Westinghouse 5104700 Baffle Trimmed Medium Base LED Instruction Manual
- June 15, 2024
- Westinghouse
Table of Contents
Westinghouse 5104700 Baffle Trimmed Medium Base LED
Important Information
LED 5” & 6” RETROFIT TRIM INSTALLATION INSTRUCTIONS
Please read carefully and save these instructions, as you may need them at a later date.
GENERAL: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.
Remove the trim from the box and make sure that no parts are missing by referencing the PARTS illustrations. The LED retrofit luminaire conversion kit includes installation instruction, LED lamp and field-applied label.
SUITABLE FOR TYPE IC OR NON-IC LUMINAIRES.
INSTALL THIS TRIM IN RECESSED HOUSINGS THAT HAVE DIMENSIONS SHOWN IN FIG. 1.
THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS.
SUITABLE FOR WET LOCATIONS.
THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION. PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH THE APPLICABLE AND APPROPRIATE ELECTRICAL CODES. THE INSTALLATION GUIDE DOES NOT SUPERSEDE LOCAL OR NATIONAL REGULATIONS FOR ELECTRICAL INSTALLATIONS. FOR RETROFIT KITS CERTIFIED TO CANADIAN REQUIREMENTS.
WARNING – Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
WARNING – Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. Examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTRALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
ASSEMBLY AND INSTALLATION
INCANDESCENT HOUSINGS
-
Turn off power at circuit box to avoid possible electric shock.
-
Thread the SOCKET ADAPTER into the SOCKET (FIG. 2).
-
Use the toggle switch to select your desired lamp color temperature – Soft White (2700K),
Warm White (3000K), Bright White (3500K), Cool White (4000K) or Daylight (5000K) (FIG. 3).
-
According to the size of recessed fixture to choose 5” or 6” installation, slide the springs/clips to the position which marks 5” or 6”.
*For torsion spring option, please follow below steps.
4a.Squeeze both TORSION SPRING arms together and insert into the TORSION
SPRING SLOTS (or RECEIVER BRACKETS) of the recessed housing. Tuck all wires
into the recessed housing and carefully push the RETROFIT TRIM into recessed
housing. (NOTE:** To provide enough room in shallow cans, carefully position
SOCKET ADAPTER and SOCKET adjacent to the long side of the LED DRIVER prior to
inserting the RETROFIT TRIM into the recessed housing.) (FIG. 4a)
Note: For 5″ installation, slide the springs to the position which marks 5″.
(Refer to Fig 5a, 6a, 7a & 8a)
*For the clip option, please remove torsion spring and replace with clips.
4b.Squeeze both clip arms together and insert into the clip of the recessed
housing. Tuck all wires into the recessed housing and carefully push the
RETROFIT TRIM into recessed housing. (NOTE: To provide enough room in shallow
recessed housing, carefully position SOCKET ADAPTER and SOCKET adjacent to the
long side of the LED DRIVER prior to inserting the RETROFIT TRIM into the
recessed housing.) (FIG. 4b)
Note:** For 5″ installation, slide the clips to the position which marks
5″.
(Refer to Fig 5b, 6b, 7b, 8b & 9b)
DIMMING
Although this product is compatible with most common residential type dimmers, dimming performance depends on dimmer, dimmer setting (for dimmers with brightness range adjustments), wiring method, and the number of LED modules. For best results, set dimmer position at maximum before adjusting to a lower light level.
Recommended Dimmers (minimum load for four LED modules maybe required for
optimal dimming performance): Levtion:6674-10W, IPL06-10Z, RDL06-10Z,
R50-1PL06-10M. Lutron:
DVCL-150PR-WH, CTCL-150PDH-WH, TGCL-153PH-WH, MACL-153MH-WH.
LIMITED WARRANTY
This lamp is warranted to be free from defects in materials and workmanship
for 5 years. If the product fails during the warranty period, return defective
product to seller.
Warranty terms and conditions of seller apply. If replacement product is not
available through seller, please contact www.westinghouselighting.com
/contact-us.
CUSTOMER SUPPORT
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
www.westinghouselighting.com
and Westinghouse are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
All Rights Reserved.
Made in China
Documents / Resources
|
Westinghouse 5104700 Baffle Trimmed Medium Base
LED
[pdf] Instruction Manual
5104700 Baffle Trimmed Medium Base LED, 5104700, Baffle Trimmed Medium Base
LED, Trimmed Medium Base LED, Medium Base LED, Base LED, LED
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>