into the lamp hole.
  • ILCOS D code for this lamp is: DBR-2/65-H-64
    – LED modules –round lamp
    – Max wattage: 2×2 W
    – Voltage range: AC 110-240V
    – Dimensions: 64mm

Environment Protection

This product is marked with the symbol on the selective sorting of waste electronic equipment. This means that this product must not be disposed of with household waste but must be supported by a system of selective collection in accordance with Directive 2012/19/EU. It will then be recycled or dismantled to minimize impacts on the environment, electrical and electronic products are potentially dangerous for the environment and human health due to the presence of hazardous substances.For more information, please contact your local or regional authorities.

NOTE:

The following shows how to reduce total environmental impact (e.g. energy use) of the cooking process).

1. Install the rangehood in a proper place where there is efficient ventilation.
2. Clean the rangehood regularly so as not to block the airway.
3. Remember to switch off the rangehood light after cooking.
4. Remember to switch off the rangehood after cooking.

ININFORMATION FOR DISMANTLING

Do not dismantle the appliance in a way which is not shown in the user manual. The appliance could not be dismantled by user. At the end of life, the appliance should not be disposed of with household waste. Check with your Local Authority or retainer for recycling advice.

References

• Bellini - Bellini Website

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>