W HLER TD 100 Thermal Fast Printer Instruction Manual

: June 15, 2024
: W HLER

W HLER TD 100 Thermal Fast Printer Instruction Manual

General Information

Operation Manual Information

This operation manual allows you to work safely with the Wöhler TD 100 Thermometer. Please keep this manual for your information.
The Wöhler TD 100 Thermometer should be employed by professionals for its intended use only. Liability is void for any damages caused by not following this manual.

Notes

WARNING!
Not following this warning can cause injury or death.

ATTENTION!
Not following this note can cause permanent damage to the device.

NOTE!
Useful information

Intended Use

The Wheeler TD 100 Thermometer allows the user to obtain a hard copy of information held on their measuring device by utilizing the infrared communication.

Components

Device	Components
Wöhler TD 100	Thermometer

1 paper roll
4 x 1.5 AAA size battery

Information on disposal

Electronic equipment does not belong into domestic waste, but must be disposed in accordance with the applicable statutory provisions. You may hand in any defective batteries taken out of the unit to our company as well as to recycling places of public disposal systems or to selling points of new batteries or storage batteries.

Direction

Wöhler Technik GmbH
Wöhler-Platz 1
33181 Bad Wünnenberg
Tel.: +49 2953 73-100
Fax: +49 2953 73-250
E-Mail: info@woehler.com

Technical Data

Description	Data
Paper	Thermopaper
Interface	IR
Batteries	4 batteries 1,5 V type AA
Current Consumption	Online: typ. 1,5 A, Sleep: typ. 26 mA Power off: < 5 μA
Operating Tempera- ture	0 °C to 50°C
Rel. Humidity	10 % to 80 %, non condensing
Dimensions	150 mm x 80 mmx 45 mm
Weight	ca. 420 g with paper

Component explanation

Fig. 1 Overview

Front view

POWER button with LED
green shining: Printer is online
green flashing: The printer is receiving data
red flashing: Battery empty
red blinking. Battery flashing or overheating
Paper load
IR interface
Paper compartment cover
Side view
Lever to open the paper compartment
Bottom
Magnet for fixing the printer
Identification label
Snap closure for the battery compartment
Cover of the battery compartment

Indications

WARNING!
Depending on the use, the print head may be hot. Do not touch the print head! Danger of burning! Do not bring temperature sensitive objects near to the print head.

ATTENTION!
A secure operation will not be possible, if the printer case is damaged or water has penetrated.

Getting started

Batteries

Fig. 4: Bottom of the printer

NOTE!
Only use alkaline batteries with the printer. If zinccarbon batteries are used, the printer may switch off unintentionally.

Open the battery compartment at the bottom of the printer by pulling the lever (8) and removing the battery cover (9) at the same time.

NOTE!
Pull the lever strongly. The safe closure guaranties that the battery compartment will not open accidentally

Insert 4 AA batteries. Observe the polarity indicated on the bottom of the battery compartment.

NOTE!
Remove the batteries, if you intend not to use the printer for a certain time.

NOTE!
When the battery voltage gets too low to support the printing, the red LED light blinks. In this case change the four batteries.

Paper load

Fig. 2: Paper compartment open

Open the paper compartment by pulling down the lever at the right side of the printer (Fig. 1, part 5).
Put the cover of the paper compartment in a vertical position (Fig. 1, part 4).
Insert the paper roll as indicated in the bottom of the paper compartment.
Pull the end of the paper roll out of the paper compartment and close the cover.

Self test

NOTE!
The cover must audibly engage.

Hold down the FEED PAPER button (▲) and then press the POWER button.

The printer will run a self test and print out all fonts, the audio sleep status, the serial number (SN) and the firmware version, battery voltage

Operation

Power on and off

Press the POWER button to turn the printer on and off. The POWER button shines green when the power is on.

Receiving data and printing

You can now start to send the data from the measurement instrument to the printer. Place the printer with the IR receiver (3) toward the transmitting instrument.

NOTE!
The distance between the transmitting instrument and the printer should be 0,30 m approx. and the angle should not exceed ± 15°. Take care that there is no object between the printer and the transmitting instrument.

Feed paper

When the printer is switched on, press the FEED PAPER button (▲) to feed the paper.
For continuously feeding paper, just hold down the FEED PAPER button (▲).

Tearing off the paper

Tear off the paper carefully from the left to the right.

Auto power off

The printer turns off automatically after 10 minutes inactivity.
The auto sleep default is ON.
To switch off or activate again this function, hold down “POWER” button for around 3 seconds while power is on.

