Babevy CO-P920-1 5 In 1 Pack and Play Baby Bedside Sleeper User Manual

Babevy CO-P920-1 5 In 1 Pack and Play Baby Bedside Sleeper

Specifications

• Product Name: Baby Playard CO-P920-1
• Parts List:
  • 01 – How to set up the bassinet (QTY 1)
  • 02 – Mattress (QTY 6)
  • 03 – Mattress support bars (QTY 2)
  • 04 – Adjustable plastic connectors (QTY 2)
  • 05 – Long rail lock button (QTY 2)
  • 06 – Bottom fixed buckles (QTY 2)
  • 07 – Legs (QTY 2)
  • 08 – Short rail lock button (QTY 2)
  • 09 – Wheels (QTY 1)
  • 10 – Music and toys (QTY 1)
  • 11 – Diaper changing table (QTY 1)
  • 12 – Storage bag (QTY 1)
  • 13 – Carry bag (QTY 1)
  • 14 – Anchor plate and strap (QTY 2)
  • 15 – Rocking bar (QTY 1)

Assembly Instructions

How to set up the bassinet

WARNING: Please follow the instructions step by step. Do not push down the center bottom base until all top bars are locked and rigid.

STEP 1:
Remove product from carry bag and undo the Velcro straps of mattress.

STEP 2:
While keeping the bassinet bottom base high, pull up the short bars in a quick upward motion to lock into place. Note: There are two unlocking mechanisms on each bar, please try to pull it quickly and avoid grabbing the center unlocking mechanisms.

STEP 3:
While keeping the bassinet bottom base high, pull up the long bars in a quick upward motion to lock into place.

Note: If a top bar does not lock into place, pull the base higher and try again.

STEP 4:
After four top bars are locked and rigid, reach through the access hole on sleeping nest bottom and gently push down the bottom base until it is locked.

STEP 5:
Zip up the second sleeping layer, install six mattress support bars into fabric tunnels on the second sleeping layer.

STEP 6:
Lay mattress on second sleeping layer. If a gap is visible on either side of the mattress after installing, reposition the mattress. There are Velcro behind the mattress and the second sleeping layer that can be used to fix the mattress.

STEP 7:

Insert two holding bars and connect two locker bars with holding bars.

How to use the changing table
Connect the changing table on the bassinet bars and push down to lock. Please make sure that the buckle is installed when the baby is lying on the changing table. Assemble the straps as shown, and adjust the length of the straps according to the size of the baby.

STEP 8:
Assemble five parts as shown in the picture and place them on the bassinet.

How to use the rocking bar

STEP 9:
Fix the plastic grip with the bottom tube. See picture 1 and 2.

Rock the bars from the left and right sides.

When the rocking bar is pushed inside, the rocking function stops.

WARNING:

Operating Instructions

How to use as Co-sleeping bassinet

5-position height adjustment:

Highest Position

Second Position

Lowest Position

Find the RED locking button 1 under the plastic connectors on the left and right sides, press the button 1 then pull up button 2 of both sides at the same time, then push down the top rail to lower position. Note: The left and right side plastic connector pieces must be slid down at the same time, so that the top rail can be lowered smoothly.

When set to the lowest position, you can pull out buckles of mattress support- straps from the pockets. Pull the strap up and over the lowering rail and connect it on the front of the lowering rail.

NOTE: The strap is only for lowest position security.

Assemble the buckle as shown in the picture and adjust the length of the strap according to the size of the adult bed.

FAQ

Q: How many parts are included in the Baby Playard CO-P920-1?
A: There are 14 parts included in the Baby Playard CO-P920-1.

Q: How do I set up the bassinet?
A: Follow the steps below to set up the bassinet:

1. Remove the product from the carry bag and undo the Velcro straps of the mattress.
2. While keeping the bassinet bottom base high, pull up the short bars in a quick upward motion to lock them into place.
3. Repeat the same step for the long bars.
4. Once all top bars are locked and rigid, gently push down the bottom base until it is locked.
5. Zip up the second sleeping layer and install six mattress support bars into the fabric tunnels.
6. Lay the mattress on the second sleeping layer and adjust its position if needed.
7. Insert two holding bars and connect two locker bars with holding bars.

Q: How do I use the changing table?
A: To use the changing table:

1. Connect the changing table on the bassinet bars and push it down to lock.
2. Make sure to install the buckle when the baby is lying on the changing table.
3. Assemble the straps as shown and adjust their length according to the size of the baby.

Q: How do I use the rocking bar?
A: Follow these steps to use the rocking bar:

1. Fix the plastic grip with the bottom tube.
2. Rock the bars from the left and right sides.
3. The rocking function stops when the rocking bar is pushed inside.

Parts List

Assembly instructions

How to set up the bassinet

WARNING: Please follow the instructions step by step. Do not push down the center bottom base until all top bars are locked and rigid.

