AQUABATOS NBD04 NIMES Series Rotary Folding Door Instruction Manual
- June 8, 2024
- AQUABATOS
Table of Contents
AQUABATOS NBD04 NIMES Series Rotary Folding Door
Installation instructions
Prior to installation please carefully examine shower enclosure for transport
or other damage. Thorough examination of all glass parts is essential for your
own safety. Seemingly minor damage may cause breakage of glass and for this
reason, extra care must be taken not to damage the glass edges of the shower
enclosure during installation or use of the shower enclosure. Claims for
transport damage after installation and claims for damage or cost caused by
incorrect installation, cleaning and maintenance will not be paid. Personal
protective equipment recommended !
Shower enclosures are intended for installation on shower trays. If installing
without a shower tray, the floor on which the shower enclosure will rest must
be flat and level. If installing on a joint or uneven surface, you must
ensure this is properly silicone to form a waterproof and maintenance-free
seal. When assembled off-floor or with a step, you must take appropriate
measures to prevent slip hazards on entry and exit. Before drilling the raw
plug holes, the wall has to be tested for concealed service pipes
(electricity-, gas- or water pipes). Drilling into these pipes is a life
threatening hazard as well as damage to property. Shower enclosures should be
installed on solid walls and bases. If installing on non-solid walls and
bases, you must ensure appropriate stability on site (e.g. by using special
raw plugs). Please use adequate and correct silicone appropriate for the
installation (e.g. for marble)
TOOL LIST
DESCRIPTION | BILD |
---|---|
Miliband | |
level | |
Rigid | |
06mm Bohre | |
03mm drill | |
DESCRIPTION | BILD |
--- | --- |
drilling machine | |
Flat Head Screwdriver | |
cross screwdriver | |
Hammer | |
silicone syringe |
NIMES corner shower with rotating folding doors
ASSEMBLY INSTRUCTIONS – DRAWING
- 2x wall profile cover cap
- 6x Dowels
- 2x wall profile
- 6x round head screw ST 4×30
- 2x Fixed Glass Plate
- 6x screw cover cap
- 6x round head screw ST 4×12
- 6x screw cap terminals
- 4x bottom seal
- 2x End Cover A L&R
- 2x drip tray
- 1x End Cover B
- 1x End Cover C
- 2x wood spacers
- 2x handle
- 2x Magnetic Gasket
- 2x Movable Plate
- 4x hinge
- 2x Vertical Gasket
- 2x rubber bumpers
INSTALLATION GUIDE
If you need assistance, we recommend that you contact a competent contact plumber.
Step 1
step 2
Shower trays installation dimension| Shower cabin installation
dimensions
---|---
68,5 – 70 cm| 67,5 – 69 cm
73,5 – 75 cm| 72,5 – 74 cm
78,5 – 80 cm| 77,5 – 79 cm
88,5 – 90 cm| 87,5 – 89 cm
98,5 – 100 cm| 97,5 – 99 cm
118,5 – 120 cm| 117,5 – 119 cm
Shower tray installation dimensions = the clear external dimensions of the
Shower tray, measured from the wall to the outer edge of the tub.
Shower stall installation dimensions = the maximum possible Outside
dimensions, measured from the wall to the outside edge of the profile.
step 3
step 4
step 5
step 6
Notice: Bille make sure that the : lower ropes of the Manel seal , first
flush mild lower ropes closing the glass pane.
step 7
step 8
step 9
step 10
step 11
Aqua Bates Bader GmbH
Southwest Corso 14
12161 Berlin
info@aquabatos.com
www.aquabatos.de
V01.09.2021
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>