In the mean time, it prints out the status.

Troubleshooting

Problem	Possible reason	Solution
The red LED (3) is flashing or shining.	Battery voltage is too low.	Insert

new batteries.
The temperature of the printer is too high.| Switch off the printer until it has cooled down to a nor- mal temperature.
The printer seems to print, the paper is fed forward but without lettering.| The paper is inserted back to front. Only one side can be printed.| Insert the paper correctly. The thermosensitive side of the paper is outside.
The printer cannot be switched on.| There are no batteries or batteries are empty.| Insert new batteries.
After starting the printer, the LED only blinks shortly.| — Batteries are empty or of bad quality.| Insert high quality batteries.
The battery feed operates correctly, but the self test not.
The printer only prints a few letters in a line.
The printer prints bars instead of letters.|

Information is lost be- cause the printer cannot print fast enough to keep up with the incoming data.
The printer has detected incorrect data due to inter- ference with or interruption to the incoming information.Common causes for this error includeincorrect positioning of the printer with reference to the instrument (distance or angle of operation),obstruction of the infrared signal or even interference from another infrared emit- ting source.

| Place the printer near to the transmitting instrument and take care that there is no object between the printer and the transmitting instru- ment.

Maintenance

paper tear-off bar
print head
paper sensor

Periodically and after a long print, it may be necessary to clean the print head, the paper sensor and the platen roll.

Open the cover of the paper compartment and remove the paper.
Loosen dirt particles at the paper sensor and tear of bar with a small soft brush.
Soak a Q-tip in isopropanol (IPA) and gently clean the print head.

ATTENTION!
Never use sharp objects for cleaning.
This might cause damage to the print head

Accessories

Thermopaper, 57 mm, 10 rolls part n° 4145

Warranty and Service

Warranty

If used properly, the warranty period for the Wöhler TD 100 will be twelve month from the date of sale. Batteries and paper rolls are not covered by this warranty.
This warranty does not cover the freight and packing costs when the device is sent to the factory for repair.

Service by non authorized personnel or making modifications to the analyzer voids any warranty.

Service

Wöhler has built our reputation on excellence in customer service. Therefore, of course, we are readily available to assist you after the warranty period ends.

Send us the device and we will repair it and return it to you with our package service.
Immediate help is provided by our technical staff over the telephone.

Declaration of conformity

The product: Wöhler TD 100 Thermal Printer

complies with the key safety requirements set down in the guidelines of the Council for the Harmonization of the Legal Requirements of the Member States in relation to the electromagnetic compatibility (EMC 2014/30/EU).
The following standards were availed of to evaluate the product in respect of the electromagnetic compatibility:

EN 55032 :2015+A1 :2020
EN 55035 :2017+A11 :2020
IEC 61000-4-2 :2008
IEC 61000-4-3 :2006+A1 :2007+A2 :2010
IEC 61000-4-8 :2009

Bad Wünnenberg, 29.03.2023

Signature
Johannes Lötfering, Geschäftsführer/Managing Director

Points of sale and service

Germany
Wöhler Technik GmbH
Wöhler-Platz 1
33181 Bad Wünnenberg
Tel.: +49 2953 73-100
Fax: +49 2953 73-96100
info@woehler.de
www.woehler.de

Wöhler West
Steiger-Stein-Str. 5
44805 Bochum
Tel.: +49 234 516993-0
Fax: +49 234 516993-99
west@woehler.de

Wöhler Süd
Gneisenaustr.12
80992 München
Tel.: +49 89 1589223-0
Fax: +49 89 1589223-99
sued@woehler.de

USA
Wohler USA Inc.
208 S Main Street
Middleton, MA 01949
Tel.: +1 978 750 9876
www.wohlerusa.com

Italy
Wöhler Italia srl
Via Coraine 21
37010 Costermano VR
Tel. +39 045 6200080
Fax. +39 045 6201508
info@woehler.it
www.woehler.it

Austria
Wöhler GmbH
Industriezone Burgerfeld 16
3150 Wilhelmsburg
Tel.: +43 2746 3131310
info@woehler.at

Czech Republic
Wöhler Bohemia s.r.o.
Za Naspern 1993
393 01 Pelhrimov
Tel.: +420 565 323 076
Fax: +420 565 323 078
info@woehler.cz

France
Wöhler France SARL
17 impasse de Grousset
31590 LAVALETTE
Tel.: +33 5 61 52 40 39
Fax: +33 5 62 27 11 31
info@woehler.fr
www.woehler.fr

Your contact:

WHLER Logo