STEP 1
Remove product from carry bag and undo the Velcro straps of mattress.

STEP 2
While keeping the bassinet bottom base high, pull up the short bars in a quick upward motion to lock into place.
Note: There are two unlocking mechanisms on each bar, please try to pull it quickly and avoid to grab the center unlocking mechanisms.

STEP 3
While keeping the bassinet bottom base high, pull up the long bars in a quick upward motion to lock into place.
Note: If a top bar does not lock into place, pull the base higher and try again.

STEP 4
After four top bars are locked and rigid, reach through the access hole on sleeping nest bottom and gently push down the bottom base until it is locked.

STEP 5
Zip up the second sleeping layer, install six mattress support bars into fabric tunnels on the second sleeping layer.

STEP 6
Lay mattress on second sleeping layer. If a gap is visible on either side of the mattress after installing, reposition the mattress. There are Velcro behind the mattress and the second sleeping layer that can be used to fix the mattress.

STEP 7

1. Insert two holding bars.
2. Connect two locker bars with holding bars.

How to use the changing table
Connect the changing table on the bassinet bars and push down to lock.
Please make sure that the buckle is installed when the baby is lying on the changing table.
Assemble the straps as shown,and adjust the length of the straps according to the size of the baby.

STEP 8
Assemble five parts as picture and placed on the bassinet.

How to use the rocking bar

STEP 9
Fix the plastic grip with the bottom tube, see picture 1 and 2.

1. Rocking the bars from left and right sides.
2. When rocking bar pushed inside way, rocking function stop.

WARNING

Possible entanglement or strangulation injury. Keep out of baby’s reach. Remove toy when baby begins to push up on hands and knees. Recommended use from birth to 5 months.
This toy is not intended to be “mouthed” by the baby and should be positioned clearly out of reach of the baby’s face and mouth.
On cribs with adjustable mattress levels, the highest position may allow the toy to be too close to the baby. The second or lower position is more appropriate.
The drop side of the crib should never be lowered with the toy in place and the baby left unattended.
Always attach all provided fasteners (strings, straps,clamps, etc.) tightly to a crib or playpen according to the instructions. Check frequently.
Do not add additional strings or straps to attach to a crib or playpen.

Operating Instructions

How to use as Co-sleeping bassinet 5-position height adjustment

Find the RED locking button 1 under the plastic connectors on the left and right sides, press the button 1 then pull up button 2 of the both sides at the same time, then push down the top rail to lower position.

Note: The left and right side plastic connector pieces must be slid down at the same time, so that the top rail can be lowered smoothly.

When set to the lowest position, you can pull out buckles of mattress support- straps from the pockets. Pull strap up and over lowering rail and connect on front of lowering rail.

NOTE: The strap only for lowest position security.

Assemble the buckle as shown in the picture and adjust the length of the strap according to the size of the adult bed.

WARNING
The attachment system must ALWAYS be used in bedside sleeper mode.

Mattress, Box springs & Frame aligned

• ACCEPTABLE ADULT BED CONDITIONS FOR Co SL EEPING MODE (BEDFRAME IN-LINE)
• UNACCEPTABLE ADULT BED CONDITIONS FOR Co SLEEPING MODE (BEDFRAME NOT IN-LINE)

Not suitable for use next to water beds or children’s beds.

How to use as Baby Playard
Take out the mattress, remove the mattress support bar and the second sleeping layer, and then place the mattress on the bottom layer.

How to fold the bassinet

STEP 1
Remove mattress support bars and mattress, and set aside. Reach through the hole of sleeping nest floor to the red release strap, pull up to collapse the bassinet.

STEP 2
Unlock short top rails by raising center base slightly, push on button of rail locks 1 and lower top rails. Repeat steps on top rails on the long sides.

STEP 3
Lift up the bassinet and adjust the corner posts together until the corner posts are straight up and down, and top corner brackets contact each other.

STEP 4
Wrap the mattress around the unit. There are Velcro straps that feed through plastic loops attached to the backside of the mattress. Pull taut.
NOTE: Do not cover the top corner plastic brackets inside the mattress, do as shown.

STEP 5
Put into carry bag.

WARNING

Failure to follow these warnings and the instructions could result in serious injury or death.
Read all instructions before assembling and using the product.

SUFFOCATI ON HAZARD
Discard all packing materials immediately after opening. Plastic bags and ties may cause suffocation or choking.

Infants have suffocated

• In gaps between extra padding and side of the bassinet, and
• On soft bedding
  Use only the pad provided by manufacturer. NEVER add a pillow, comforter, or another mattress for padding.
  The side rails can only be lowered when the bassinet in bedside sleeper mode. Please keep the side rails on top position while in bassinet and play yard mode.

WARNING

• HORIZONTAL RAIL installed in the upper most position, unless securely attached to the adult bed. Always check to be sure that the upper locking bars and the lower locking bars are in their “locked position” before placing the infant in the bedside bassinet.
  To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by your physician.

