AQUABATOS B0C282ZZ3W NIMES Glass Corner Shower Folding Doors User Guide
- June 15, 2024
- AQUABATOS
Table of Contents
AQUABATOS B0C282ZZ3W NIMES Glass Corner Shower Folding Doors
Product Information
Specifications:
- 1x Flachkopfschraube ST 4×30
- 2x Lippendichtung
- 1x Stabilisationsstange
- 2x Wandprofil Abdeckkappe
- 2x Griff
- 1x Vertikalesprofil Abdeckkappe L&R
- 2x Gummipuffer
- 2x Wandprofil
- 1x Festteil
- 8x Rundkopfschraube ST 4×30
- 9x Schraubdeckel Klemmen
- 9x Rundkopfschraube ST 4×12
- 9x Schrauben Abdeckkappe
- 2x Lagerzapfen oben
- 2x Lagerzapfen unten
- 2x Glasklemme A
- 2x Duschablage
- 2x Glasklemme B
- 2x Lageraufnahmeprofil
- 2x Vertikale Dichtung
- 1x Endabdeckkappe C Karton
- 2x Magnetdichtung
Product Usage Instructions
Step 1: Preparing for I nstallation
Step 2: Assembling the Parts
Follow the diagram below to assemble the parts:
Step 3: Mounting the Stabilization Bar
Take the stabilizations bar (1x) and attach it to the designated area on the
wall using the provided screws (1x Flachkopfschraube ST 4×30).
Step 4: Attaching Wall Profiles
Attach the wall profiles (2x) to the wall using the provided screws (8x
Rundkopfschraube ST 4×30).
Step 5: Installing Vertical Profiles
Attach the vertical profiles (1x Vertikalesprofil Abdeckkappe L&R and 2x
Wandprofil) to the wall profiles using the provided screws (8x
Rundkopfschraube ST 4×30).
Step 6: Mounting the Fixed Panel
Attach the fixed panel (1x Festteil) to the vertical profiles using the
provided screws (8x Rundkopfschraube ST 4×30).
Step 7: Installing Glass Clamps
Attach the glass clamps (2x Glasklemme A) to the fixed panel using the
provided screws (4x Drehlageraufnahme).
Step 8: Installing Glass Shelves
Attach the glass shelves (2x Duschablage) to the glass clamps using the
provided screws (4x Drehlager).
Step 9: Attaching Door Hinges
Attach the door hinges (4x Scharnier) to the glass door using the provided
screws (12x Flachkopfschraube ST 3.5×30).
Step 10: Installing Door Seals Attach the door seals (4x Bodendichtung)
to the bottom of the
glass door.
Step 11: Mounting Door Handles
Attach the door handles (2x Griff) to the glass door.
Step 12: Installing Magnetic Seals
Attach the magnetic seals (2x Magnetdichtung) to the glass door.
Step 13: Installing Bottom Pivot Pins
Insert the bottom pivot pins (2x Lagerzapfen unten) into the designated holes
on the floor.
Step 14: Installing Top Pivot Pins
Insert the top pivot pins (2x Lagerzapfen oben) into the designated holes on
the top of the glass door.
Step 15: Adjusting Glass Door
Adjust the glass door to ensure proper alignment and functionality.
Step 16: Finalizing Installation
Secure all screws and check for any loose parts. Make sure the nano-coated
side of the glass is facing inward for proper water repellency.
FAQ:
Q: What should I do if any parts are missing?
A: Please contact our customer service at info@aqualavos.de with your order
details, and we will assist you in obtaining the missing parts.
Q: How do I clean the glass panels?
A: Use a non-abrasive glass cleaner and a soft cloth to clean the glass
panels. Avoid using harsh chemicals or abrasive materials that may scratch the
surface.
Q: Can I install the shower enclosure without a stabilizing
bar?
A: No, the stabilizing bar is necessary for proper installation and
stability of the shower enclosure.
Q: Can I adjust the height of the glass door?
A: Yes, you can adjust the height of the glass door by adjusting the pivot
pins. Refer to the user manual for detailed instructions on adjusting the door
height.
Q: How can I prevent water leakage?
A: Ensure that all seals and gaskets are properly installed and in good
condition. Regularly check for any signs of wear or damage and replace as
needed. Additionally, make sure the door is properly aligned and closes
tightly to prevent water leakage.
info@aquabatos.com
www.aquabatos.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>