• FALL HAZARD-Always check that the bassinet is securely locked on the base/stand pulling upwards on the bassinet bed.
  Do not place any cord, strap or similar item in or near this accessory that could become wrapped around a child’s neck.
  If a sheet is used with the pad, use only the one provided by the bassinet or cradle manufacturer or one specifically designed to fit the dimension of the bassinet or cradle mattress.

• WARNING This beside sleeper is designed for use only with adult beds that are between 19 and 24 inches from floor to top of adult mattress.

• WARNING To avoid death from the infant’s neck being caught on the top rail on the side that is next to the adult bed, the top rail must be no higher than the adult bed mattress.

FALL HAZARD -To help prevent falls, do not use this product when the infant begins to push up on hands and knees or has reached manufacturer’s recommended maximum weight of 19.8lbs(9kg), whichever comes first.
Strings can cause strangulation! Do not place items with a string around a child’s neck, such as hood strings or pacifier cords. Do not suspend strings over a bassinet or cradle, or attach strings to toys.

WARNING
Entrapment Hazard- To prevent death from entrapment, beside sleeper must be properly secured to adult bed using the attachment system.

1. There must be no more than 0.5 in.(13mm) gap between beside sleeper and adult bed.
2. Check tightness before each use by pulling beside sleeper in a direction away from adult bed.
3. If gap exceeds 0.5 in.(13mm), DO NOT use product. Do not fill the gap with pillows, blankets or other items that are suffocation hazards.

WARNING
Always use ALL required parts for each use mode. Check instruction manual for a list of required parts. Periodically check product for loose, damaged or missing parts.

• Always read and follow assembly instructions for each product use mode (bedside sleeper, bassinet, playard).
• DO NOT use bedside sleeper if any parts are missing, damaged, or broken. Contact manufacturer for replacement parts and instructional literature if needed. DO NOT substitute parts.
• Keep instructions for future use.
• Assemble product according to manufacturer’s instructions for ANY use mode-bedside sleeper as well as the bassinet or play yard modes, or both.
• A bedside sleeper is designed to provide a sleeping area for an infant until he or she begins to push up on hands and knees or approximately 5 months of age. Move your child to another sleeping product when your child reaches this stage.

A WARNING-NEVER LEAVE INFANT IN PRODUCT WITH SIDES DOWN.
Infant may roll into space between pad and loose mesh side causing suffocation.

Failure to follow these warnings and the instructions could result in serious injury or death. The product, including side rails, must be fully erected prior to use. Strings can cause strangulation! Never place items with a string around a child’s neck such as hood strings or pacifier cords. Never suspend strings over product or attach strings to toys. Discontinue use of the product when child is able to climb out or reaches the height of 35 in.(890mm). Child can become entrapped and die when improvised netting or covers are placed on top of product. Never add such items to confine child in product. When child is able to pull to standing position, remove bumper pads, large toys, and other objects that could serve as steps for climbing out. Never place product near a window where cords from blinds or drapes can strangle a child. Use ONLY mattress/pad provided by manufacturer (which must be at least 46in. long by 22.8in. wide and not more than 0.59in.thick). Always provide the supervision necessary for the continued safety of your child. When used for playing, never leave child unattended. To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless otherwise advised by your physician.

WARNING
Never leave child in product with side lowered, be sure side is in raised and locked position whenever child is in product.
Never use plastic shipping bags or other plastic film as mattress cover not sold and intended for that purpose. They can cause suffocation.
Never use a water mattress with this product.

• WARNING
  FALL HAZARD: Children have suffered serious injuries after falling from changing tables. Falls can happen quickly.

• STAY in arm’s reach of your child.

• ALWAYS secure this product to the support frame (manufacturer’s instructions for securing the changing table accessory).

• SUFFOCATION HAZARD: Babies have suffocated while sleeping in changing areas. Changing areas are not designed for safe sleeping.

• NEVER allow baby to sleep in changing area.
  Do not use changing table for a child who has reached the height of 22in. (558mm), weight of 15lbs. (6.8kg) or 3 months old, whichever comes first.

• Never use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact us for replacement parts. Never substitute parts.

• Statement describing the hazard.
  Never leave the changing table in place when child is in non-full size crib/play yard. Statement describing the hazard.
  Never leave the second layer in place when child is in non-full size crib/play yard. Read all instruction before use of the changing table.
  Do not use the changing table if it is damaged or broken.

Care & Cleaning

Spot clean with soft clean damp cloth.

• Toy bar and music box: Wipe clean with a damp cloth and mild soap. Air dry. Don’t immerse in water.
• Dolls: Hand wash, air dry.
• Frame:Wipe the metal frame with soft, clean cloth and mild soap.

With your inspiring rating, Babevy will be more consistent to offer you EASY SHOPPING EXPERIENCE, GOOD PRODUCTS and EFFICIENT SERVICE!

Email: support@babevy.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>